Bunn CDS-3 manual Whipper Motor, Volts ac for 120 volt models Volts ac for 230 volt CE models

Page 16

SERVICE (cont.)

WHIPPER MOTOR

P1924

FIG. 8 WHIPPER MOTOR

Location:

The whipper motor is located on the back side of the whipper motor mounting panel.

Test Procedure:

1.Disconnect the dispenser from the power source.

2.Disconnect the white/red and white/brown wires of the main wiring harness from the black leads of the whipper motor.

3.With the CDS hopper level lower than the probe, press and hold the SERVICE switch and check the voltage across the disconnected harness wires with a voltmeter. Connect the dispenser to the power source. The indication must be:

a)120 volts ac for 120 volt models.

b)230 volts ac for 230 volt CE models.

4.Disconnect the dispenser from the power source.

If voltage is present as described, replace the motor. If voltage is not present as described, refer to the wiring diagrams and check the dispenser wiring harness.

Removal and Replacement:

1.Disconnect the dispenser from the power source.

2.Open the dispenser door and remove the hopper assembly out the front of the dispenser.

3.Remove the four #8-32 screws securing the hopper support panel to the auger motor mounting panel and the whipper motor mounting panel.

4.Slowly lift the hopper support panel up and discon- nect the red/black and green wires from the hopper switch.

5.Pull the mixing chamber out of the whipper cham- ber.

6.Twist the whipper chamber clockwise and pull it off the whipper chamber receptacle.

7.Pull the frother off the motor shaft. Notice the flat side on the shaft and the matching flat inside the frother. It is important that these two flats are lined up when reassembling.

8.Slide the receptacle with seal off of the motor shaft.

NOTE: To remove the receptacle only, rotate clockwise until the receptacle clears the nuts and slide off of the motor shaft.

9.Slide the slinger off of the motor shaft.

10.Remove the two nuts securing the whipper chamber receptacle and whipper motor to the front panel.

11.Disconnect the black leads on the motor from the white/red and white/brown wires of the main wiring harness and remove the motor.

12.Install new motor on rear of front panel and secure with two nuts. Connect the black leads from the motor to the main wiring harness. Refer to Fig. 9

16

29793 011500

 

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Powder Auto Fill Post Office BOX SPRINGFIELD, IllinoisIntroduction BUNN-O-MATIC Commercial Product WarrantyInitial SET-UP User Notices Operating Instructions Adjustments Cleaning Recommended Daily Cleaning and Maintenance TipsFault List Normal operation Powder Auto-Fill ready toDispense Door not closedTroubleshooting Problem Probable CauseProblem RemedyProblem Probable Cause Remedy Procedures. See Improper adjustment of productInstall a regulator if necessary to Product overflows CDS hopper Control Board and ProbeService Component AccessAuger Drive Components Hopper LidRetainer Clip Spacer Dust Seal Hopper BaseDisconnect the dispenser from the power source Auger Drive MotorFrother and MIXING/WHIPPER Chamber Mixing ChamberWhipper Motor Volts ac for 120 volt models Volts ac for 230 volt CE modelsInstall dispense tip into the bottom of the whipper chamber Whipper MotorControl Board and Level Probe If voltage is present as described, proceed to #9Test Procedure Low Product Detect Instal the new control board using the four #6-32 keps nuts Remove the control boardTEST/SERVICE Switch LocationMain Power ON/OFF Switch Main Power ON/OFF SwitchLamp Cord Assembly Refer to when reconnecting the wiresDisconnect the lamp cord from the lamp cord con- nector Lamp Cord ConnectorIf voltage is present as described, proceed to #6 Lamp HOLDER/SOCKET Assembly Lamp HOLDER/SOCKET AssemblyTransformer TransformerPotentiometer PotentiometerHopper Level Indicator Hopper Level IndicatorHopper Switch Hopper SwitchDoor Switch Door SwitchAdjustments Pressure Regulator and Needle ValveDispense Solenoid Valve Dispense Solenoid ValveWiring Diagrams Schematic Wiring Diagram PAF BLK REDWiring Diagrams Schematic Wiring Diagram Pafa BLK
Related manuals
Manual 60 pages 54.74 Kb Manual 34 pages 32.1 Kb

CDS-3 specifications

The Bunn CDS-3 is a commercial coffee brewer renowned for its reliability, efficiency, and high-quality performance. Designed for busy environments such as cafés, restaurants, and convenience stores, it offers the perfect balance of capacity and functionality, making it ideal for high-demand situations.

One of the standout features of the Bunn CDS-3 is its ability to brew up to 3.8 gallons of coffee per hour. This impressive capacity meets the needs of busy establishments where a constant supply of fresh coffee is crucial. The brewer’s stainless steel construction not only ensures durability but also maintains temperature, thus preserving the coffee’s rich flavor and aroma.

The CDS-3 incorporates Bunn's patented brewing technology, including the "Pour-Over" method. This feature allows for easy operation and contributes to the even extraction of coffee grounds. The machine is equipped with a pre-infusion mode that saturates coffee grounds before brewing, enhancing extraction for a fuller, more complex flavor profile.

Temperature control is another vital characteristic of the Bunn CDS-3. It maintains the water temperature between 195°F to 205°F, the ideal range for optimal coffee brewing. The brewer’s internals are designed for rapid heating, ensuring that the water reaches the desired temperature quickly and consistently, which is essential for high-quality coffee production.

In terms of usability, the Bunn CDS-3 offers an intuitive interface, allowing staff to operate it with minimal training. The front-access design not only simplifies maintenance, but also makes it easy to refill water and perform routine cleaning. Furthermore, the large capacity coffee pots ensure that the brewed coffee can be stored efficiently, minimizing waste.

Equipped with a unique spray head system, the Bunn CDS-3 ensures uniform saturation of the coffee grounds. This feature supports optimal extraction, allowing users to produce a rich and flavorful brew that keeps customers coming back for more.

In summary, the Bunn CDS-3 is a well-engineered, commercial-grade coffee brewer that excels in high-demand environments. Its robust construction, advanced brewing technology, consistent temperature control, and user-friendly design make it a favorite among coffee enthusiasts and professionals alike, affirming its reputation as a reliable and effective solution for coffee brewing needs. Whether for a bustling café or a catering service, the Bunn CDS-3 delivers a consistently great cup of coffee every time.
Top Page Image Contents