Bunn dispenser Whipper Motor, Install dispense tip into the bottom of the whipper chamber

Page 17

SERVICE (cont.)

WHIPPER MOTOR (cont.)

13.Slide the slinger onto the motor shaft flush against the front panel.

14.Wash whipper chamber components in a mild solution of dish detergent using a bristle brush.

15.Rinse thoroughly and allow to dry before reinstall- ing in the dispenser.

16.Slide whipper chamber receptacle with seal and O- ring onto the motor shaft.

17.Rotate the receptacle with seal counterclockwise until it snaps into place on the motor mounting nuts.

18.Push frother onto the motor shaft, making sure the flat in the frother lines up with the flat on the motor shaft.

19.Connect the red/black and green wires to the hop- per switch, Fig.10 and install the hopper support panel using the four #8-32 screws.

20.Install whipper chamber on the whipper chamber receptacle by twisting counterclockwise until tabs on the whipper chamber lock with the tabs on the whipper chamber receptacle. Be sure dispense port is pointing down.

BLK

WHI/RED to Control Board (J7-2)

WHI/BRN to Control Board (J7-4)

P1903

FIG. 9 WHIPPER MOTOR TERMINALS

21.Install dispense tip into the bottom of the whipper chamber.

22.Slip the mixing chamber onto the mixing chamber water inlet tube far enough so the mixing chamber will seat inside the whipper chamber.

23.Install hopper assembly in the dispenser by sliding hopper assembly on the hopper support panel until the slot in the bottom rear of the hopper seats against the pin and retainer plates on the hopper support panel.

GRN to Control Boad (J1-8)

RED/BLK to Control Board (J1-10)

P1904

FIG. 10 HOPPER SWITCH TERMINALS

17

29793.1 021202

 

Image 17
Contents Post Office BOX SPRINGFIELD, Illinois Bunn Powder Auto FillIntroduction BUNN-O-MATIC Commercial Product Warranty34561.0000 Initial SET-UPUser Notices Operating Instructions Adjustments Rinse and dry each item thoroughly before reas- sembling CleaningRecommended Daily Cleaning and Maintenance Tips Normal operation Powder Auto-Fill ready to Fault ListDispense Door not closedProblem Probable Cause TroubleshootingPowder Auto-Fill hopper not in- stalled properly ProblemRemedy Auger Drive Control Board and ProbeTransformer Water Strainer OptionalProblem Probable Cause Remedy Component Access ServiceHopper Lid Auger Drive ComponentsRetainer Clip Spacer Dust Seal Hopper BaseAuger Drive Motor Diagrams and check wiring harnessMixing Chamber Frother and MIXING/WHIPPER ChamberVolts ac for 120 volt models Volts ac for 230 volt CE models Whipper MotorWhipper Motor Install dispense tip into the bottom of the whipper chamberIf voltage is present as described, proceed to #9 If voltage is present as described, proceed to #5Test Procedure Low Product Detect Remove the control board Instal the new control board using the four #6-32 keps nutsLocation TEST/SERVICE SwitchDisconnect the wires from the switch terminals Main Power ON/OFF Switch Main Power ON/OFF SwitchRefer to when reconnecting the wires Lamp Cord AssemblyRemove new nut and washer from new lamp cord connector Lamp Cord ConnectorDisconnect the lamp cord from the lamp cord connector Close the dispenser door Lamp HOLDER/SOCKET AssemblyTransformer TransformerPotentiometer PotentiometerHopper Level Indicator Hopper Level IndicatorHopper Switch Hopper SwitchDoor Switch Door SwitchPressure Regulator and Needle Valve AdjustmentsDispense Solenoid Valve Location Dispense Solenoid ValveSchematic Wiring Diagram PAF Wiring DiagramsSchematic Wiring Diagram Pafa

dispenser specifications

The Bunn dispenser is a highly regarded name in the beverage service industry, known for its reliable coffee brewers, steeping equipment, and beverage dispensing solutions. These dispensers are designed with efficiency and quality in mind, making them a favorite in restaurants, cafes, and other foodservice establishments.

One of the main features of the Bunn dispenser is its rapid brewing capability. Utilizing a unique brewing system, Bunn dispensers can quickly brew large quantities of coffee, which is essential for high-demand environments. The machines are equipped with advanced heating technology that ensures water is brewed at the optimal temperature for extracting the best flavors from coffee grounds. This feature not only enhances the quality of the beverage but also significantly reduces waiting times for customers.

Another key characteristic of Bunn dispensers is their durability. Built with high-quality materials, these machines are designed to withstand the rigors of a busy kitchen environment. The robust construction ensures a long lifespan, minimizing the need for frequent repairs or replacements. Additionally, many models feature stainless steel components that are resistant to corrosion and easy to clean, maintaining hygiene standards while also looking professional.

Bunn dispensers are also known for their versatility. With a range of models available, including single and multi-hopper options, they can dispense various beverages, including coffee, tea, and iced drinks. This flexibility allows businesses to cater to different customer preferences without requiring multiple machines. Moreover, Bunn dispensers often come with programmable features, enabling users to customize brew strengths and volumes for optimal beverage consistency.

In terms of technology, Bunn has incorporated advanced digital controls and user interfaces in many of its models. These digital displays simplify operation, allowing staff to monitor brewing processes and receive alerts for maintenance requirements efficiently. Such technological integration enhances user experience and operational efficiency.

Energy efficiency is another consideration in the design of Bunn dispensers. Many models are equipped with energy-saving features, which help reduce power consumption during both operation and standby modes. This focus on sustainability not only lowers utility costs for businesses but also aligns with the growing consumer demand for environmentally responsible practices.

In conclusion, Bunn dispensers combine speed, durability, versatility, advanced technology, and energy efficiency, making them an excellent choice for any foodservice operation. Their ability to deliver high-quality beverages quickly and consistently makes them a pivotal asset for businesses aiming to provide an exceptional customer experience.