Graco 310554V Connecting the Control Assembly to a Power Source, Electric Shock Hazard

Page 14

Installation

Connecting the Control Assembly to a Power Source

Perform the following procedure to connect the control assembly to a power source.

ELECTRIC SHOCK HAZARD

Do not connect the PrecisionSwirl control assembly to a power source unless you are a trained electrician. Failure to follow standard procedures or to observe the necessary precautions could result in serious bodily injury or equipment damage.

CAUTION

If power and grounding connections are not done properly, the equipment may be damaged and the warranty will be voided.

Have a qualified electrician connect the PrecisionSwirl control assembly to a grounded electrical source that has the following required service ratings:

Description

Requirements

 

 

Vac

100-240

 

 

Hz

50/60

 

 

Phase

1

 

 

Full Load Amps

0.42 at 120 Vac

 

 

Circuit Breaker

5 Amp

 

 

Power to the control assembly must be supplied from a source with a lockable–off disconnect switch, or by use of a cord with a plug–and–socket connection to the source of power.

To connect the control assembly to the electrical source:

1.Shut off system power at the main circuit breaker.

2.Locate the opening on the bottom of the control assembly, labeled POWER SUPPLY. See FIG. 6.

0/7%2

!54/-!4)#)#/.42/,

-/4/2

3500,9

#!",%

#!",%

8027A

7/8 in. Diameter power supply entry

FIG. 6

3.Using 16 AWG wire or larger, connect electrical power to L1 (hot), L2 (neutral) power terminals in the PrecisionSwirl control assembly. See FIG. 8.

4.Use a cord grip to seal the area where wires enter the control assembly.

Any fitting that is used to connect a power cord (or conduit for power wiring) to the control assembly must provide a liquid–tight seal.

5.Apply system power at the main circuit breaker.

6.Move the POWER switch to the ON position, apply- ing power to the control assembly.

14

310554V

Page 13 Page 15
Image 14
Page 13 Page 15
Contents PrecisionSwirl Orbital DispenserCable Assemblies List of ModelsTool Mounted Dispensers Tool MountContents Equipment Misuse Hazard Skin Injection Hazard Fire and Explosion HazardToxic Fluid or Fumes Hazard 310554V Repair and Repacking the Product Unpacking and RepackingUnpacking the Product PrecisionSwirl Overview PrecisionSwirl CapabilitiesPrecisionSwirl in Basic Robotic System No. DescriptionMounting the Control Assembly Installing the Control AssemblyPreparing to Install the Control Assembly Electrocution HazardMounting the Control Assembly FIRE, EXPLOSION, and Electric Shock Hazard InstallationGrounding the Control Assembly Description Requirements Connecting the Control Assembly to a Power SourceElectric Shock Hazard PE/GND Connecting Material Hose to Dispense Valve Installing the Dispense ValveConnecting Air Lines to Dispense Valve Mounting the Dispense ValveInstalling Cable Assemblies Connecting the Motor Control CableMotor Control Cable 15 ft Connecting the Automatic Control Cable Signal DescriptionInspecting the Orbital Dispenser Verifying Ground ContinuityVerifying Ground Continuity Grounding the SystemPrecisionSwirl Module Operation Control Assembly Controls Button/Switch What it doesControl Assembly Indicators Button/Switch Light is Meaning Setting Operation Modes Analyzing Causes for a Motor Fault Alarm Using Automatic ModeAdjusting Orbital Dispenser Motor Speed Troubleshooting Troubleshooting Problem Cause SolutionControl Assembly Service Main Power Switch Removal Main Power Switch ReplacementPotentiometer Replacement Potentiometer RemovalPanel Assembly Service  Swirl Control Board Replacement Swirl Control Board RemovalRFI Filter Replacement RFI Filter RemovalRelay Removal Relay Replacement      Fuse Replacement Fuse RemovalControl Assembly Parts Part No. Description Qty8037B 13, 15 13, 53 42, 43 Part No , PrecisionSwirl Panel Assembly No. Part No. Description QtyControl Assembly Parts 310554V Motor Control Cable Assemblies Accessory PartsConnection Diagram SocketTorsional Motor Control Cable Assemblies Motor Control Cables Part Number Length DescriptionRobot Interface Cable Assembly Dispenser Valve Adapter FittingsWiring Diagrams Motor Controller Wiring, Lines Technical Data Control AssemblyGraco Standard Warranty Graco Information

310554V specifications

The Graco 310554V is an advanced airless paint sprayer designed for both professional contractors and DIY enthusiasts looking for a reliable and efficient solution for their painting projects. This sprayer is recognized for its versatility, ease of use, and capability to deliver a high-quality finish with minimal effort.

One of the standout features of the Graco 310554V is its powerful 3000 PSI pump. This high-pressure capability allows users to spray thicker materials and achieve excellent coverage in fewer passes. The pump is also designed with a robust construction, ensuring durability and longevity, making it suitable for heavy-duty use.

Another key characteristic of the Graco 310554V is its SmartControl technology. This innovative feature provides a consistent spray pattern at any speed, which allows users to adjust the flow of paint depending on the specific requirements of the project. Whether spraying a large surface or intricate detail work, SmartControl ensures that the finish remains smooth and even.

The Graco 310554V is equipped with a reversible spray tip that enables users to quickly unclog the nozzle without the need for disassembly. This feature is especially beneficial when working with thicker paints or when the sprayer is not frequently cleaned. The inclusion of the RAC X tip also offers a variety of spray patterns and sizes, giving users more control over the application process.

Portability is another defining feature of the Graco 310554V. It comes with a lightweight design and an integrated handle, allowing for easy transportation between job sites. Additionally, the unit includes a built-in carry handle and a durable frame that enables it to withstand the rigors of regular use.

The Graco 310554V also showcases user-friendly innovations, such as a simple on/off switch and adjustable pressure settings. These features simplify the setup process and empower users to tailor the sprayer's performance based on the material used and the type of job at hand.

Overall, the Graco 310554V combines professional-grade performance with innovative technology, making it an excellent choice for those looking to achieve a flawless finish on their painting projects. Whether you are tackling a small home improvement job or a large-scale professional painting task, this sprayer is engineered to meet varying demands and deliver outstanding results.
Top Page Image Contents