Graco 310554V important safety instructions Equipment Misuse Hazard

Page 4

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNING

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result in serious injury.

•This equipment is for professional use only.

•Read all instruction manuals, warnings, tags, and labels before operating the equipment.

•Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco distributor.

•Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

•Check the equipment daily. Repair or replace worn or damaged parts immediately.

•Do not exceed the maximum fluid working pressure of 3500 psi (241 bar, 24.1 MPa) to the dispenser or manifold.

•Never exceed the recommended working pressure or the maximum air inlet pressure stated on your pump or in the Technical Data section on page 63.

•Be sure that all spray/dispensing equipment and accessories are rated to withstand the maximum working pressure of the pump. Do not exceed the maximum working pressure of any component or accessory used in the system.

•Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

•Do not expose Graco standard hoses to temperatures above 180° F (82° C) or below -40° F (-40° C).

•Do not use the hoses to pull the equipment.

•Use only fluids and solvents that are compatible with the equipment wetted parts. See the Technical Data sections of all the equipment manuals. Read the fluid manufacturer’s warnings.

•Always wear protective eyewear, gloves, clothing, and respirator as recommended by the fluid and solvent manufacturers.

•Comply with all applicable local, state, and national fire, electrical, and other safety regulations.

4

310554V

Page 3 Page 5
Image 4
Page 3 Page 5
Contents PrecisionSwirl Orbital DispenserList of Models Tool Mounted DispensersCable Assemblies Tool MountContents Equipment Misuse Hazard Skin Injection Hazard Fire and Explosion HazardToxic Fluid or Fumes Hazard 310554V Unpacking the Product Unpacking and RepackingRepair and Repacking the Product PrecisionSwirl Overview PrecisionSwirl CapabilitiesPrecisionSwirl in Basic Robotic System No. DescriptionInstalling the Control Assembly Preparing to Install the Control AssemblyMounting the Control Assembly Electrocution HazardMounting the Control Assembly Grounding the Control Assembly InstallationFIRE, EXPLOSION, and Electric Shock Hazard Electric Shock Hazard Connecting the Control Assembly to a Power SourceDescription Requirements PE/GND Installing the Dispense Valve Connecting Air Lines to Dispense ValveConnecting Material Hose to Dispense Valve Mounting the Dispense ValveInstalling Cable Assemblies Connecting the Motor Control CableMotor Control Cable 15 ft Connecting the Automatic Control Cable Signal DescriptionVerifying Ground Continuity Verifying Ground ContinuityInspecting the Orbital Dispenser Grounding the SystemControl Assembly Indicators Button/Switch Light is Meaning Control Assembly Controls Button/Switch What it doesPrecisionSwirl Module Operation Setting Operation Modes Analyzing Causes for a Motor Fault Alarm Using Automatic ModeAdjusting Orbital Dispenser Motor Speed Troubleshooting Troubleshooting Problem Cause SolutionControl Assembly Service Main Power Switch Removal Main Power Switch ReplacementPotentiometer Replacement Potentiometer RemovalPanel Assembly Service  Swirl Control Board Replacement Swirl Control Board RemovalRFI Filter Replacement RFI Filter RemovalRelay Removal Relay Replacement      Fuse Replacement Fuse RemovalControl Assembly Parts Part No. Description Qty8037B 13, 15 13, 53 42, 43 Part No , PrecisionSwirl Panel Assembly No. Part No. Description QtyControl Assembly Parts 310554V Accessory Parts Connection DiagramMotor Control Cable Assemblies SocketTorsional Motor Control Cable Assemblies Motor Control Cables Part Number Length DescriptionRobot Interface Cable Assembly Dispenser Valve Adapter FittingsWiring Diagrams Motor Controller Wiring, Lines Technical Data Control AssemblyGraco Standard Warranty Graco Information

310554V specifications

The Graco 310554V is an advanced airless paint sprayer designed for both professional contractors and DIY enthusiasts looking for a reliable and efficient solution for their painting projects. This sprayer is recognized for its versatility, ease of use, and capability to deliver a high-quality finish with minimal effort.

One of the standout features of the Graco 310554V is its powerful 3000 PSI pump. This high-pressure capability allows users to spray thicker materials and achieve excellent coverage in fewer passes. The pump is also designed with a robust construction, ensuring durability and longevity, making it suitable for heavy-duty use.

Another key characteristic of the Graco 310554V is its SmartControl technology. This innovative feature provides a consistent spray pattern at any speed, which allows users to adjust the flow of paint depending on the specific requirements of the project. Whether spraying a large surface or intricate detail work, SmartControl ensures that the finish remains smooth and even.

The Graco 310554V is equipped with a reversible spray tip that enables users to quickly unclog the nozzle without the need for disassembly. This feature is especially beneficial when working with thicker paints or when the sprayer is not frequently cleaned. The inclusion of the RAC X tip also offers a variety of spray patterns and sizes, giving users more control over the application process.

Portability is another defining feature of the Graco 310554V. It comes with a lightweight design and an integrated handle, allowing for easy transportation between job sites. Additionally, the unit includes a built-in carry handle and a durable frame that enables it to withstand the rigors of regular use.

The Graco 310554V also showcases user-friendly innovations, such as a simple on/off switch and adjustable pressure settings. These features simplify the setup process and empower users to tailor the sprayer's performance based on the material used and the type of job at hand.

Overall, the Graco 310554V combines professional-grade performance with innovative technology, making it an excellent choice for those looking to achieve a flawless finish on their painting projects. Whether you are tackling a small home improvement job or a large-scale professional painting task, this sprayer is engineered to meet varying demands and deliver outstanding results.
Top Page Image Contents