Russound ST2-XM manual Backup and Restore, AM/FM Setup Menu

Page 33

ST2-XM TUNER PROGRAMMING

ST2 TUNER SETUP MENU

Backup and Restore

Once all of the tuner settings are completed, it may be advisable to create a backup of the pro- grammed settings for future use. The backup will then be available in case tuner settings need to be restored.

The backup and restore PC application “RNET Backup” is available through the Document Center at www.russound.com. Also required are a DB9 male-to-female cable and laptop or desk- top PC.

Press TNR SEL

button to select

AM/FM Tuner

TNR TNR

SEL SEL

AM/FM Setup Menu

TUNER

SOURCE

UPDATE

FACTORY

SYSTEM

Chassis

SETUP

NUM

FIRMW

INIT

INFO

Setup

Menu

Procedure

Procedure

Procedure

Procedure

Menu

TNR

 

 

 

 

 

 

SEL

 

 

 

 

 

 

MEM

 

 

BANK

 

REGION

AM/FM

NAME

 

 

NAME

 

Procedure

Setup

Procedure

 

 

Procedure

 

 

Menu

 

 

 

 

 

 

TNR

 

 

 

 

 

 

SEL

 

 

 

 

 

 

 

 

 

TNR

 

 

 

 

 

 

SEL

 

 

 

BANK #

MEMORY #

MEMORY

 

 

 

 

NAME

 

 

 

 

 

 

 

 

 

 

 

 

 

BANK #

BANK

SAVE

 

 

 

 

NAME

CHANGES?

 

 

 

 

 

 

 

 

Selects

 

 

 

 

 

 

character

 

 

 

 

 

 

 

 

Selects

 

 

 

 

Selects

 

character

 

 

 

 

 

 

 

 

 

 

character

 

 

 

 

 

 

position

 

 

 

 

 

 

Repeat

 

Selects

 

 

 

 

for each

 

character

 

 

 

 

character

 

position

 

 

 

 

in name

 

 

 

 

 

 

 

 

Repeat

 

 

 

 

 

 

for each

 

 

 

 

 

 

character

 

 

 

 

SAVE

 

in name

 

 

 

 

 

 

 

 

 

 

CHANGES?

 

 

 

 

33

Image 33
Contents Page Safety Instructions Important SafeguardsTable of Contents Introduction RNET-enabled SystemBOX Contents ST2-XM Front Panel Component GuideST2 Smart Tuner ST2-XM Rear PanelSeek UP/DOWN ST2-RC Remote ControlBasic Connections ST2-XM Setup and ConnectionsST2-KP Connections to ST2-XM Tuner Non-RNET Systems ST2-KP and CAV6.6 ConnectionsSource Connections with A-BUS Audio Distribution Hub Source Connections with CAi Series Controller/AmplifierConnecting an Indoor and Outdoor Antenna XM Signal Strength ModeAntenna Connections XM AntennaAM Antenna FM AntennaGrounding an Outdoor Antenna XM Radio Overview ST2-XM OperationXM Radio Activation XM Radio DisplaysXM Radio Modes XM Radio ModesFor all XM Modes Preset default Mode Category Search Mode 1.CAT Search Display Preference Mode 3.DSPLY Pref Now Playing Mode 2.NOW PlayngFront Panel Operation Front Panel ControlsTurning the unit on/off ST2-RC Remote Control OperationFrequency Seek AM/FM only Saving FavoritesST2-KP Keypad Operation ST2-KP Keypad ControlsCAV6.6-UNO-S2 Keypad Operation UNO-S2 Keypad Controls with CAV6.6Frequency Scan AM/FM only MuteSelect UNO-LRC1 Remote Control Operation UNO-LRC1 Remote Control with CAV6.6Select ST2 Chassis Setup Menu ST2 Tuner Setup MenuUpdate Firmware Chassis ST2-XM Tuner ProgrammingFactory Initialization Chassis ST2 Chassis Setup ProceduresSystem Info Chassis XM Setup Menu Memory Name ProcedureTuner Setup Menu for XM XM Setup Menu Bank Name ProcedureMemory Name XM Bank Name XM Diagnostics XMController ID XM Factory Initialization XMTuner Setup Menu for AM/FM System Info XMMemory Name AM/FM Region AM/FM Bank Name AM/FMAM/FM Setup Menu Backup and RestoreProgramming for CAV6.6 USE Source Configuration NoteST2-XM Smart Tuner Technical SpecificationWarranty & Repair Page Page Page Russound 28-1160 07/13/04