Bunn CDBC-MV Adjustments & Optional Settings, Setting Brew Temperature, Setting Brew Lockout

Page 9

ADJUSTMENTS & OPTIONAL SETTINGS

HIDDEN

SWITCH

P1866

Setting Brew Temperature

The brewer is factory set to brew at 200°F (95°C). To change this setting, press and hold the "HIDDEN" switch beneath the "®". The word "TEMP" above the "ON/OFF" switch will glow to correspond with the temporary function change of this switch. Repeatedly press and release the "ON/OFF" switch until one of the bank of temperature indicators shows the approximate desired temperature. When two indicators are glowing, the temperature is approximately the number between them.

Displaying Brew Temperature

The brewer is factory set with the temperature display disabled. To change this setting, press and hold the "ON/ OFF" switch and the "HIDDEN" switch beneath the "®" for five seconds, the entire bank of temperature indicators will glow. Release both switches. Pressing and releasing the "ON/OFF" switch will toggle between turning the entire bank of temperature indicators on-or-off, signifying the "ON" or "OFF" condition of this display. Wait for a few seconds, the brewer will maintain this last setting.

Setting Brew Lockout

The brewer is factory set with the brew lockout disabled. Brew lockout prevents starting a brew cycle if the ready indicator is not glowing. When an attempt at brewing cannot be allowed, the word "NOT" and "LOCKOUT" flash for three seconds to indicate the reason the brew can't begin. To change the condition of the brew lockout, press and hold the "HIDDEN" switch beneath the "®" and momentarily press the "BREW" switch.

Adjusting Automatic Warmer Shut-Off

The brewer is factory set with this feature disabled. The automatic warmer shut-off de-energizes all warmers after a predetermined time period after the most recent brew cycle. To change the setting, press and hold the "BREW" switch and the "HIDDEN" switch beneath the "®" for five seconds, the entire bank of temperature indicators will flash on-and-off. Release both switches. Pressing and releasing the "BREW" switch will select the number of temperature indicators from none to five. When no indicators are glowing, this feature is disabled and all warmers will be controlled only by their respective switches. When one to five indicators are glowing, it indicates the approximate number of hours of delay before all warmers will be automatically de-energized after the most recent brew cycle.

IMPORTANT: The tank must be full and fill solenoid shut off prior to making these adjustments. The sprayhead must be installed when making adjustments.

Adjusting Brew Volumes

The brewer is factory set to deliver 64 ounces ± 2 for each brew cycle.

BREW VOLUME SET-UP: Use the following steps when the setting is unknown or a different circuit board is being installed.

1.Place an empty funnel in the funnel rails and an empty decanter or graduated vessel beneath the funnel.

2.Press the "ON/OFF" switch (Indicator glowing).

Page 9

29707 112801

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents DIS Version Introduction TWO Warmer Brewers Three Warmer BrewersAPS Brewers Cdbc LPTC-DV Brewers CDBCF-DV BrewersNo Warmer Brewers ONE Warmer BrewersElectrical Requirements 1425W VersionElectrical HOOK-UP Models CDBC-MV & CDBC-APS MV Plumbing Requirements CleaningInitial SET-UP Coffee BrewingBrew Switch ON/OFF SwitchAdditional Warmer Switches Ready IndicatorSetting Brew Temperature Adjustments & Optional SettingsDisplaying Brew Temperature Setting Brew LockoutWater Sensing Threshold Adjustment Procedure Before troubleshooting this brewer, check for the following TroubleshootingTroubleshooting Refill Circuit Problem Probable CauseRemedy Troubleshooting Refill Circuit Water does not heat to proper tem- perature Heating Circuit ProblemProblem Probable Cause Troubleshooting Heating CircuitTank Heater Ings are takenProblem Probable Cause Remedy Brewing Circuit Problem Probable Cause Consistently low beverage level Brew volume Troubleshooting Brewing CircuitDispenser Be made with sprayhead installed Brew cycle will not start Control board or dispense valveSet-upinstructions Water temperatureDripping from sprayhead Lime build up RequiredProblem Probable Cause Cause Things to Check DiagnosticsService When servicing, except when electrical tests are reComponent Access Service Disconnect the 11-pin connector from the control panelControl Board Switch Panel Dispense Valve Limit Thermostat Limit Thermostat WiringTank Heaters Tank Heater Terminal Block Wiring Diagram Voltage Selector Switch Terminals Refill Valve Warmer Elements Warmer ElementsFuse HOLDER/FUSE Assembly MV models only Thermal Fuses Service Thermal Fuses MV models onlySchematic Wiring Diagram Cdbc DV Schematic Wiring Diagram Cdbc APS-DV Cdbcf APS/TC/LPTC-DV Schematic Wiring Diagram Cdbc MV Schematic Wiring Diagram Cdbc APS MV
Related manuals
Manual 2 pages 47.58 Kb

CDBCF-MV, CDBCF APS-DV, CDBCF APS-MV, CDBC-DV, CDBC-MV specifications

The Bunn CDBCF-DV is a distinguished coffee brewer designed for commercial use, ideal for establishments that demand high-quality coffee at a fast pace. This brewer is notable for its innovative design and advanced brewing technology, making it an essential asset for cafes, restaurants, and coffee shops.

One of the standout features of the Bunn CDBCF-DV is its dual-voltage capability. This versatility allows the brewer to operate efficiently on both 120V and 240V power sources, ensuring that it meets the needs of various establishments regardless of electrical setup. This adaptability makes it a favorite among coffee vendors looking to optimize performance without the inconvenience of electrical constraints.

The BDCBF-DV also boasts a large capacity, allowing it to brew up to 14 cups of coffee in a single cycle. This is facilitated by its large water tank and high brewing rate, which can produce coffee in just a matter of minutes. The ability to brew rapidly while maintaining quality is crucial in busy environments where time is of the essence.

Key to the Bunn CDBCF-DV's performance is its patented brewing system that utilizes a pre-infusion feature. This technology ensures that the coffee grounds are saturated before the brewing process begins, promoting optimal extraction of flavors and aromas. The result is a rich, well-balanced cup of coffee that delights patrons and encourages repeat business.

Another notable characteristic is the brewer's easy-to-use control interface. With simple dial settings, baristas can effortlessly adjust brew strength and temperature, ensuring consistency with every batch. The intuitive design minimizes training time for new staff and enhances overall workflow in commercial settings.

Durability and maintenance are critical in commercial coffee brewing equipment, and the Bunn CDBCF-DV excels in this area as well. Constructed with high-quality materials, it is built to withstand the rigors of daily use. Additionally, it features easily accessible parts for straightforward cleaning and servicing, reducing downtime and ensuring that the coffee remains fresh and delicious.

In summary, the Bunn CDBCF-DV is a versatile, efficient, and user-friendly coffee brewer loaded with innovative features aimed at delivering exceptional coffee quality. Its dual-voltage operation, large capacity, pre-infusion technology, and durable design make it an indispensable choice for businesses looking to enhance their coffee offerings and improve customer satisfaction. Whether you're a small cafe or a larger restaurant chain, the Bunn CDBCF-DV is engineered to meet your coffee brewing demands with excellence.
Top Page Image Contents