Graco 310554V important safety instructions Skin Injection Hazard, Fire and Explosion Hazard

Page 5

Warnings

WARNING

SKIN INJECTION HAZARD

Spray from the applicator, hose leaks, or ruptured components can inject fluid into your body and cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury.

•Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate surgical treatment.

•Do not point the applicator at anyone or at any part of the body.

•Do not put hand or fingers over the front of the applicator.

•Do not stop or deflect fluid leaks with your hand, body, glove, or rag.

•Follow the Pressure Relief Procedure from manual 309403 whenever you are instructed to: relieve pressure; stop dispensing; clean, check, or service the equipment; or install or clean a nozzle.

•Tighten all the fluid connections before operating the equipment.

•Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately. Permanently coupled hoses cannot be repaired; replace the entire hose.

•Always wear eye protection and protective clothing when installing, operating, or servicing this dis- pensing equipment.

•Do not remove or modify any part of the applicator; this can cause a malfunction and result in seri- ous bodily injury.

•Use extreme caution when cleaning or changing nozzles. If the nozzle clogs while applying material, Always follow the Pressure Relief Procedure from manual 309403, then remove the nozzle to clean it.

•Never wipe off build–up around the nozzle or inlet cap until pressure is fully relieved.

FIRE AND EXPLOSION HAZARD

Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition and result in fire or explosion and serious injury.

•Ground the equipment and the object being dispensed. See Grounding on page 20.

•Ground the equipment and the object being sprayed, and all other electrically conductive objects in the dispense area. Proper grounding dissipates static electricity generated in the equipment. See Grounding on page 20.

•Do not use this equipment with flammable liquids.

•Keep the dispense area free of debris, including solvent, rags, and gasoline.

•If there is any static sparking or you feel an electric shock while using the equipment, stop dispens- ing immediately. Do not use the equipment until you have identified and corrected the problem.

•Be sure all electrical work is performed by a qualified electrician only.

•Have any checks, installation, or service to electrical equipment performed by a qualified electrician only.

•Be sure all electrical equipment is installed and operated in compliance with applicable codes.

•Be sure power is disconnected when servicing and repairing equipment.

•Before operating the equipment, extinguish all open flames or pilot lights in the dispense area.

•Do not smoke in the dispensing area.

•Keep liquids away from the electrical components

•Disconnect electrical power at the main switch before servicing the equipment.

310554V

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Orbital Dispenser PrecisionSwirlTool Mounted Dispensers List of ModelsCable Assemblies Tool MountContents Equipment Misuse Hazard Fire and Explosion Hazard Skin Injection HazardToxic Fluid or Fumes Hazard 310554V Repair and Repacking the Product Unpacking and RepackingUnpacking the Product PrecisionSwirl Capabilities PrecisionSwirl OverviewNo. Description PrecisionSwirl in Basic Robotic SystemPreparing to Install the Control Assembly Installing the Control AssemblyMounting the Control Assembly Electrocution HazardMounting the Control Assembly FIRE, EXPLOSION, and Electric Shock Hazard InstallationGrounding the Control Assembly Description Requirements Connecting the Control Assembly to a Power SourceElectric Shock Hazard PE/GND Connecting Air Lines to Dispense Valve Installing the Dispense ValveConnecting Material Hose to Dispense Valve Mounting the Dispense ValveConnecting the Motor Control Cable Installing Cable AssembliesMotor Control Cable 15 ft Signal Description Connecting the Automatic Control CableVerifying Ground Continuity Verifying Ground ContinuityInspecting the Orbital Dispenser Grounding the SystemPrecisionSwirl Module Operation Control Assembly Controls Button/Switch What it doesControl Assembly Indicators Button/Switch Light is Meaning Setting Operation Modes Using Automatic Mode Analyzing Causes for a Motor Fault AlarmAdjusting Orbital Dispenser Motor Speed Troubleshooting Problem Cause Solution TroubleshootingControl Assembly Service Main Power Switch Replacement Main Power Switch RemovalPotentiometer Removal Potentiometer Replacement  Panel Assembly ServiceSwirl Control Board Removal Swirl Control Board ReplacementRFI Filter Removal RFI Filter Replacement      Relay Removal Relay ReplacementFuse Removal Fuse ReplacementPart No. Description Qty Control Assembly Parts8037B 13, 15 13, 53 42, 43 No. Part No. Description Qty Part No , PrecisionSwirl Panel AssemblyControl Assembly Parts 310554V Connection Diagram Accessory PartsMotor Control Cable Assemblies SocketMotor Control Cables Part Number Length Description Torsional Motor Control Cable AssembliesDispenser Valve Adapter Fittings Robot Interface Cable AssemblyMotor Controller Wiring, Lines Wiring Diagrams Control Assembly Technical DataGraco Information Graco Standard Warranty

310554V specifications

The Graco 310554V is an advanced airless paint sprayer designed for both professional contractors and DIY enthusiasts looking for a reliable and efficient solution for their painting projects. This sprayer is recognized for its versatility, ease of use, and capability to deliver a high-quality finish with minimal effort.

One of the standout features of the Graco 310554V is its powerful 3000 PSI pump. This high-pressure capability allows users to spray thicker materials and achieve excellent coverage in fewer passes. The pump is also designed with a robust construction, ensuring durability and longevity, making it suitable for heavy-duty use.

Another key characteristic of the Graco 310554V is its SmartControl technology. This innovative feature provides a consistent spray pattern at any speed, which allows users to adjust the flow of paint depending on the specific requirements of the project. Whether spraying a large surface or intricate detail work, SmartControl ensures that the finish remains smooth and even.

The Graco 310554V is equipped with a reversible spray tip that enables users to quickly unclog the nozzle without the need for disassembly. This feature is especially beneficial when working with thicker paints or when the sprayer is not frequently cleaned. The inclusion of the RAC X tip also offers a variety of spray patterns and sizes, giving users more control over the application process.

Portability is another defining feature of the Graco 310554V. It comes with a lightweight design and an integrated handle, allowing for easy transportation between job sites. Additionally, the unit includes a built-in carry handle and a durable frame that enables it to withstand the rigors of regular use.

The Graco 310554V also showcases user-friendly innovations, such as a simple on/off switch and adjustable pressure settings. These features simplify the setup process and empower users to tailor the sprayer's performance based on the material used and the type of job at hand.

Overall, the Graco 310554V combines professional-grade performance with innovative technology, making it an excellent choice for those looking to achieve a flawless finish on their painting projects. Whether you are tackling a small home improvement job or a large-scale professional painting task, this sprayer is engineered to meet varying demands and deliver outstanding results.
Top Page Image Contents