Manitowoc Ice S0850M manual Water Dump Valve, Dump Valve Disassembly

Page 31

Section 4

Maintenance

 

 

Water Dump Valve

The water dump valve normally does not require removal for cleaning. To determine if removal is necessary:

1.Locate the water dump valve.

2.Set the toggle switch to ICE.

3.While the ice machine is in the freeze mode, check the dump valve’s clear plastic outlet drain hose for leakage.

A.If the dump valve is leaking, remove, disassemble and clean it.

B.If the dump valve is not leaking, do not remove it. Instead, follow the “Cleaning Procedure”.

Follow the procedure below to remove the dump valve.

Important

The plunger and the inside of the enclosing tube must be completely dry before assembly.

NOTE: During cleaning, do not stretch, damage or remove the spring from the plunger. If it is removed, slide the spring’s flared end into the plunger’s slotted top opening until the spring contacts the plunger spring stop.

5.Remove the valve body.

6.Remove the tubing from the dump valve by twisting the clamps off.

7.Remove the two screws securing the dump valve and the mounting bracket.

!Warning

CAP

PLUNGER SPRING STOP

Disconnect the electric power to the ice machine at the electric service switch box and turn off the water supply before proceeding.

COIL SPRING

1.

If so equipped, remove the water dump valve shield

 

from its mounting bracket.

2.

Lift and slide the coil retainer cap from the top of the

 

coil.

3.

Note the position of the coil assembly on the valve

 

for assembly later. Leaving the wires attached, lift

 

the coil assembly off the valve body and the

 

enclosing tube.

4.

Press down on the plastic nut on the enclosing tube

 

and rotate it 1/4 turn. Remove the enclosing tube,

ENCLOSING TUBE

PLUNGER

DIAPHRAM

VALVE BODY

plunger, and plastic gasket from the valve body.

NOTE: At this point, the water dump valve can easily be cleaned. If complete removal is desired, continue with step 5.

Dump Valve Disassembly

Part Number 80-1560-3

4-9

Page 30 Page 32
Image 31
Page 30 Page 32
Contents S0850M Model Ice Machines Personal Injury Potential Read These Before ProceedingSection Installation Instructions Table of Contents Section General InformationSection Maintenance Table of Contents Section Ice Machine OperationSection Before Calling For Service Ice Cube Sizes How to Read a Model NumberSection General Information Model NumbersGeneral Information Section Accessories Model/Serial Number Location Section General Information Model/Serial Number LocationWarranty Coverage General Ice Machine DimensionsWidth, Depth, and Height Dimensions Electrical and AuCS DimensionsIce Machine Heat of Rejection Installation Instructions Section Location of Ice MachineMinimum Circuit Ampacity Section Installation Instructions Electrical ServiceVoltage FUSE/CIRCUIT BreakerSelf Contained ICE Machine 230/1/50 For United Kingdom OnlySelf Contained ICE Machine 115/1/60 or 208-230/1/60 Self Contained ICE Machine 208-230/3/60Water Inlet Lines Cooling Tower Applications Water-Cooled ModelsWater Supply AIR GAPTypical Water Supply Drain Installation Installation Instructions SectionWater Supply and Drain Line SIZING/CONNECTIONS Section Installation Instructions Installation Check List Potential Personal Injury Situation Component Identification Section Ice Machine OperationInitial START-UP or START-UP After Automatic SHUT-OFF Ice Machine Operation Section Sequence Of OperationAutomatic SHUT-OFF 7. Automatic Shut-Off Safety TimersHarvest Sequence 5. Water Purge HarvestIce Thickness Check Ice Machine Operation Section Operational ChecksWater Level ICE Thickness CheckHarvest Sequence Water Purge Water Purge AdjustmentIce Machine Operation Section AlphaSan→ Exterior CleaningIce Machine Inspection Water-Cooled Condenser Water Regulating ValveClean UP Procedure for Damaged Sachet Packet Maintenance Section GuardianGuardian Sachet Replacement Frequency Sachet INSTALLATION/REPLACEMENT ProcedureCleaning Procedure Section Maintenance Interior Cleaning and SanitizingStep Sanitizing Procedure Maintenance SectionRemoval of Parts for CLEANING/SANITIZING Water Curtain Removal Ice Thickness Probe Water CurtainIce Thickness Probe Removal Water Trough Water Distribution TubeWater Distribution Tube Removal Water Pump Water Level ProbeWater Pump Removal Water Dump Valve Dump Valve DisassemblyDrain Line Check Valve Evaporator Tray RemovalWater Inlet Valve Removing the Front PanelPanel Removal Pry Open the Water Regulating Valve AUCS→ Accessory Maintenance Section Removal from Service/WinterizationSELF-CONTAINED WATER-COOLED ICE Machines Checklist Section Before Calling For ServiceSafety Limit Feature Before Calling For Service SectionPage Manitowoc ICE, INC

S0850M specifications

The Manitowoc Ice S0850M is a cutting-edge ice maker designed to meet the needs of busy commercial environments. Known for its reliability and efficiency, this machine is specifically engineered to produce high-quality ice for various applications in restaurants, bars, hotels, and other foodservice operations.

One of the standout features of the S0850M is its capacity. This model can produce up to 850 pounds of ice in a 24-hour period, making it an ideal choice for establishments that require a steady supply of ice throughout the day. The ice produced is of the cube style, which is versatile for use in beverages, food displays, and more, ensuring that it meets the demands of both front-of-house and back-of-house operations.

The Manitowoc Ice S0850M is equipped with advanced technologies that enhance its performance and energy efficiency. The unit utilizes an efficient air-cooled condenser, which allows for better heat exchange, reducing energy consumption. Additionally, its programmable slow freeze technology ensures that the ice is formed slowly, resulting in clear, high-density cubes that melt slowly, minimizing dilution of beverages.

Durability is another key characteristic of the S0850M. Constructed with stainless steel, the machine is designed to withstand the rigors of commercial use while preventing corrosion and ensuring long-lasting performance. Its compact design allows for easy installation in various locations, and it can fit well under counters or in tight spaces, providing flexibility for ice storage solutions.

For ease of use, the S0850M comes with intuitive controls that allow operators to manage production cycles efficiently. The machine also includes a built-in diagnostic system, providing real-time status updates and alerts for any maintenance needs, ensuring that the ice maker operates smoothly without unexpected downtime.

Finally, the Manitowoc Ice S0850M is designed with food safety in mind. It meets hygiene standards, preventing contamination within the ice production process. This attention to food safety and health regulations makes it a preferred choice for businesses looking for a dependable commercial ice maker.

In summary, the Manitowoc Ice S0850M ice maker combines capacity, efficiency, durability, and advanced technology to provide high-quality ice production for busy foodservice operations, ensuring that establishments can meet their ice needs effectively and reliably.
Top Page Image Contents