Bunn CDBCF APS-DV, CDBCF-DV, CDBC-MV Electrical Requirements, 1425W Version, Electrical HOOK-UP

Page 5

Models CDBC-DV, CDBC-APS DV & CDBCF LPTC-DV

ELECTRICAL REQUIREMENTS

CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up.

Brewers with an attached cord set require 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz. Requirements for brewers without an attached cord set are as follows:

1425W VERSION

3180W VERSION

Requires 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz.

Requires 3-wire, grounded service rated 120/240 volts ac, 20 amp, single phase, 60 Hz.

ELECTRICAL HOOK-UP

CAUTION – Improper electrical installation will damage electronic components. The toggle switch is set to operate on a 120 volt, 15 amp service (1425W Version).

1.An electrician must provide electrical service.

2.Determine the available on-site electrical service.

3.Select the desired unit wattage based on the available on-site electrical service.

4.Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.

5.If the brewer is to be connected to 120/208 or 120/240 volts, remove the front access panel beneath the sprayhead and remove the power cord (if provided) from the terminal block.

6.Feed the supply leads through the rear of the brewer.

7.Using the above diagrams, connect the desired electrical service to the field wiring terminal block.

8.If re-wiring the machine for operation on 120/208 or 120/240 volts with a Power Supply Cord, the replacement

Power Supply Cord must be UL Listed Flexible Cord Type SO, SJO, SJTO, HSJO or SJOW, No. 12 AWG, 4 Conductor, Rated 90° C. Attachment Plug Cap must be UL Listed, NEMA 14-20P or L14-20P Configuration, Rated 125/250V, 20 AMPS. The Power Supply Cord must be at least 3 feet long and maximum 6 feet long (measured from Strain Relief to end of the Attachment Plug Cap).

9.Before proceeding, verify the voltage at the field wiring terminal block.

10.Set toggle switch on component bracket to the appropriate position (120/208-240V) and replace the access panel.

11.If plumbing is to be hooked up later be sure the brewer is disconnected from the power source. If plumbing has been hooked up, the brewer is ready for Initial Set-Up.

Page 5

29707 080503

 

Page 4 Page 6
Image 5
Page 4 Page 6
Contents DIS Version Introduction APS Brewers TWO Warmer BrewersThree Warmer Brewers Cdbc LPTC-DV Brewers CDBCF-DV BrewersNo Warmer Brewers ONE Warmer BrewersElectrical HOOK-UP Electrical Requirements1425W Version Models CDBC-MV & CDBC-APS MV Plumbing Requirements CleaningInitial SET-UP Coffee BrewingBrew Switch ON/OFF SwitchAdditional Warmer Switches Ready IndicatorSetting Brew Temperature Adjustments & Optional SettingsDisplaying Brew Temperature Setting Brew LockoutWater Sensing Threshold Adjustment Procedure Before troubleshooting this brewer, check for the following TroubleshootingRemedy TroubleshootingRefill Circuit Problem Probable Cause Troubleshooting Refill Circuit Water does not heat to proper tem- perature Heating Circuit ProblemProblem Probable Cause Troubleshooting Heating CircuitTank Heater Ings are takenProblem Probable Cause Remedy Brewing Circuit Problem Probable Cause Consistently low beverage level Brew volume Troubleshooting Brewing CircuitDispenser Be made with sprayhead installed Brew cycle will not start Control board or dispense valveSet-upinstructions Water temperatureDripping from sprayhead Lime build up RequiredProblem Probable Cause Cause Things to Check DiagnosticsComponent Access ServiceWhen servicing, except when electrical tests are re Control Board ServiceDisconnect the 11-pin connector from the control panel Switch Panel Dispense Valve Limit Thermostat Limit Thermostat WiringTank Heaters Tank Heater Terminal Block Wiring Diagram Voltage Selector Switch Terminals Refill Valve Warmer Elements Warmer ElementsFuse HOLDER/FUSE Assembly MV models only Thermal Fuses Service Thermal Fuses MV models onlySchematic Wiring Diagram Cdbc DV Schematic Wiring Diagram Cdbc APS-DV Cdbcf APS/TC/LPTC-DV Schematic Wiring Diagram Cdbc MV Schematic Wiring Diagram Cdbc APS MV
Related manuals
Manual 2 pages 47.58 Kb

CDBCF-MV, CDBCF APS-DV, CDBCF APS-MV, CDBC-DV, CDBC-MV specifications

The Bunn CDBCF-DV is a distinguished coffee brewer designed for commercial use, ideal for establishments that demand high-quality coffee at a fast pace. This brewer is notable for its innovative design and advanced brewing technology, making it an essential asset for cafes, restaurants, and coffee shops.

One of the standout features of the Bunn CDBCF-DV is its dual-voltage capability. This versatility allows the brewer to operate efficiently on both 120V and 240V power sources, ensuring that it meets the needs of various establishments regardless of electrical setup. This adaptability makes it a favorite among coffee vendors looking to optimize performance without the inconvenience of electrical constraints.

The BDCBF-DV also boasts a large capacity, allowing it to brew up to 14 cups of coffee in a single cycle. This is facilitated by its large water tank and high brewing rate, which can produce coffee in just a matter of minutes. The ability to brew rapidly while maintaining quality is crucial in busy environments where time is of the essence.

Key to the Bunn CDBCF-DV's performance is its patented brewing system that utilizes a pre-infusion feature. This technology ensures that the coffee grounds are saturated before the brewing process begins, promoting optimal extraction of flavors and aromas. The result is a rich, well-balanced cup of coffee that delights patrons and encourages repeat business.

Another notable characteristic is the brewer's easy-to-use control interface. With simple dial settings, baristas can effortlessly adjust brew strength and temperature, ensuring consistency with every batch. The intuitive design minimizes training time for new staff and enhances overall workflow in commercial settings.

Durability and maintenance are critical in commercial coffee brewing equipment, and the Bunn CDBCF-DV excels in this area as well. Constructed with high-quality materials, it is built to withstand the rigors of daily use. Additionally, it features easily accessible parts for straightforward cleaning and servicing, reducing downtime and ensuring that the coffee remains fresh and delicious.

In summary, the Bunn CDBCF-DV is a versatile, efficient, and user-friendly coffee brewer loaded with innovative features aimed at delivering exceptional coffee quality. Its dual-voltage operation, large capacity, pre-infusion technology, and durable design make it an indispensable choice for businesses looking to enhance their coffee offerings and improve customer satisfaction. Whether you're a small cafe or a larger restaurant chain, the Bunn CDBCF-DV is engineered to meet your coffee brewing demands with excellence.
Top Page Image Contents