Grindmaster ICB-400 Temperature and Brew Timing Controls Refer to Figure C, Pushbutton Keypad

AMERICAN METAL WARE® BREWERS

TEMPERATURE AND BREW TIMING CONTROLS (Refer to Figure C)

Temperature and brew timing are set by the dial and keypad located on the main controller. This controller is positioned inside the brewer housing and is accessed by removing the screws which fasten the access panel to the brewer.

The controller stores 6 independent brew timer values. On dual brewer models, 3 timers are used for the left brewer, and 3 are used for the right brewer. On single brewer models, the timers for the left side brewer are utilized for the unit and the right brewer timers are not utilized.

	Pushbuttons to adjust timer
BREWER SELECTOR SWITCH	values and to select timers

The brewer selector switch is a 2-position slide switch located on the main controller. On dual brewer models it is used to select the left or right side timers for programming. On single brewer models, the switch should always be in the left position when programming the brew timers. To switch from side to side, slide switch to the desired position.

PUSHBUTTON KEYPAD

The pushbuttons serve 4 functions:

1)Selecting the appropriate timer

2)Adjusting the stored timing value

3)Instructing the controller to store a displayed value

4)Resetting the controller after an error has been registered

Alphanumeric LEDs to indicate	Red LEDs to indicate
timer settings and to display	which timer is being
error codes	programmed

	Brewer	selector switch
Water temperature adjustment

Figure C

The pushbutton to the right on the controller is used for 1, 3 and 4. The pushbutton to the left on the controller is used to increase the displayed value. The middle pushbutton is used to decrease the displayed value.

To select the appropriate timer once the correct brew side has been selected, press the SELECT pushbutton until the correct brew size LED is lit.

To adjust the stored timing value, press the left pushbutton to increase the displayed value or press the middle pushbutton to decrease the displayed value.

To store a displayed value, press the select button once.

To reset the controller after an error has been registered, press the right pushbutton and hold for 10 sec. After resetting, the alphanumerical LEDs will return to displaying timer values.

TEMPERATURE ADJUSTMENT KNOB

Temperature adjustment is accomplished by rotating the small knob to the left of the brewer selector switch. Clockwise rotation will increase the temperature setpoint while counterclockwise rotation will decrease the setpoint. The standard factory setting is 195o F.

OPERATION

WARNING: WATER USED FOR BREWING COFFEE IS VERY HOT. USE CAUTION WHEN BREWING, POURING OR TRANSPORTING COFFEE. NEVER ATTEMPT TO MOVE THE BREWER WITHOUT FIRST DRAINING THE WATER TANK. ACCIDENTAL SPILLS MAY RESULT IN SEVERE BURNS.

ICB brewers will perform the brew function only when a container is properly located under the brew basket; the pushbutton switch must be engaged to allow brewing. Removal of the container during a brew cycle will suspend the brewing cycle, however brew timing will continue to elapse and the brew basket will continue to drip.

•Place an empty shuttle, airpot or insulated container on the shelf, counter, or accessory base (depending on model) under the brew basket. A cold container will significantly lower the temperature of the brewed coffee. Turn on the warmer if a shuttle is used. If the shuttle is not warm, allow the warmer to heat the shuttle. A short brew of water will quickly warm the container.

•Remove the filter basket and line with a filter paper. Paper size for each basket is shown below:

Basket	Paper Size (inches)
BB1.5	13 x 5
BB2.0	14 x 6

•Place ground coffee in the brew basket. Your coffee supplier can help you select the right amount of coffee and grind. Coffee brewing experts recommend 6.5-8 oz. of coffee per gallon of water for most applications. A full shuttle contains 1.4 gal., a full airpot contains 0.8 gal. and a full insulated container contains 1.75 gal.

•Slide the brew basket into the brewer, making sure that the basket spout is properly aligned with the container opening. Rotate the basket locks into the locked or downward pointing position so that the basket can not be inadvertently removed.

•Select batch size through the touchpads. Check the WATER HOT light. If it is lit, press the START switch on the touchpad. If the WATER HOT light is not lit, wait and press START when it has become illuminated.

•Brew time is about 4 min. for full shuttles and insulated containers, less for half batches and airpots. After the brew, allow the coffee to drip for

1-2 min.

CAUTION:HOT LIQUID HAZARD!: COFFEE BASKET CONTAINS VERY HOT LIQUID UNTIL THE DRIP-THROUGH IS COMPLETED. EARLY REMOVAL OF THE BASKET COULD RESULT IN BURNS.

•Remove the brew basket, dump grounds from the basket and rinse for the next brew. Coffee is ready to serve.

•The shuttle may be moved to a remote warming station and the insulated container can be moved to a remote dispensing site.

Page 3