Feed Water Supply, Preferred Installation

Installation Instructions

FEED WATER SUPPLY

Check and comply with local plumbing codes as you plan, then install a cold feed water supply fitting.

A. PREFERRED INSTALLATION

Utilizing existing kitchen sink water supply valve (A) and removable faucet tubing (B).

1.Refer to illustration below to complete assembly depending on supply valve size (A).

2.Close the cold water supply valve (A) under the sink.

3.Unscrew the flexible tubing line (B) from the supply valve (A) that connects to the COLD water riser.

NOTE: For rigid pipe, see C. Optional Installation on page 10.

Note Adapter (C) orientation:

3/8-inch installation—Rounded end of adapter

1/2-inch installation—Rounded end of adapter

(C)connects to coupling (D), then to existing faucet tubing (B).


For 3/8″ Plumbing			For 1/2″ Plumbing

4.Assemble adapter (C) and coupling (D) as shown in illustration at left, per your configuration. Ensure that the gasket (G) is in place before final assembly. Start installation by hand, then finish tightening with adjustable wrench. Be careful not to overtighten or cross thread as damage to threads may occur.

5.Hand tighten assembled adapter (C) onto supply valve (A) for the proper size installation. Be sure gasket (G) is in place before final assembly. Start installation by hand, then finish tightening with an adjustable wrench. Be careful not to overtighten or cross thread as damage to threads may occur.

6.Reconnect faucet tubing line (B) to top of adapter (C).

NOTE: If inlet valve (F) is to be removed for installation, refer to E. Removal and Reinstallation of Inlet Valve on page 11.

7. Cut wire ties on tubing coils, using care

not to damage tubes or parts if using a

utility knife.

8. Remove the 1/2″ nut (I) and ferrule (H)

from end of inlet valve. Using the yellow

banded tubing provided, place the nut (I)

and ferrule (H) onto the tubing and install

onto inlet valve (F) as shown at left.

Tighten with adjustable wrench. Be

careful not to overtighten or cross thread

(G)

Gasket

(B)Faucet tubing line (not

included)	(H)
	Ferrule

(D)

Coupling

Adapter

(I) Nut

(F) Inlet valve

(G) Gasket

(A)Cold water supply valve (not included)

(B) Faucet

tubing line (not included)

(D)

Coupling

(G) Gasket

(C)

Adapter

(A)Cold water supply valve (not included)

as damage to threads may occur.

NOTE: Inspect the ends of the tubing prior to installation to be sure there are no imperfections and that the end of the tubing is cut square. It may be necessary to cut the tubing again.

PNRQ21LRB, PNRQ21LBN specifications

The GE PNRQ21LBN and PNRQ21LRB are two advanced models from General Electric's line of innovative HVAC (Heating, Ventilation, and Air Conditioning) solutions. Designed with both efficiency and performance in mind, these units cater to residential and commercial needs, ensuring comfort in a variety of settings.

One of the standout features of the PNRQ21LBN and PNRQ21LRB is their energy efficiency. Both models utilize GE's cutting-edge inverter technology, which allows for variable speed operation. This means that the compressor can adjust its output based on the specific cooling or heating needs, leading to significant energy savings while maintaining optimal indoor climates. As a result, these units are not only environmentally friendly, but also cost-effective over time.

Another key characteristic is their quiet operation. The engineers at GE have invested in sound-dampening technologies that minimize operational noise, allowing users to enjoy a peaceful atmosphere, whether in a home, office, or commercial space. This is particularly beneficial for areas where noise sensitivity is crucial, such as bedrooms or conference rooms.

The PNRQ21LBN and PNRQ21LRB also come equipped with advanced air filtration systems. These systems effectively remove dust, allergens, and other airborne particles, contributing to improved indoor air quality. The filters are easily accessible for maintenance, ensuring that users can keep their systems running at peak performance with minimal effort.

User-friendly interfaces are another hallmark of these GE models. They feature intuitive control options that allow users to set schedules, adjust temperature preferences, and even monitor energy usage. This level of control empowers users to optimize their HVAC systems according to their lifestyle and needs.

In terms of design, both models boast a sleek and modern aesthetic, making them suitable for various architectural styles. They can fit seamlessly into any environment, enhancing the overall appeal of the space.

Overall, the GE PNRQ21LBN and PNRQ21LRB exemplify a blend of efficiency, quiet operation, advanced filtration, and user-centric design, making them ideal choices for anyone looking to enhance comfort and improve energy efficiency in their living or working environments.