Bunn dispenser service manual Adjustments

Page 5

ADJUSTMENTS

When using the Powder Auto-Fill with a new powdered granita mix, follow the procedure outlined below to adjust the Powder Auto-Fill to produce the correct recipe.

1.Determine the mix ratio of powdered granita mix. Convert the recipe so that it is expressed in terms of weight units [grams (g), dry ounces (oz), or pounds (lbs)] of powdered granita mix to fluid ounces (fl.oz.) of water [1 gallon (gal) = 128 fl.oz.; 1 liter (l) = 33.8 fl.oz.].

2.The delivery rate of the water ingredient is factory preset to 1 fl.oz. per second. Therefore, it is only necessary to adjust the delivery rate of the pow- dered granita mix. Adjustment is accomplished as follows:

a) Place the Powder Auto-Fill on top of a fully assembled ULTRA taking care to align the Powder Auto-Fill guide rails over the rollers on the platform guide rails.

b) Connect the Powder Auto-Fill power cord to the outlet located on the ULTRA auger motor cover. c) Attach a flexible water line to the .25" flare fitting on the back panel of the Powder Auto-Fill.

NOTE: A water strainer assembly (BUNN-O-MATIC #23820.1000) should be installed in line prior to the flexible water line.

d)On the ULTRA touch pad, make the following settings:

i)POWER- "ON"

ii)DAY/NIGHT- "DAY"

e)Pull the Powder Auto-Fill fully forward on its support rails

f)Fill the Powder Auto-Fill product hopper as fol- lows:

i)Pull the slide gate closed on the Powder Auto- Fill product hopper elbow and remove the product hopper from the Powder Auto-Fill.

ii)Remove the lid from the product hopper and fill the hopper with a powdered granita mix.

iii)Install the product hopper into the Powder Auto-Fill.

g)Place the ON/OFF switch at the Powder Auto-Fill whipper panel to "ON".

h)After allowing 5 seconds for the Powder Auto-Fill to initialize, observe the door lamp on the whipper panel. The door lamp should not be lit. If the door lamp is lit, consult the fault list and clear the fault before proceeding.

i)Remove the hole plug on the whipper panel. Using a screwdriver, set potentiometer to approxi- mately mid range.

j)Remove the mixing chamber from the Powder Auto-Fill and place a small container, such as a cup, under the product hopper ejector elbow.

k)Push the slide gate on the product hopper ejector elbow to the OPEN position.

l)Momentarily set the TEST/SERVICE switch on the whipper panel to the TEST position.

m)The hopper motor will run and dispense pow- dered granita mix for 10 seconds.

n)After the Powder Auto-Fill has finished the 10 second throw test, weigh the dispensed product.

o)Determine the dispense rate of the powdered product (weight units per second) by dividing the measured weight by 10.

p)Compare the measured dispense rate with the mix ratio in step 1.

q)Adjust the MIN/MAX control clockwise to in- crease the dispense rate or counterclockwise to decrease the dispense rate of the powdered granita mix.

r)Repeat steps l through q as necessary until proper mix ratio is achieved.

s)Replace the mixing chamber removed in step j. Replace hole plug.

3.Once the mix ratio has been adjusted, the Powder Auto-Fill can be run with the door open to allow the user to catch dispensed product for brix testing as follows:

a)Hold a container under the dispense tip of the Powder Auto-Fill.

b)Hold the TEST/SERVICE switch on the whipper panel to the SERVICE position.

c)When the container is filled to the desired level, release the TEST/SERVICE switch.

d)Measure the brix using the appropriate measur- ing device.

e)Remove the hole plug. Using a screwdriver, adjust the potentiometer clockwise to increase the brix or counterclockwise to decrease the brix of the product. Replace the hole plug.

5

29793.1 021202

 

Image 5
Contents Post Office BOX SPRINGFIELD, Illinois Bunn Powder Auto FillIntroduction BUNN-O-MATIC Commercial Product Warranty34561.0000 Initial SET-UPUser Notices Operating Instructions Adjustments Rinse and dry each item thoroughly before reas- sembling CleaningRecommended Daily Cleaning and Maintenance Tips Normal operation Powder Auto-Fill ready to Fault ListDispense Door not closedProblem Probable Cause TroubleshootingPowder Auto-Fill hopper not in- stalled properly ProblemRemedy Auger Drive Control Board and ProbeTransformer Water Strainer OptionalProblem Probable Cause Remedy Component Access ServiceHopper Lid Auger Drive ComponentsRetainer Clip Spacer Dust Seal Hopper BaseAuger Drive Motor Diagrams and check wiring harnessMixing Chamber Frother and MIXING/WHIPPER ChamberVolts ac for 120 volt models Volts ac for 230 volt CE models Whipper MotorWhipper Motor Install dispense tip into the bottom of the whipper chamberIf voltage is present as described, proceed to #9 If voltage is present as described, proceed to #5Test Procedure Low Product Detect Remove the control board Instal the new control board using the four #6-32 keps nutsLocation TEST/SERVICE SwitchDisconnect the wires from the switch terminals Main Power ON/OFF Switch Main Power ON/OFF SwitchRefer to when reconnecting the wires Lamp Cord AssemblyRemove new nut and washer from new lamp cord connector Lamp Cord ConnectorDisconnect the lamp cord from the lamp cord connector Close the dispenser door Lamp HOLDER/SOCKET AssemblyTransformer TransformerPotentiometer PotentiometerHopper Level Indicator Hopper Level IndicatorHopper Switch Hopper SwitchDoor Switch Door SwitchPressure Regulator and Needle Valve AdjustmentsDispense Solenoid Valve Location Dispense Solenoid ValveSchematic Wiring Diagram PAF Wiring DiagramsSchematic Wiring Diagram Pafa

dispenser specifications

The Bunn dispenser is a highly regarded name in the beverage service industry, known for its reliable coffee brewers, steeping equipment, and beverage dispensing solutions. These dispensers are designed with efficiency and quality in mind, making them a favorite in restaurants, cafes, and other foodservice establishments.

One of the main features of the Bunn dispenser is its rapid brewing capability. Utilizing a unique brewing system, Bunn dispensers can quickly brew large quantities of coffee, which is essential for high-demand environments. The machines are equipped with advanced heating technology that ensures water is brewed at the optimal temperature for extracting the best flavors from coffee grounds. This feature not only enhances the quality of the beverage but also significantly reduces waiting times for customers.

Another key characteristic of Bunn dispensers is their durability. Built with high-quality materials, these machines are designed to withstand the rigors of a busy kitchen environment. The robust construction ensures a long lifespan, minimizing the need for frequent repairs or replacements. Additionally, many models feature stainless steel components that are resistant to corrosion and easy to clean, maintaining hygiene standards while also looking professional.

Bunn dispensers are also known for their versatility. With a range of models available, including single and multi-hopper options, they can dispense various beverages, including coffee, tea, and iced drinks. This flexibility allows businesses to cater to different customer preferences without requiring multiple machines. Moreover, Bunn dispensers often come with programmable features, enabling users to customize brew strengths and volumes for optimal beverage consistency.

In terms of technology, Bunn has incorporated advanced digital controls and user interfaces in many of its models. These digital displays simplify operation, allowing staff to monitor brewing processes and receive alerts for maintenance requirements efficiently. Such technological integration enhances user experience and operational efficiency.

Energy efficiency is another consideration in the design of Bunn dispensers. Many models are equipped with energy-saving features, which help reduce power consumption during both operation and standby modes. This focus on sustainability not only lowers utility costs for businesses but also aligns with the growing consumer demand for environmentally responsible practices.

In conclusion, Bunn dispensers combine speed, durability, versatility, advanced technology, and energy efficiency, making them an excellent choice for any foodservice operation. Their ability to deliver high-quality beverages quickly and consistently makes them a pivotal asset for businesses aiming to provide an exceptional customer experience.