Bunn CDS-3 manual Troubleshooting, Problem Probable Cause

Page 8

TROUBLESHOOTING

A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic Technical Service Department.

•Inspection, testing, and repair of electrical equipment should be performed only by qualified service person- nel.

•All electronic components have 120 volt ac and low voltage dc potential on their terminals. Shorting of terminals or the application of external voltages may result in board failure.

•Intermittent operation of electronic circuit boards is unlikely. Board failure will normally be permanent. If an intermittent condition is encountered, the cause will likely be a switch contact or a loose connection at a terminal or crimp.

•Solenoid removal requires interrupting the water supply to the valve. Damage may result if solenoids are energized for more than ten minutes without a supply of water.

•The use of two wrenches is recommended whenever plumbing fittings are tightened or loosened. This will help to avoid twists and kinks in the tubing.

•Make certain that all plumbing connections are sealed and electrical connections tight and isolated.

•Keep away from combustibles.

WARNING – • Exercise extreme caution when servicing electrical equipment.

•Unplug the dispenser when servicing, except when electrical tests are specified.

•Follow recommended service procedures

•Replace all protective shields or safety notices

PROBLEM

PROBABLE CAUSE

REMEDY

CDS and Powder Auto-Fill do not run - Main power indicator on CDS drawer front OFF

Product level in CDS is lower than level Probe - CDS running; Powder Auto-Fill door lamp is OFF

Product level in CDS is lower than level Probe - CDS running; Powder Auto-Fill door lamp flashes ON and

OFF

1.CDS power cord disconnected or main power switch in 0 position.

1.The CDS DAY/NIGHT switch in the NIGHT position.

2.The CDS DAY/NIGHT timer in the NIGHT position.

3.Powder Auto-Fill power cord disconnected.

4.Powder Auto-Fill main power switch in OFF position.

5.Powder Auto-Fill door is open.

1.Low product in Powder Auto- Fill.

Check that the power cord is con- nected to proper electrical source and that the CDS main power switch is in the 1 position.

1.The CDS DAY/NIGHT switch should be in the DAY position.

2.Reprogram the CDS DAY/NIGHT timer.

3.Check that the Powder Auto-Fill is plugged into the back of the CDS auger motor cover.

4.Select the ON position of the main power switch.

5.The Powder Auto-Fill door should be closed securely.

Remove hopper and fill with pow- dered mix.

8

29793 061599

 

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Powder Auto Fill Post Office BOX SPRINGFIELD, IllinoisInitial SET-UP BUNN-O-MATIC Commercial Product WarrantyIntroduction User Notices Operating Instructions Adjustments Cleaning Recommended Daily Cleaning and Maintenance TipsFault List Normal operation Powder Auto-Fill ready toDispense Door not closedTroubleshooting Problem Probable CauseProblem RemedyProblem Probable Cause Remedy Procedures. See Improper adjustment of productInstall a regulator if necessary to Product overflows CDS hopper Control Board and ProbeService Component AccessAuger Drive Components Hopper LidRetainer Clip Spacer Dust Seal Hopper BaseDisconnect the dispenser from the power source Auger Drive MotorFrother and MIXING/WHIPPER Chamber Mixing ChamberWhipper Motor Volts ac for 120 volt models Volts ac for 230 volt CE modelsInstall dispense tip into the bottom of the whipper chamber Whipper MotorControl Board and Level Probe If voltage is present as described, proceed to #9Test Procedure Low Product Detect Instal the new control board using the four #6-32 keps nuts Remove the control boardTEST/SERVICE Switch LocationMain Power ON/OFF Switch Main Power ON/OFF SwitchLamp Cord Assembly Refer to when reconnecting the wiresIf voltage is present as described, proceed to #6 Lamp Cord ConnectorDisconnect the lamp cord from the lamp cord con- nector Lamp HOLDER/SOCKET Assembly Lamp HOLDER/SOCKET AssemblyTransformer TransformerPotentiometer PotentiometerHopper Level Indicator Hopper Level IndicatorHopper Switch Hopper SwitchDoor Switch Door SwitchAdjustments Pressure Regulator and Needle ValveDispense Solenoid Valve Dispense Solenoid ValveWiring Diagrams Schematic Wiring Diagram PAF BLK REDWiring Diagrams Schematic Wiring Diagram Pafa BLK
Related manuals
Manual 60 pages 54.74 Kb Manual 34 pages 32.1 Kb

CDS-3 specifications

The Bunn CDS-3 is a commercial coffee brewer renowned for its reliability, efficiency, and high-quality performance. Designed for busy environments such as cafés, restaurants, and convenience stores, it offers the perfect balance of capacity and functionality, making it ideal for high-demand situations.

One of the standout features of the Bunn CDS-3 is its ability to brew up to 3.8 gallons of coffee per hour. This impressive capacity meets the needs of busy establishments where a constant supply of fresh coffee is crucial. The brewer’s stainless steel construction not only ensures durability but also maintains temperature, thus preserving the coffee’s rich flavor and aroma.

The CDS-3 incorporates Bunn's patented brewing technology, including the "Pour-Over" method. This feature allows for easy operation and contributes to the even extraction of coffee grounds. The machine is equipped with a pre-infusion mode that saturates coffee grounds before brewing, enhancing extraction for a fuller, more complex flavor profile.

Temperature control is another vital characteristic of the Bunn CDS-3. It maintains the water temperature between 195°F to 205°F, the ideal range for optimal coffee brewing. The brewer’s internals are designed for rapid heating, ensuring that the water reaches the desired temperature quickly and consistently, which is essential for high-quality coffee production.

In terms of usability, the Bunn CDS-3 offers an intuitive interface, allowing staff to operate it with minimal training. The front-access design not only simplifies maintenance, but also makes it easy to refill water and perform routine cleaning. Furthermore, the large capacity coffee pots ensure that the brewed coffee can be stored efficiently, minimizing waste.

Equipped with a unique spray head system, the Bunn CDS-3 ensures uniform saturation of the coffee grounds. This feature supports optimal extraction, allowing users to produce a rich and flavorful brew that keeps customers coming back for more.

In summary, the Bunn CDS-3 is a well-engineered, commercial-grade coffee brewer that excels in high-demand environments. Its robust construction, advanced brewing technology, consistent temperature control, and user-friendly design make it a favorite among coffee enthusiasts and professionals alike, affirming its reputation as a reliable and effective solution for coffee brewing needs. Whether for a bustling café or a catering service, the Bunn CDS-3 delivers a consistently great cup of coffee every time.
Top Page Image Contents