Jackson Avenger HT, Avenger LT INSTALLATION/OPERATION Instructions, Installation Instructions

Page 13

SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

VISUAL INSPECTION: Before installing the unit, check the container and machine for damage. A damaged container is an indi- cator that there may be some damage to the machine. If there is damage to both the container and machine, do not throw away the container. The dishmachine has been inspected and packed at the factory and is expected to arrive to you in new, undam- aged condition. However, rough handling by carriers or others may result in there being damage to the unit while in transit. If such a situation occurs, do not return the unit to Jackson; instead, contact the carrier and ask them to send a representative to the site to inspect the damage to the unit and to complete an inspection report. You must contact the carrier within 48 hours of receiving the machine. Also, contact the dealer through which you purchased the unit.

UNPACKING THE DISHMACHINE: Once the machine has been removed from the container, ensure that there are no miss- ing parts from the machine. This may not be obvious at first. If it is discovered that an item is missing, contact Jackson imme- diately to have the missing item shipped to you.

LEVEL THE DISHMACHINE: The dishmachine is designed to operate while being level. This is important to prevent any damage to the machine during operation and to ensure the best results when washing ware. The unit comes with adjustable bullet feet, which can be turned using a pair of channel locks or by hand if the unit can be raised safely. Ensure that the unit is level from side to side and from front to back before making any connections.

 

 

Adjustable Bullet Foot

PLUMBING THE DISHMACHINE: All plumbing connections must comply with all applicableB

Drain Hose

BACK

local, state, and national plumbing codes. The plumber is responsible for ensuring that the

 

incoming water line is thoroughly flushed prior to connecting it to any component of the dish-

 

 

machine. It is necessary to remove all foreign debris from the water line that may potential-

 

 

ly get trapped in the valves or cause an obstruction. Any valves that are fouled as a result

 

 

of foreign matter left in the water line, and any expenses resulting from this fouling, are not

 

 

the responsibility of the manufacturer. A water hardness test must be performed to deter-

 

 

mine if the HTS-11 (scale prevention and corrosion control) need to be installed. A hardness

 

 

test kit is attached to the warning tag that is attached to the incoming plumbing connection

 

 

on the back of the machine. If the hardness is higher than 5 GPG the HTS-11 will need to

 

 

be installed, please contact Jackson immediately to have this item shipped to you.

 

 

WATER SUPPLY CONNECTION FOR MACHINES WITH A WATER HARDNESS

 

 

GREATER THAN 5 GPG: Ensure that you have read the section entitled “PLUMBING THE

 

 

DISHMACHINE” above before proceeding. Install the HTS-11 into the water line (1/2” ID

 

 

pipe size minimum) before the dishmachine line incoming water connection point using cop-

 

 

per pipe. The HTS-11 must be installed vertically. A mounting bracket is provided to facili-

 

 

tate the venture metering head to the wall. Observe proper inlet/outlet water directions. Flow

 

 

directions are molded into the top of the head. It is recommended that a water shut-off valve

15

 

 

Back of Machine Showing Drain Hose

be installed before the HTS-11 to allow access for servicing. Plumb from the HTS-11 outlet

116

[50mm]

 

 

to the incoming water connection point using copper pipe (or order the 1/2” ID flexible hose

 

 

kit offered by Jackson). The water supply line is to be capable of 20±5 PSI “flow” pressure

 

 

at the recommended temperature indicated on the data plate. See “Shock Absorber” section.

 

 

WATER SUPPLY CONNECTION FOR MACHINES WITH A WATER HARDNESS OF 5 GPG

 

 

OR LESS:Ensure that you have read the section entitled “PLUMBING THE DISHMACHINE”

 

 

above before proceeding. Install the water supply line (1/2” ID pipe size minimum) to the

 

 

dishmachine incoming water connection point using copper pipe (or order the 1/2” ID flexi-

 

 

ble hose kit offered by Jackson). It is recommended that a water shut-off valve be installed

 

 

in the water line between the main supply and the machine to allow access for service. The

 

 

water supply line is to be capable of 20±5 PSI “flow” pressure at the recommended tem-

Back of unit showing

 

perature indicated on the data plate.

Incoming Plumbing Water Connection

PRESSURE REGULATOR: Jackson has provided a water pressure regulator due to areas where the water pressure fluctu- ates or is lower than the recommended pressure. In some cases, you many not need the regulator and in those cases, the reg- ulator may be removed. Do not confuse static pressure with flow pressure. Static pressure is the line pressure in a “no flow” condition (all valves and services are closed). Flow pressure is the pressure in the fill line when the fill valve is opened during the cycle.

Avenger™ Series Technical Manual 7610-003-34-01 Rev. A

Issued: 05-02-2007 Revised: N/A

7

Image 13
Contents For Jackson Models INSTALLATION/OPERATION Technical ManualONE Year Limited Parts & Labor Warranty Manufacturers WarrantyStop Pare Arret Revision Date Made Applicable By ECN Details Nomenclature for the Models Covered in this Manual Model Serial No Installation Date Service Rep. Name Phone NoTable of Contents Section Specification Information Specification Information Temperatures Electrical Requirements Specifications of the AvengerltOperating Cycle Seconds Wash Time AvengerLTAvengerHT Dimensions AvengerLT Dimensions Section INSTALLATION/OPERATION Instructions Installation Instructions INSTALLATION/OPERATION InstructionsWater Supply Connection for Machines with a Water Hardness Electrical Installation Instructions To Prepare Chemical Feeder Pumps for Operation Chemical Dispensing EquipmentPriming Chemical Feeder Pumps Avenger HT Avenger LT Detergent Control Operation Instructions Operation Instructions /DELIMING Instructions Section Preventative Maintenance Preventative Maintenance Section Troubleshooting Common Problems Troubleshooting SectionProblem Water overflow from bottom of door Problem Wash motor doesn’t operate on manual washProblem No indication of pressure Problem Rinse water not at required temperature rangeSection Parts Section Control Panel Weldment Assemblies Parts SectionComplete Control Panel Assembly Control Panel ASSEMBLY/KICK Panel Weldment AvengerhtQTY Description Mfg. NoControl Panel ASSEMBLY/KICK Panel Weldment Avengerlt Terminal Block BOX Assembly Complete Chemical Feeder Pump Assembly 05700-003-32-03 Chemical Feeder Pump Assembly AvengerhtChemical Feeder Pump Assembly Avengerht QTY Description Complete Chemical Feeder Pump Assembly 05700-003-33-32 Chemical Feeder Pump Assembly AvengerltChemical Feeder Pump Assembly Avengerlt QTY Description Chemical Feeder Pump Components Complete Incoming Plumbing Assembly 05700-003-36-32 Vacuum Plumbing Assembly 05700-003-32-14Plumbing Assemblies Avengerht Plumbing Assemblies Avengerlt Plumbing AssemblyComplete Incoming Complete 110 Volt Solenoid Valve Assembly, 1/2 Complete Vacuum Breaker Assembly, 1/2 NPTCoil & Housing only, 1/2 05700-002-64-67 Complete 220 Volt Solenoid Valve Assembly, 1/2Area within this box is an overall Wash MOTOR/DRAIN PLUMBING/ Avengerlt Wash Manifold AssemblyHub, Discharge Machined AvengerHT Shown Other parts not shown Motor & Pump AssemblyRinse ARM & Wash ARM Assemblies Wash Arm Assembly 2 per AvengerLT 1 per AvengerHTComplete Rinse Tank Assembly Avengerht Only 05700-003-31-94 Thermostat & Rinse Tank AssemblyComplete Door Assembly 05700-003-32-09 Door AssemblyDoor Assembly QTY Description Miscellaneous Door Components Frame & Panel Components Miscellaneous Parts Stands & Components Stand AssemblyHTS-11 Scale Prevention & Corrosion Control Device GO BOX KIT Section Electrical Schematics AvengerHT 208-230 Volt 60 Hertz Single Phase Electrical SchematicsAvengerLT 115 Volt 60 Hertz Single Phase Section Jackson Maintenance Repair Centers Alabama to Florida Jackson Maintenance & Repair CentersFlorida to Maryland Service COMaryland to NEW York Jackson Service CompaNEW York to Pennsylvania Certified Service Center Rons ServiceCENTER, INC Rhode Island to WisconsinWisconsin to WYOMING/INTERNATIONAL
Related manuals
Manual 2 pages 9.06 Kb Manual 2 pages 17.61 Kb

Avenger HT, Avenger LT specifications

The Jackson Avenger HT and Avenger LT are two outstanding models in the Jackson line of guitars renowned for their exceptional playability, tonal versatility, and innovative features. Both models cater to a wide range of playing styles, from rock and metal to blues and jazz, making them suitable instruments for musicians at any level.

The Avenger HT is designed for those who seek the aggressive tonal characteristics and performance features typically associated with hard rock and metal genres. One of its standout features is the high-output humbucker pickups that deliver a powerful, punchy sound while maintaining clarity and responsiveness. Coupling these pickups with an ergonomic body shape ensures comfort during extended playing sessions, allowing artists to perform confidently.

In contrast, the Avenger LT emphasizes a lighter design while maintaining a robust tone and superior playability. This model incorporates a unique combination of tonewoods, which optimizes resonance and sustain. The lightweight body eases the burden of long performances, making it a favorite among players who prioritize comfort without sacrificing sound quality.

Both the HT and LT models feature advanced technologies such as locking tuners, which provide tuning stability and facilitate quick string changes. This feature is especially appreciated by performing musicians who need to maintain pitch accuracy throughout a set. Additionally, each model boasts a modern neck profile designed for speed and ease of play, perfect for intricate solos and swift chord changes.

Another remarkable aspect of the Avenger series is the use of high-quality finishes that not only enhance the aesthetic appeal but also provide added durability. Each guitar is crafted with meticulous attention to detail, resulting in a striking, professional-grade instrument that stands the test of time.

For those seeking versatility, the Avenger HT and LT come equipped with various control options, including coil-splitting capabilities. This allows players to switch between humbucker and single-coil sounds, opening up a world of tonal possibilities with a simple flick of a switch.

In summary, the Jackson Avenger HT and LT guitars stand out for their exceptional craftsmanship, innovative features, and versatile playability. Whether you prefer the heavier sound and feel of the HT or the lightweight comfort of the LT, both models offer musicians the tools they need to excel in their musical endeavors. With their striking designs, advanced technology, and affordability, these guitars are a worthy addition to any player's collection.