Henny Penny 600, 500 GAS Pilot & Burner Lighting and Shut Down Procedures, Shutdown Procedure

Page 18

2-9. GAS PILOT & BURNER LIGHTING AND SHUT DOWN PROCEDURES (Continued)

2-10

Model 500/600

Lighting Procedure - Solid State Ignition

1.The gas valve knob has a dual function.

a.Complete control of gas to the pilot and main burner.

b.When in the pilot position, it is the reset mechanism for the automatic pilot.

2.Partially press and turn the gas valve knob to the OFF position.

3.Wait at least 5 minutes to allow any gas to escape that may have accumulated in the burner compartment.

4.Turn the COOK/PUMP switch to OFF.

5.Turn the gas valve knob to the PILOT position.

6.Press and hold the gas valve knob while lighting the pilot. Allow the pilot to burn about 30 seconds before releasing the knob.

If the pilot does not stay lit, repeat steps 5 and 6, allowing a longer period of time before releasing the gas valve knob.

7.Turn the gas valve knob to the ON position.

8.Turn the COOK/PUMP switch to COOK.

9.With the lid open, select a product on control panel, and listen for the gas burner ignition (no longer than 10 seconds) and then turn COOK/PUMP switch OFF.

Do not leave unit on, without peanut oil, for more than 10 seconds or damage to the frypot could result.

10.Clean the frypot per the instructions in the Cleaning the Frypot Section.

11.Fill the frypot with peanut oil to the proper level.

12.The fryer is now ready for operation.

The pilot flame is preset at the factory. If adjustment is neces- sary, contact your local independent Henny Penny distributor.

Shutdown Procedure

1.Turn main power switch to OFF.

2.Depress the gas control valve knob lightly and turn to the OFF position.

806

Page 17 Page 19
Image 18
Page 17 Page 19
Contents OPERATOR’S Manual Page Keep appliance area free and clear from combustibles Model 500/600 Table of Contents Limit StopAdjustment Introduction Proper Care Assistance Safety Installation UnpackingInstructions Close the front door Unpacking Instructions Selecting the Fryer LocationSelecting the Fryer Location Leveling the Fryer Ventilation of FryerVentilation 0F Fryer GAS Supply GAS Leak Test Model 500/600 303 Lighting Procedure Solid State Ignition Shutdown ProcedureGAS Pilot & Burner Lighting and Shut Down Procedures Shutdown ProcedureRegulator AdjustmentPressure GAS only ElectricalSupply Wiring and Fusing for Electric Fryer Min Wire Fuse Phase Amps SizeElectrical Requirements Electric Fryer Frypot Lid Gasket Deadweight Assembly Safety Relief Valve Operation Operating ComponentsModel 500/600 Operating Components High Limit Description Function Operating Controls Control DecalClock SET Twice. Clock SET thenClock SET Diagnostic Mode Special Functions Peanut Oil Life FunctionLanguage Selection Status Mode Diagnostic Mode SpecialFunctions Manual Mode Peanut Oil Filter EnforcementInformation Mode FunctionsDisplay Cause Correction Error Messages Error CodesError Codes Filling or Adding Peanut OIL Electric ModelFilling or Adding Gas ModelPeanut OIL Basic Operation 803 Basic Operation Care of Peanut OIL Filtering ShorteningUse caution to prevent burns caused by splashing hot Filter Pump Problem Prevention Filtering of ShorteningFilter Pump Motor Thermal Protector Changing the Filter EnvelopeChanging the Filter Envelope Cleaning Frypot Cleaning the Frypot Cleaning the Frypot NEW or Used CleaningFrypot Fryer FunctionProcedure Frequency Preventive MaintenanceMaintenance ScheduleCleaned as follows Cleaning the DeadWeight Valve StepRemoval Cleaning Safety Relief Valve Gasket Temperature ProbeReversing LID CheckingLimit Stop Adjustment Lubricate LID Spindle and Ball Seat Check & Tighten Element Spreader Bars Model 500 only Page Troubleshooting Problem Cause Correction Cooking SectionProblem Cause Correction Cooking Section Problem Cause Correction Cooking Section Problem Cause Correction Cooking Section Power Section Pressure SectionProblem Cause Correction Pressure Section Filter System SectionProblem Cause Correction Filter System Section Heating of Peanut OilsectionProblem Cause Correction Heating of Peanut Oilsection COILS, ContactorsDiagnostic Mode DIAGNOSTIC* *REPORTDetails Diagnostic Mode Details ColorAdjustmentOil Wear Report D2 this OIL isLine Voltage Performance Report DetailsVoltage Report for Today Voltage Report for Present Batch of Peanut Oil D3 Warnings D3 on this OIL Details Following sequence is displayedD3 Before Today D3 MIN Voltage D3 Before TodayDetails Following report is displayed D4 Appear OK D4 Contactors D4 Connections D4 and WiringD4 Heater Coils D5 Cook Times D5 Look OK D5 TodayD5 Cooking Slow D5 Today D5 Detected D5 PossibleD5 Oversized D5 or Frozen D5 Batch D5 Possible D5 Oversized D5 BatchD6 Last OIL D6 Cooked D6 Before Ready D6 Before Today D6 Cooked D6 Before ReadyD6 on this OIL D7 Were Stopped D7 TOO Soon D7 TodayD7 Last OIL D7 Before TodayD7 Were Stopped D7 TOO Soon D7 on this OIL D7 Were Stopped D7 TOO SoonD8 Last OIL D8 Before TodayD8 Beeped ‘DONE’ D8 TOO Long D8 on this OIL D8 Beeped ‘DONE D8 TOO LongD9 Loading D9 Looks OK D9 this OIL D9 Loading D9 Looks OK D9 TodayD9 Irregular D9 Loading D9 for this OIL D9 Irregular D9 LoadingD9 Previous OIL D9 Irregular D9 Loading Loading Report for Previous Batch of Peanut oilD9 Loading D9 Looked OK D9 Previous OIL 10ALLPROD’SDo not Match ORIG. VALUES’ Do not Match ORIG. Values10ALL Cfaitems 10ALL SP ItemsInformation Mode ALL HC ItemsInformation Mode Details Function DisplayexampleFunction Displayex 5G. Slow HT’SPrev DAY SUN DAY Totals OIL Data current batch resets by Clean-Out Mode Began MAR-9 INP Avhdsfm POT TMP Analog 1 Model 500/600 O S S a R Y Shortening level also referred to as level indictor lines Head fryers. the lid assembly includes spindles Place see lid latch Gas fryers only See ignition modules Gas ElectricLimited Warranty for Henny Penny Equipment Henny Penny Corporation
Related manuals
Manual 66 pages 6.22 Kb

500, 600 specifications

Henny Penny has established itself as a leading name in the commercial cooking equipment industry, particularly known for its innovative fryers and cooking solutions. Among its notable products are the Henny Penny 500 and 600 series, which embody the brand's commitment to efficiency, reliability, and advanced technology.

The Henny Penny 500 series is designed for high-volume operations, perfect for restaurants, fast-food chains, and other foodservice establishments that require exceptional frying performance. This series features a highly efficient airflow design that ensures even cooking and reduces energy consumption. With a stainless-steel counter design, the Henny Penny 500 not only looks appealing but also offers durability and ease of cleaning, essential for maintaining hygiene in a busy kitchen.

One of the standout technologies in the 500 series is the advanced filtration system. This system helps to prolong oil life, reducing the frequency of oil replacements, which can save money and minimize waste. The intuitive control panel allows operators to manage cooking times and temperatures easily, resulting in consistent food quality. Additionally, the automatic basket lift feature enhances safety by reducing the chances of accidents during frying.

The Henny Penny 600 series takes this innovation further with additional features aimed at maximizing productivity. It shares many similarities with the 500 series but includes upgraded digital controls that allow for precise temperature management and programming options for various menu items. This added flexibility provides operators the ability to multitask effectively in a fast-paced kitchen environment.

Both series prioritize energy efficiency, with the 600 series particularly noted for its ability to minimize energy consumption without compromising performance. The fryers’ design incorporates energy-efficient heating elements and advanced insulation technology, ensuring quick recovery times and lower operating costs.

Furthermore, Henny Penny has incorporated user-friendly maintenance features in both series, such as easy-access panels for cleaning and routine maintenance checks. By focusing on operational ease and performance efficiency, the 500 and 600 series fryers exemplify Henny Penny’s dedication to providing commercial kitchens with the tools they need to succeed.

In summary, the Henny Penny 500 and 600 series reflect a blend of advanced technology and practical design, making them invaluable assets in any high-volume foodservice operation. With features such as high-efficiency frying, easy maintenance, and operator-centric controls, they stand as testaments to Henny Penny’s innovation in commercial cooking solutions.
Top Page Image Contents