Bunn CDS-3 manual User Notices

Page 3

10.Slowly feed the door support arms through the slots located on the front of the Powder Auto-Fill.

11.Continue to slowly feed the door support arms through the slots until the magnet strikes on the back of the door engage the magnets on the Powder Auto-Fill.

12.Locate the #8-32 x .375” truss head screws and brass spacers set aside earlier.

13.Place one brass spacer on each screw.

14.Insert one screw/spacer assembly through the door hinge, locating the spacer inside the hinge bushing and threading the screw into the hinge mount on the Powder Auto-Fill cover. Repeat for other side.

15.Install PAF level probe (BOM #29728.1000) by sliding it into the notched area at the top rear of the CDS hop- per. The probe should be firmly seated in the notch and touching the contact pin protruding from the front of the CDS cooling drum mount.

NOTE: At this point, it is important that the CDS machine is fully assembled according to the instructions outlined in the CDS Operating and Service Manual.

16.Place the assembled Powder Auto-Fill on top of a hopper of a fully assembled CDS machine, taking care to align the Powder Auto-Fill guide rails over the rollers on the CDS.

17.Connect the Powder Auto-Fill power cord to the outlet located on the CDS auger motor cover.

18.Attach a flexible water line to the .25” flare fitting on the back panel of the Powder Auto-Fill.

NOTE: A water strainer assembly (BUNN-O-MATIC #23820.1000) should be installed in line prior to the flexible water line.

USER NOTICES

Carefully read and follow all notices on the equipment and in this manual. They were written for your protection. All notices are to be kept in good condition. Replace any unreadable or damaged labels.

This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the Food and Drug Administration (FDA). For models installed outside the U.S.A., comply with the applicable Plumbing /SanitationCode.

00656.0000

Push back until fully latched before removing or manually filling chilled product hopper.

34561.0000

00986.0000

3

29793 080102

 

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Post Office BOX SPRINGFIELD, Illinois Powder Auto FillBUNN-O-MATIC Commercial Product Warranty IntroductionInitial SET-UP User Notices Operating Instructions Adjustments Recommended Daily Cleaning and Maintenance Tips CleaningDoor not closed Fault ListNormal operation Powder Auto-Fill ready to DispenseProblem Probable Cause TroubleshootingRemedy ProblemProblem Probable Cause Remedy Product overflows CDS hopper Control Board and Probe Procedures. SeeImproper adjustment of product Install a regulator if necessary toComponent Access ServiceSpacer Dust Seal Hopper Base Auger Drive ComponentsHopper Lid Retainer ClipAuger Drive Motor Disconnect the dispenser from the power sourceMixing Chamber Frother and MIXING/WHIPPER ChamberVolts ac for 120 volt models Volts ac for 230 volt CE models Whipper MotorWhipper Motor Install dispense tip into the bottom of the whipper chamberIf voltage is present as described, proceed to #9 Control Board and Level ProbeTest Procedure Low Product Detect Remove the control board Instal the new control board using the four #6-32 keps nutsLocation TEST/SERVICE SwitchMain Power ON/OFF Switch Main Power ON/OFF SwitchRefer to when reconnecting the wires Lamp Cord AssemblyLamp Cord Connector Disconnect the lamp cord from the lamp cord con- nectorIf voltage is present as described, proceed to #6 Lamp HOLDER/SOCKET Assembly Lamp HOLDER/SOCKET AssemblyTransformer TransformerPotentiometer PotentiometerHopper Level Indicator Hopper Level IndicatorHopper Switch Hopper SwitchDoor Switch Door SwitchPressure Regulator and Needle Valve AdjustmentsDispense Solenoid Valve Dispense Solenoid ValveBLK RED Wiring Diagrams Schematic Wiring Diagram PAFBLK Wiring Diagrams Schematic Wiring Diagram Pafa
Related manuals
Manual 60 pages 54.74 Kb Manual 34 pages 32.1 Kb

CDS-3 specifications

The Bunn CDS-3 is a commercial coffee brewer renowned for its reliability, efficiency, and high-quality performance. Designed for busy environments such as cafés, restaurants, and convenience stores, it offers the perfect balance of capacity and functionality, making it ideal for high-demand situations.

One of the standout features of the Bunn CDS-3 is its ability to brew up to 3.8 gallons of coffee per hour. This impressive capacity meets the needs of busy establishments where a constant supply of fresh coffee is crucial. The brewer’s stainless steel construction not only ensures durability but also maintains temperature, thus preserving the coffee’s rich flavor and aroma.

The CDS-3 incorporates Bunn's patented brewing technology, including the "Pour-Over" method. This feature allows for easy operation and contributes to the even extraction of coffee grounds. The machine is equipped with a pre-infusion mode that saturates coffee grounds before brewing, enhancing extraction for a fuller, more complex flavor profile.

Temperature control is another vital characteristic of the Bunn CDS-3. It maintains the water temperature between 195°F to 205°F, the ideal range for optimal coffee brewing. The brewer’s internals are designed for rapid heating, ensuring that the water reaches the desired temperature quickly and consistently, which is essential for high-quality coffee production.

In terms of usability, the Bunn CDS-3 offers an intuitive interface, allowing staff to operate it with minimal training. The front-access design not only simplifies maintenance, but also makes it easy to refill water and perform routine cleaning. Furthermore, the large capacity coffee pots ensure that the brewed coffee can be stored efficiently, minimizing waste.

Equipped with a unique spray head system, the Bunn CDS-3 ensures uniform saturation of the coffee grounds. This feature supports optimal extraction, allowing users to produce a rich and flavorful brew that keeps customers coming back for more.

In summary, the Bunn CDS-3 is a well-engineered, commercial-grade coffee brewer that excels in high-demand environments. Its robust construction, advanced brewing technology, consistent temperature control, and user-friendly design make it a favorite among coffee enthusiasts and professionals alike, affirming its reputation as a reliable and effective solution for coffee brewing needs. Whether for a bustling café or a catering service, the Bunn CDS-3 delivers a consistently great cup of coffee every time.
Top Page Image Contents