Bunn dispenser service manual Transformer

Page 26

SERVICE (cont.)

TRANSFORMER

P1930

FIG. 23 TRANSFORMER

Location:

The transformer is located under the hopper sup- port panel mounted to the left of the whipper motor.

Test Procedures:

1.Disconnect the dispenser from the power source.

2.Disconnect the four pin connector from the main wiring harness from the four pin connector on the transformer.

3.Check the voltage across the black wire (pin 1) and the white wire (pin 2) on the plug from the main wiring harness. Connect the dispenser to the power source. The indication must be:

a)120 volts ac for 120 volt models.

b)230 volts ac for 230 volt CE models.

4.Disconnect the dispenser from the power source.

If voltage is present as described, reconnect the plug and the connector and proceed to #5.

If voltage is not present as described, refer to the wiring diagrams and check the main wiring harness.

5.Check the voltage between J1-2 and J1-3 on the twelve pin connector at the control board. Connect the dispenser to the power source. The indication must be 24 volts ac.

If voltage is present as described, the transformer is operating properly.

If voltage is not present as described, replace the transformer.

Removal and Replacement:

1.Remove the hopper from the dispenser.

2.Remove the four #8-32 screws securing the hopper support panel to the dispenser.

3.Disconnect the red/black and green wires from the hopper switch and set the hopper support panel aside.

4.Disconnect the transformer four pin connector from the four pin plug on the main wiring harness.

5.Remove the two #6-32 keps nuts securing the transformer to the dispenser base. Remove and discard the transformer.

6.Install the new transformer on the dispenser base and secure with two #6-32 keps nuts.

7.Connect the four pin connector on the transformer to the four pin plug on the main wiring harness.

8.Reconnect the red/black and green wires to the hopper switch. See Fig. 10 on page 17.

9.Install the hopper support panel and secure with four #8-32 screws.

10.Install the hopper assembly.

26

29793.1 021202

 

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Bunn Powder Auto Fill Post Office BOX SPRINGFIELD, IllinoisBUNN-O-MATIC Commercial Product Warranty Introduction34561.0000 Initial SET-UPUser Notices Operating Instructions Adjustments Rinse and dry each item thoroughly before reas- sembling CleaningRecommended Daily Cleaning and Maintenance Tips Dispense Fault ListNormal operation Powder Auto-Fill ready to Door not closedTroubleshooting Problem Probable CausePowder Auto-Fill hopper not in- stalled properly ProblemRemedy Transformer Control Board and ProbeAuger Drive Water Strainer OptionalProblem Probable Cause Remedy Service Component AccessRetainer Clip Auger Drive ComponentsHopper Lid Spacer Dust Seal Hopper BaseDiagrams and check wiring harness Auger Drive MotorFrother and MIXING/WHIPPER Chamber Mixing ChamberWhipper Motor Volts ac for 120 volt models Volts ac for 230 volt CE modelsInstall dispense tip into the bottom of the whipper chamber Whipper MotorIf voltage is present as described, proceed to #5 If voltage is present as described, proceed to #9Test Procedure Low Product Detect Instal the new control board using the four #6-32 keps nuts Remove the control boardLocation TEST/SERVICE SwitchDisconnect the wires from the switch terminals Main Power ON/OFF Switch Main Power ON/OFF SwitchLamp Cord Assembly Refer to when reconnecting the wiresRemove new nut and washer from new lamp cord connector Lamp Cord ConnectorDisconnect the lamp cord from the lamp cord connector Lamp HOLDER/SOCKET Assembly Close the dispenser doorTransformer TransformerPotentiometer PotentiometerHopper Level Indicator Hopper Level IndicatorHopper Switch Hopper SwitchDoor Switch Door SwitchAdjustments Pressure Regulator and Needle ValveDispense Solenoid Valve Dispense Solenoid Valve LocationWiring Diagrams Schematic Wiring Diagram PAFSchematic Wiring Diagram Pafa

dispenser specifications

The Bunn dispenser is a highly regarded name in the beverage service industry, known for its reliable coffee brewers, steeping equipment, and beverage dispensing solutions. These dispensers are designed with efficiency and quality in mind, making them a favorite in restaurants, cafes, and other foodservice establishments.

One of the main features of the Bunn dispenser is its rapid brewing capability. Utilizing a unique brewing system, Bunn dispensers can quickly brew large quantities of coffee, which is essential for high-demand environments. The machines are equipped with advanced heating technology that ensures water is brewed at the optimal temperature for extracting the best flavors from coffee grounds. This feature not only enhances the quality of the beverage but also significantly reduces waiting times for customers.

Another key characteristic of Bunn dispensers is their durability. Built with high-quality materials, these machines are designed to withstand the rigors of a busy kitchen environment. The robust construction ensures a long lifespan, minimizing the need for frequent repairs or replacements. Additionally, many models feature stainless steel components that are resistant to corrosion and easy to clean, maintaining hygiene standards while also looking professional.

Bunn dispensers are also known for their versatility. With a range of models available, including single and multi-hopper options, they can dispense various beverages, including coffee, tea, and iced drinks. This flexibility allows businesses to cater to different customer preferences without requiring multiple machines. Moreover, Bunn dispensers often come with programmable features, enabling users to customize brew strengths and volumes for optimal beverage consistency.

In terms of technology, Bunn has incorporated advanced digital controls and user interfaces in many of its models. These digital displays simplify operation, allowing staff to monitor brewing processes and receive alerts for maintenance requirements efficiently. Such technological integration enhances user experience and operational efficiency.

Energy efficiency is another consideration in the design of Bunn dispensers. Many models are equipped with energy-saving features, which help reduce power consumption during both operation and standby modes. This focus on sustainability not only lowers utility costs for businesses but also aligns with the growing consumer demand for environmentally responsible practices.

In conclusion, Bunn dispensers combine speed, durability, versatility, advanced technology, and energy efficiency, making them an excellent choice for any foodservice operation. Their ability to deliver high-quality beverages quickly and consistently makes them a pivotal asset for businesses aiming to provide an exceptional customer experience.
Top Page Image Contents