Russound manual ST2-XM Tuner Programming, ST2 Tuner Setup Menu, ST2 Chassis Setup Menu

Page 26

ST2-XM TUNER PROGRAMMING

ST2 TUNER SETUP MENU

ST2-XM Tuner Setup Menus

Note: The Setup Menu procedures must be performed from the ST2-XM Tuner front panel.

The ST2-XM Tuner Setup Menus provide setup and naming procedures for the ST2-XM main chassis, the XM tuner module and the AM/FM tuner module. These procedures include source number assign- ments, assigning a custom name to a memory preset or a bank, choosing a region for AM/FM opera- tion (US or Euro), factory initialization and system information.

If the ST2-XM is used with a non-RNETsystem, the ST2-XM can be connected and operated without any setup programming. Follow the setup menus if custom names are desired, or for system info.

If the ST2-XM is used with an RNET system such as CAV6.6, the following minimum setup must be performed for the ST2-XM to be properly controlled by the CAV6.6.

1.ST2 Chassis Setup Menu - Assign source numbers to Tuner 1 and Tuner 2.

2.CAV6.6 Source Setup Menu - Assign the corresponding source numbers to Tuner 1 and Tuner 2.

3.CAV6.6 Source Setup Menu - Assign command type PERIPHERAL to Tuner 1 and Tuner 2.

NOTE: Once the programming procedures are completed, cycle power first to the Tuner and then to the CAV6.6 (must be powered on last) to establish a connection.

ST2 Chassis Setup Menu

Source Number (Chassis)

The Source Number procedure permits Tuner 1 (XM) and Tuner 2 (AM/FM) to be assigned the proper peripheral source identities as will be assigned in the CAV6.6 Source Setup.

1.Enter the Setup Menu by pressing and holding the TNR SEL button.

2.TUNER SETUP appears. Press MEM Up/Down until SOURCE NUM appears on the tuner.

3.Press BAND. TUNER # appears.

4.Press the Tune Up/Down buttons to select the Tuner # (Tuner 1 is XM, Tuner 2 is AM/FM).

5.Press BAND. SOURCE NUM appears.

6.Press the Tune Up/Down buttons to scroll through the source numbers 1-6.

7.Press BAND to select the source number (as assigned in the CAV6.6 setup process).

8.Repeat the process for the next tuner.

9.Press TNR SEL to exit the Source Number menu.

Update Firmware (Chassis)

The Update Firmware procedure allows the ST2 tuner’s OS firmware to be updated. The proce- dure is performed using a DB9 serial cable with one end connected to the RS-232 port on the back of the tuner and the other connected to a PC or laptop. If an OS firmware update is avail- able, it can be obtained through the Document Center at www.russound.com. XM tuner module firmware must be performed by an authorized Russound service facility.

1.Enter the Setup Menu by pressing and holding the TNR SEL button.

2.TUNER SETUP appears. Press MEM Up/Down until UPDATE FIRMW appears on the tuner.

3.Press BAND to enter the UPDATE FIRMW menu.

26

Image 26
Contents Page Important Safeguards Safety InstructionsTable of Contents RNET-enabled System IntroductionBOX Contents Component Guide ST2-XM Front PanelST2-XM Rear Panel ST2 Smart TunerST2-RC Remote Control Seek UP/DOWNST2-XM Setup and Connections Basic ConnectionsST2-KP and CAV6.6 Connections ST2-KP Connections to ST2-XM Tuner Non-RNET SystemsSource Connections with CAi Series Controller/Amplifier Source Connections with A-BUS Audio Distribution HubAntenna Connections XM Signal Strength ModeConnecting an Indoor and Outdoor Antenna XM AntennaGrounding an Outdoor Antenna AM AntennaFM Antenna XM Radio Activation ST2-XM OperationXM Radio Overview XM Radio DisplaysFor all XM Modes XM Radio ModesXM Radio Modes Preset default Mode Category Search Mode 1.CAT Search Now Playing Mode 2.NOW Playng Display Preference Mode 3.DSPLY PrefFront Panel Controls Front Panel OperationFrequency Seek AM/FM only ST2-RC Remote Control OperationTurning the unit on/off Saving FavoritesST2-KP Keypad Controls ST2-KP Keypad OperationFrequency Scan AM/FM only UNO-S2 Keypad Controls with CAV6.6CAV6.6-UNO-S2 Keypad Operation MuteSelect UNO-LRC1 Remote Control with CAV6.6 UNO-LRC1 Remote Control OperationSelect Update Firmware Chassis ST2 Tuner Setup MenuST2 Chassis Setup Menu ST2-XM Tuner ProgrammingST2 Chassis Setup Procedures Factory Initialization ChassisXM Setup Menu Memory Name Procedure System Info ChassisMemory Name XM Tuner Setup Menu for XMXM Setup Menu Bank Name Procedure Controller ID XM Diagnostics XMBank Name XM Factory Initialization XMMemory Name AM/FM Tuner Setup Menu for AM/FMSystem Info XM Bank Name AM/FM Region AM/FMBackup and Restore AM/FM Setup MenuSource Configuration Note Programming for CAV6.6 USETechnical Specification ST2-XM Smart TunerWarranty & Repair Page Page Page Russound 28-1160 07/13/04