Bunn CDBCF APS-MV Troubleshooting, Before troubleshooting this brewer, check for the following

Page 11

TROUBLESHOOTING

A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic Technical Service Department.

•Inspection, testing, and repair of electrical equipment should be performed only by qualified service personnel.

•All electronic components have 120 volt ac and low voltage dc potential on their terminals. Shorting of terminals or the application of external voltages may result in board failure.

•Intermittent operation of electronic circuit boards is unlikely. Board failure will normally be permanent. If an intermittent condition is encountered, the cause will likely be a switch contact or a loose connection at a terminal or crimp.

•Solenoid removal requires interrupting the water supply to the valve. Damage may result if solenoids are energized for more than ten minutes without a supply of water.

•The use of two wrenches is recommended whenever plumbing fittings are tightened or loosened. This will help to avoid twists and kinks in the tubing.

•Make certain that all plumbing connections are sealed and electrical connections tight and isolated.

•This brewer is heated at all times. Keep away from combustibles.

WARNING – • Exercise extreme caution when servicing electrical equipment.

•Unplug the brewer when servicing, except when electrical tests are specified.

•Follow recommended service procedures.

•Replace all protective shields or safety notices.

Before troubleshooting this brewer, check for the following:

Control Boards

1.Make sure ribbon cable is properly attached to the control board (ALL PINS INSERTED INTO PLUG).

2.Make sure there is a nylon insulating washer under each screw head that holds the control board to the plastic front end cap. This is important for proper operation.

3.Make sure before servicing brewer that voltage is present at control board.

4.Press any warmer switch or observe if any indicator lights are glowing on the control panel. If so, proceed with testing. If not, check for voltage across pins 1 & 2 of the ten pin J1 connector (black and white wires). If voltage is present, replace the control board. If voltage is not present, check wiring and voltage across terminal block (black and white). Correct the problem and retest before proceeding with testing.

Page 11

29707 112801

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents DIS Version Introduction APS Brewers TWO Warmer BrewersThree Warmer Brewers ONE Warmer Brewers CDBCF-DV BrewersCdbc LPTC-DV Brewers No Warmer BrewersElectrical HOOK-UP Electrical Requirements1425W Version Models CDBC-MV & CDBC-APS MV Coffee Brewing CleaningPlumbing Requirements Initial SET-UPReady Indicator ON/OFF SwitchBrew Switch Additional Warmer SwitchesSetting Brew Lockout Adjustments & Optional SettingsSetting Brew Temperature Displaying Brew TemperatureWater Sensing Threshold Adjustment Procedure Before troubleshooting this brewer, check for the following TroubleshootingRemedy TroubleshootingRefill Circuit Problem Probable Cause Troubleshooting Refill Circuit Water does not heat to proper tem- perature Heating Circuit ProblemIngs are taken Troubleshooting Heating CircuitProblem Probable Cause Tank HeaterProblem Probable Cause Remedy Brewing Circuit Problem Probable Cause Brew cycle will not start Control board or dispense valve Troubleshooting Brewing CircuitConsistently low beverage level Brew volume Dispenser Be made with sprayhead installedRequired Water temperatureSet-upinstructions Dripping from sprayhead Lime build upProblem Probable Cause Cause Things to Check DiagnosticsComponent Access ServiceWhen servicing, except when electrical tests are re Control Board ServiceDisconnect the 11-pin connector from the control panel Switch Panel Dispense Valve Limit Thermostat Limit Thermostat WiringTank Heaters Tank Heater Terminal Block Wiring Diagram Voltage Selector Switch Terminals Refill Valve Warmer Elements Warmer ElementsFuse HOLDER/FUSE Assembly MV models only Thermal Fuses Service Thermal Fuses MV models onlySchematic Wiring Diagram Cdbc DV Schematic Wiring Diagram Cdbc APS-DV Cdbcf APS/TC/LPTC-DV Schematic Wiring Diagram Cdbc MV Schematic Wiring Diagram Cdbc APS MV
Related manuals
Manual 2 pages 47.58 Kb

CDBCF-MV, CDBCF APS-DV, CDBCF APS-MV, CDBC-DV, CDBC-MV specifications

The Bunn CDBCF-DV is a distinguished coffee brewer designed for commercial use, ideal for establishments that demand high-quality coffee at a fast pace. This brewer is notable for its innovative design and advanced brewing technology, making it an essential asset for cafes, restaurants, and coffee shops.

One of the standout features of the Bunn CDBCF-DV is its dual-voltage capability. This versatility allows the brewer to operate efficiently on both 120V and 240V power sources, ensuring that it meets the needs of various establishments regardless of electrical setup. This adaptability makes it a favorite among coffee vendors looking to optimize performance without the inconvenience of electrical constraints.

The BDCBF-DV also boasts a large capacity, allowing it to brew up to 14 cups of coffee in a single cycle. This is facilitated by its large water tank and high brewing rate, which can produce coffee in just a matter of minutes. The ability to brew rapidly while maintaining quality is crucial in busy environments where time is of the essence.

Key to the Bunn CDBCF-DV's performance is its patented brewing system that utilizes a pre-infusion feature. This technology ensures that the coffee grounds are saturated before the brewing process begins, promoting optimal extraction of flavors and aromas. The result is a rich, well-balanced cup of coffee that delights patrons and encourages repeat business.

Another notable characteristic is the brewer's easy-to-use control interface. With simple dial settings, baristas can effortlessly adjust brew strength and temperature, ensuring consistency with every batch. The intuitive design minimizes training time for new staff and enhances overall workflow in commercial settings.

Durability and maintenance are critical in commercial coffee brewing equipment, and the Bunn CDBCF-DV excels in this area as well. Constructed with high-quality materials, it is built to withstand the rigors of daily use. Additionally, it features easily accessible parts for straightforward cleaning and servicing, reducing downtime and ensuring that the coffee remains fresh and delicious.

In summary, the Bunn CDBCF-DV is a versatile, efficient, and user-friendly coffee brewer loaded with innovative features aimed at delivering exceptional coffee quality. Its dual-voltage operation, large capacity, pre-infusion technology, and durable design make it an indispensable choice for businesses looking to enhance their coffee offerings and improve customer satisfaction. Whether you're a small cafe or a larger restaurant chain, the Bunn CDBCF-DV is engineered to meet your coffee brewing demands with excellence.
Top Page Image Contents