Hoshizaki MWH KML-451MAH, MRH, KML-250MAH II. Installation and Operating Instructions, Location

Page 12

II. Installation and Operating Instructions

WARNING

•The appliance must be installed in accordance with applicable national, state, and local codes and regulations.

•Failure to install, operate, and maintain the appliance in accordance with this manual will adversely affect safety, performance, component life, and warranty coverage and may result in costly water damage.

•CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews

are securely in place after installation. Make sure that none have fallen into the dispenser unit/ice storage bin.

A. Location

NOTICE

•The icemaker is not intended for outdoor use. Normal operating ambient temperature must be within 45°F to 100°F (7°C to 38°C); Normal operating water temperature must be within 45°F to 90°F (7°C to 32°C). Operation of the icemaker, for extended periods, outside of these normal temperature ranges may affect icemaker performance.

•The icemaker will not work at sub-freezing temperatures. To prevent damage

to the water supply line, drain the icemaker if the air temperature is going to go below 32°F (0°C). See "IV. Preparing the Icemaker for Periods of Non-Use."

•The icemaker should not be located next to ovens, grills, or other high heat producing equipment.

•Allow 6" (15 cm) clearance at rear, sides, and top for proper air circulation and ease of maintenance and/or service should they be required.

•The location should provide a firm and level foundation for the appliance.

B. Checks Before Installation

•Visually inspect the exterior of the shipping container and immediately report any damage to the carrier. Upon opening the container, any concealed damage should also be immediately reported to the carrier.

•Remove the shipping carton, tape, and packing material. If any are left in the appliance, it will not work properly.

•See the nameplate on the rear panel, and check that your voltage supplied corresponds with the voltage specified on the nameplate.

•Remove the panels to prevent damage when installing the appliance. See "II.C. How to Remove Panels."

•Remove the package containing the accessories.

•Remove the protective plastic film from the panels. If the appliance is exposed to the sun or to heat, remove the film after the appliance cools.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents KML-631MAH, MWH, MRH Hoshizaki AMERICA, INC Contents Important Safety Information Serious injuryIndicates a situation which could result in damage to Appliance or propertyAdditional Warning for Remote Models Specifications Electrical and Refrigerant Data KML-250MHKML-351MH KML-451MH KML-631MHDimensions/Connections Air-Cooled Models MAH Units mmWater-Cooled Models MWH Units mmRemote Models MRH Remote Condenser Unit URC-9F use with KML-631MRH II. Installation and Operating Instructions Checks Before InstallationLocation How to Remove Panels See Fig Setup Dispenser Unit/Ice Storage Bin and Icemaker SetupIntentionally Left Blank Electrical Connection For All ModelsAdditional Warnings for Remote Models  WARNING Water Supply and Drain Connections See Figs through Air-Cooled and Remote Models IcemakerWater-Cooled Models Connection to an Open Drain SystemWater-Cooled Models Connection to a Closed Loop System Water-Cooled Models Model Shown KML-631MWH Installation of Remote Condenser Unit LocationChecks Before Installation SetupLine Set Size and Refrigerant Charge Line Set Installation Factory Line Set InstallationField Fabricated Line Set Installation Do not USE Thread Sealant Electrical Connection Stacking Remote Condenser Unit Final Checklist Startup Additional Notice for Remote ModelsIII. Maintenance Maintenance ScheduleCleaning and Sanitizing Instructions Cleaning ProcedureSanitizing Procedure Following Cleaning Procedure Page IV. Preparing the Icemaker for Periods of Non-Use Remove the water from the icemaker water supply lineDrain the water tank Page Disposal Hoshizaki AMERICA, INC
Related manuals
Manual 28 pages 29.45 Kb Manual 94 pages 41.69 Kb

MWH KML-351MAH, KML-250MAH, MWH KML-631MAH, MWH, MRH specifications

The Hoshizaki KML-250MAH is a premium ice maker renowned for its innovative design and advanced technology, catering to the high-demand needs of commercial establishments. This model combines efficiency, reliability, and superior performance, making it an excellent choice for restaurants, bars, and hotels.

One of the standout features of the KML-250MAH is its high production capacity. This ice maker can produce up to an impressive 265 pounds of crescent ice daily, ensuring your establishment has a consistent supply of ice for beverages and food preservation. The crescent-shaped ice not only allows for optimal cooling but also enhances presentation, making it suitable for a variety of applications.

The KML-250MAH incorporates advanced technologies to promote efficient operation. The unit uses an air-cooled refrigeration system, which ensures better energy efficiency while reducing operational costs. The machine is designed with a dual condensing fan that effectively optimizes airflow, thereby ensuring consistent ice production in different ambient temperatures, which is crucial in varying commercial kitchen environments.

The durability of this model is another key characteristic. Constructed with stainless steel, the KML-250MAH is built to withstand the rigors of daily commercial use while resisting rust and corrosion. The heavy-duty components used in this ice maker enhance its longevity, making it a smart investment for any business.

In addition, the KML-250MAH is designed with user-friendly features, including a built-in cleaning cycle that simplifies maintenance and ensures hygiene. Its ergonomic control panel provides users with easy access to settings and operational status, enhancing the overall user experience.

Another noteworthy aspect of the Hoshizaki KML-250MAH is its reduced water consumption. This ice maker operates using significantly less water compared to competitors, contributing to a lower environmental impact and cost savings over time.

To sum up, the Hoshizaki KML-250MAH stands out with its high production capacity, robust stainless steel construction, efficient air-cooled technology, user-friendly operation, and eco-conscious design. These features make it an ideal choice for businesses seeking a reliable and high-performing ice-making solution that meets the demands of a bustling commercial environment.
Top Page Image Contents