Power Cord Installation, Battery Installation

Installation Instructions

FAUCET ASSEMBLY (cont.)

OPTIONAL ONE PERSON FAUCET TUBING INSTALLATION

1.From under the sink, gather the 1/4″ drain line (black), 3/8″ drain line (black) and 3/8″ outlet tube (blue banded) in one hand with the drain tubes the same length and the outlet tube offset approximately 6 inches.

2.Wrap a rubber band around all 3 tubes.

3.Insert a typical No. 2 pencil through the rubber band location.

4.Rotate the pencil down until it is in line with the tubing and push up through the mounting hole. Release the grip on the pencil and the tubes will remain in position for easier faucet connection.

POWER CORD INSTALLATION

Connect power cord from faucet to union outlet from the Reverse Osmosis Assembly.

NOTE: If extension cord is required for a remote

location, this extension

phone cable must be 6 conductor wire and connectors; typical 4 conductor will not work.

BATTERY INSTALLATION

1.Use a small flat blade screwdriver or coin to remove the battery tray (A) at the side of the faucet base.

2.Install one CR2032, 3 volt battery (B) positive “+” side down into the battery tray (A).

3.Slide tray into faucet base (C) until the battery tray (A) edge is flush with the side of the base.

4.Each light will illuminate in sequence twice. At the end, the OK (green) light or filter (yellow) light may stay on for a few extra seconds. If you want to reinitiate the start-up sequence, remove the battery for 90 seconds; the electronics need to fully discharge. Then put the battery back in.

5.The OK (green) light will normally flash one time per second when dispensing water. The filter or RO (amber) lights will flash one time per second when dispensing water if the system needs service. If the system needs service, they will also flash randomly when the system is not in use.

For lights to change between OK and RO, the system must detect a change in the filtering process for 25 consecutive seconds. For example, if the system was not filtering correctly, the RO light would be flashing. When the problem is corrected and the system is filtering correctly, the electronics will wait for 25 seconds to confirm the changes before changing to an OK light.

(D)Green or

amber lights	(B) Battery
amber lights
	–
	+
(C) Faucet base	(A) Battery
	tray

FOR FILTER CHANGE: Replace battery when changing filter. Remove used battery and wait at least 90 seconds before installing new battery. This will ensure full electronic reset and proper operation for the next 6 months.

PNRQ21LRB, PNRQ21LBN specifications

The GE PNRQ21LBN and PNRQ21LRB are two advanced models from General Electric's line of innovative HVAC (Heating, Ventilation, and Air Conditioning) solutions. Designed with both efficiency and performance in mind, these units cater to residential and commercial needs, ensuring comfort in a variety of settings.

One of the standout features of the PNRQ21LBN and PNRQ21LRB is their energy efficiency. Both models utilize GE's cutting-edge inverter technology, which allows for variable speed operation. This means that the compressor can adjust its output based on the specific cooling or heating needs, leading to significant energy savings while maintaining optimal indoor climates. As a result, these units are not only environmentally friendly, but also cost-effective over time.

Another key characteristic is their quiet operation. The engineers at GE have invested in sound-dampening technologies that minimize operational noise, allowing users to enjoy a peaceful atmosphere, whether in a home, office, or commercial space. This is particularly beneficial for areas where noise sensitivity is crucial, such as bedrooms or conference rooms.

The PNRQ21LBN and PNRQ21LRB also come equipped with advanced air filtration systems. These systems effectively remove dust, allergens, and other airborne particles, contributing to improved indoor air quality. The filters are easily accessible for maintenance, ensuring that users can keep their systems running at peak performance with minimal effort.

User-friendly interfaces are another hallmark of these GE models. They feature intuitive control options that allow users to set schedules, adjust temperature preferences, and even monitor energy usage. This level of control empowers users to optimize their HVAC systems according to their lifestyle and needs.

In terms of design, both models boast a sleek and modern aesthetic, making them suitable for various architectural styles. They can fit seamlessly into any environment, enhancing the overall appeal of the space.

Overall, the GE PNRQ21LBN and PNRQ21LRB exemplify a blend of efficiency, quiet operation, advanced filtration, and user-centric design, making them ideal choices for anyone looking to enhance comfort and improve energy efficiency in their living or working environments.