Bard QC501 Qtec Energy Recovery Ventilator Option, Removal of the Qtec Energy Recovery Ventilator

Page 15

QTEC ENERGY RECOVERY VENTILATOR OPTION

Before starting the removal make sure that the power has been turned off. The hinged return air grille panel must be opened. The energy recovery ventilator (QERV) can be seen after the panel is opened. To gain access to the mist eliminator, the QERV must be removed. Refer to Figure 11

1.The front fill plate of the QERV must be removed. There is one screw on either side of the plate. Remove these screws and remove the plate.

2.On either side of the QERV there are mounting screws that hold the QERV in place. Remove both of these screws.

3.Underneath the heat recovery cassette there is a power connector for the lower blower assembly. To disconnect this plug, the tabs on both sides of the plug must be squeezed to release the plug. While squeezing the tabs, pull the plug out of the socket.

4.The QERV is plugged into the unit on the right side of the unit. Both of these plugs must be disconnected to remove the QERV. Squeeze the tabs on the sides of the connector and pull straight out.

5.Slide the QERV assembly straight out of the unit being careful not to let the cassette slide out of the QERV.

The mist eliminator can be seen through the opening in the back of the unit. The mist eliminator must be raised up and the bottom can be pulled toward the front of the unit and removed.

FIGURE 11

REMOVAL OF THE QTEC ENERGY RECOVERY VENTILATOR

POWER

CONNECTORS

MOUNTING

SCREWS

LOWER BLOWER

ASSEMBLY POWER

CONNECTOR

FRONT FILL

MIS-1605

Manual 2100-416

Page 13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model QC501 QC Series Installation Chilled Water Unit InstructionsContents For More INFORMATION, Contact These Publishers Getting Other Information and PublicationsFactory BUILT-IN Electric Heat Table Electrical SpecificationsQC Series Water Source General Information QC Model NomenclaturePsig Cooling Performance ChartUnit Dimensions Shipping Damage Unit Removal from SkidHandling Unit After Removal from Skid Proper Handling of Unit After Removal from Skid Minimum Installation HeightRemoval of Wall Bracket from Shipping Location GeneralInstallation of Unit Thru Wall with Wall Sleeve Ducted Application Installation with Free Blow PlenumFilter Location Duct WorkFilters Supply Duct ConnectionsOptional Rear Drain Condensate DrainSide Drain Side View Rear Drain TOP ViewCommercial Room Ventilator Option Barometric Fresh AIR Damper OptionalFresh AIR Damper Removal Removal of the Qtec Energy Recovery Ventilator Qtec Energy Recovery Ventilator OptionInstallation Instructions Mounting the UnitRemoving Locking Screws from Wheels Side Trim Pieces Wall Mounting Bracket Component Location Wiring Main PowerWall Thermostats and Subbase Combinations Wiring LOW Voltage WiringFluid Connections Operating Voltage RangeBlower Motor LOW Voltage Wire Harness Plug LOW Voltage ConnectionsLOW Voltage Connections for DDC Control Remote Thermostat Wiring Diagram Option Remote Thermostat Wiring Diagram Thermostat Option Optional CFM Important Installer NoteService Hints Start UPSymptom Troubleshooting ECM Blower MotorsSymptom Internal 2-WAY Valve Piping Valve DetailInternal 3-WAY Valve Piping

QC501 specifications

The Bard QC501 is an innovative piece of equipment designed specifically for quality control in various manufacturing processes. Known for its precision and efficiency, the QC501 serves multiple industrial sectors, including pharmaceuticals, food and beverage, cosmetics, and chemical manufacturing.

One of the standout features of the Bard QC501 is its state-of-the-art measurement technology. It utilizes advanced sensors and automated systems to ensure highly accurate readings. This precision is critical for industries where even the smallest deviation can result in significant issues, such as compromised product safety or regulatory violations.

The QC501 incorporates a user-friendly interface that simplifies operation for technicians and quality control personnel. Its touchscreen display provides real-time data, allowing users to monitor processes effectively and make on-the-fly adjustments as needed. This responsiveness ensures that production standards are consistently met, enhancing overall efficiency.

Another notable characteristic of the Bard QC501 is its data logging capabilities. The device is equipped with comprehensive software that records, analyzes, and generates reports on quality metrics. This feature is invaluable for facilitating thorough audits and maintaining compliance with stringent industry regulations. By providing a digital trail of quality data, the QC501 empowers companies to demonstrate their commitment to quality assurance.

In terms of connectivity, the QC501 is designed to integrate seamlessly into existing production lines. It offers multiple connectivity options, such as Ethernet and USB ports, making it compatible with various systems. This flexibility allows businesses to enhance their existing quality control processes without a complete overhaul of their infrastructure.

Durability is another critical aspect of the QC501. Manufactured with robust materials, it is designed to withstand the rigors of industrial environments. This reliability reduces downtime due to equipment failure, ensuring that production schedules remain on track.

In summary, the Bard QC501 stands out for its precision measurement technology, user-friendly interface, comprehensive data logging, seamless connectivity, and rugged durability. This combination of features makes it an essential tool for industries striving to maintain high quality standards while optimizing production efficiency. Investing in the Bard QC501 is a proactive step toward enhancing overall product quality and ensuring compliance with regulatory standards.
Top Page Image Contents