Bunn dispenser service manual Operating Instructions

Page 4

OPERATING INSTRUCTIONS

1.On the Ultra touch pad, make the following settings:

a)POWER- "ON"

b)DAY/NIGHT- "DAY"

2.Pull the Powder Auto-Fill fully forward on its sup- port rails and open the door.

3.Fill the Powder Auto-Fill product hopper as follows:

a)Pull the slide gate closed on the Powder Auto-Fill product hopper elbow and remove the hopper from the Powder Auto-Fill.

b)Remove the lid from the product hopper and fill the hopper with a powdered granita mix.

c)Install the product hopper into the Powder Auto- Fill. Insure hopper is fully seated behind retainer plates.

d)Push the slide gate on the hopper ejector elbow to the open position.

4.Place the ON/OFF switch at the Powder Auto-Fill whipper panel to "ON".

5.After allowing 5 seconds for the Powder Auto-Fill to initialize, observe the door lamp. The door lamp should not be lit. If the door lamp is lit, consult the fault list located on the decal placed on the back of the door. Clear the fault before proceeding.

NOTE: If the Powder Auto-Fill is being used for the first time with the selected granita mix, perform an adjust- ment as described in ADJUSTMENTS.

6.Close the Powder Auto-Fill door and observe the following:

a)The door lamp lights steadily.

b)The Powder Auto-Fill begins dispensing liquid granita product.

7.The Powder Auto-Fill will continue to fill the ULTRA product hopper until the liquid level in the ULTRA hopper reaches the product level probe or for 5 minutes, which ever occurs first.

8.If the Powder Auto-Fill fails to fill the ULTRA hopper in 5 minutes, the following will occur:

a)The Powder Auto-Fill will stop dispensing prod- uct.

b)The door lamp will flash 4 times about every 2 seconds.

9.After checking the ULTRA and Powder Auto-Fill set- up, the 5 minute refill fault may be cleared by simply opening and closing the Powder Auto-Fill door.

10.Once the product level in the ULTRA covers the auger, make the following switch settings at the ULTRA control panel:

a)AUGER - "1".

b)ICE/OFF/CHILL - "ICE" or "CHILL" as appropriate for the granita product.

11.From this point onward, the Powder Auto-Fill will continue to automatically refill the ULTRA hopper, maintaining the ULTRA product at an approximate 2 gallon level.

12.When the Powder Auto-Fill powder level falls low, the door lamp will cycle ON and OFF, but will continue to dispense product for a preset period. When this period expires, the Powder Auto-Fill will continue to cycle the door lamp ON and OFF and will stop dispensing product.

13.To clear the low product fault, simply refill the powder as follows:

a)Open the Powder Auto-Fill door.

b)Close the hopper slide gate.

c)Remove the product hopper.

d)Refill the product hopper with powdered granita mix.

e)Replace the hopper.

f)Push the slide gate on the hopper ejector elbow to the OPEN position.

g)Close the Powder Auto-Fill door.

4

29793.1 021202

 

Image 4
Contents Bunn Powder Auto Fill Post Office BOX SPRINGFIELD, IllinoisBUNN-O-MATIC Commercial Product Warranty IntroductionUser Notices Initial SET-UP34561.0000 Operating Instructions Adjustments Recommended Daily Cleaning and Maintenance Tips CleaningRinse and dry each item thoroughly before reas- sembling Fault List Normal operation Powder Auto-Fill ready toDispense Door not closedTroubleshooting Problem Probable CauseRemedy ProblemPowder Auto-Fill hopper not in- stalled properly Control Board and Probe Auger DriveTransformer Water Strainer OptionalProblem Probable Cause Remedy Service Component AccessAuger Drive Components Hopper LidRetainer Clip Spacer Dust Seal Hopper BaseDiagrams and check wiring harness Auger Drive MotorFrother and MIXING/WHIPPER Chamber Mixing ChamberWhipper Motor Volts ac for 120 volt models Volts ac for 230 volt CE modelsInstall dispense tip into the bottom of the whipper chamber Whipper MotorIf voltage is present as described, proceed to #5 If voltage is present as described, proceed to #9Test Procedure Low Product Detect Instal the new control board using the four #6-32 keps nuts Remove the control boardDisconnect the wires from the switch terminals TEST/SERVICE SwitchLocation Main Power ON/OFF Switch Main Power ON/OFF SwitchLamp Cord Assembly Refer to when reconnecting the wiresDisconnect the lamp cord from the lamp cord connector Lamp Cord ConnectorRemove new nut and washer from new lamp cord connector Lamp HOLDER/SOCKET Assembly Close the dispenser doorTransformer TransformerPotentiometer PotentiometerHopper Level Indicator Hopper Level IndicatorHopper Switch Hopper SwitchDoor Switch Door SwitchAdjustments Pressure Regulator and Needle ValveDispense Solenoid Valve Dispense Solenoid Valve LocationWiring Diagrams Schematic Wiring Diagram PAFSchematic Wiring Diagram Pafa

dispenser specifications

The Bunn dispenser is a highly regarded name in the beverage service industry, known for its reliable coffee brewers, steeping equipment, and beverage dispensing solutions. These dispensers are designed with efficiency and quality in mind, making them a favorite in restaurants, cafes, and other foodservice establishments.

One of the main features of the Bunn dispenser is its rapid brewing capability. Utilizing a unique brewing system, Bunn dispensers can quickly brew large quantities of coffee, which is essential for high-demand environments. The machines are equipped with advanced heating technology that ensures water is brewed at the optimal temperature for extracting the best flavors from coffee grounds. This feature not only enhances the quality of the beverage but also significantly reduces waiting times for customers.

Another key characteristic of Bunn dispensers is their durability. Built with high-quality materials, these machines are designed to withstand the rigors of a busy kitchen environment. The robust construction ensures a long lifespan, minimizing the need for frequent repairs or replacements. Additionally, many models feature stainless steel components that are resistant to corrosion and easy to clean, maintaining hygiene standards while also looking professional.

Bunn dispensers are also known for their versatility. With a range of models available, including single and multi-hopper options, they can dispense various beverages, including coffee, tea, and iced drinks. This flexibility allows businesses to cater to different customer preferences without requiring multiple machines. Moreover, Bunn dispensers often come with programmable features, enabling users to customize brew strengths and volumes for optimal beverage consistency.

In terms of technology, Bunn has incorporated advanced digital controls and user interfaces in many of its models. These digital displays simplify operation, allowing staff to monitor brewing processes and receive alerts for maintenance requirements efficiently. Such technological integration enhances user experience and operational efficiency.

Energy efficiency is another consideration in the design of Bunn dispensers. Many models are equipped with energy-saving features, which help reduce power consumption during both operation and standby modes. This focus on sustainability not only lowers utility costs for businesses but also aligns with the growing consumer demand for environmentally responsible practices.

In conclusion, Bunn dispensers combine speed, durability, versatility, advanced technology, and energy efficiency, making them an excellent choice for any foodservice operation. Their ability to deliver high-quality beverages quickly and consistently makes them a pivotal asset for businesses aiming to provide an exceptional customer experience.