Sterling 882.93092.01 manual Maintaining the Evaporator, Evaporator Process Piping Y-Strainer

Page 49

Caution! Do not use steam or water over 140ºF (60ºC) to clean a condenser unless you are monitoring the refrigeration circuit for excessive pressure with gauges. Only a trained technician should use this method.

5-4 Maintaining the Evaporator

Dirty evaporator heat exchange surfaces reduce system capacity and efficiency. Remove dirt and slime in the evaporator by reverse-circulating with a mild detergent and water solution.

Remove mineral deposits by reverse-circulating Non-Acid De-Scaling Solution (Part No. A0553840). Follow the directions on the container.

5-5 Evaporator Process Piping Y-Strainer

The process piping Y-strainer requires periodic cleaning of its screen to insure the proper flow through the evaporator. To clean the strainer screen, remove the access plug and retaining cap, and pull out the screen.

Wipe, brush, or vacuum out any dirt left in the strainer body. Clean the screen and replace it in the strainer taking care to fit it squarely into the machined seat provided.

Caution! Do not forget to re-install the screen after cleaning it. Operating the chiller with no strainer screen can potentially plug the evaporator with dirt. The warranty does not cover chiller failures from a dirty evaporator.

5-6 Preventative Maintenance Service

Follow a systematic preventive maintenance program to help avoid costly down time. Call the Service Department to arrange a schedule of inspections. This service can be tailored to fit your maintenance requirements. These inspections include, but are not limited to:

Checking refrigerant suction and discharge pressures

Checking safety and operating conditions

Checking voltage and amperage of all motors

Checking all electrical connections

Checking quantity of refrigerant

Checking compressor oil level on units with tandem compressors

Checking lubrication of motor and pump bearings

Checking circulating pump operation

Checking flow through heat exchangers

Checking compressor efficiency

Checking noise levels

GP Series Portable Chillers

Chapter 5: Maintenance

49 of 90

Image 49
Contents GP Series Portable Chillers Shipping Information Table of Contents Chapter Troubleshooting How to Use This Manual SafetySafety Symbols Used in this Manual Responsibility  Wear Safety Glasses and Work GlovesModels Covered in This Manual Functional DescriptionGeneral Description Typical ApplicationsChilled Water Circuit System Control Refrigeration CircuitMechanical Features Standard FeaturesRefrigeration Features Electrical FeaturesController Features Safety Devices and InterlocksOther Features Crankcase HeaterHigh Pressure Cutout Flow Switch Optional FeaturesRemote Start/Stop Interlock Mounting Features Uncrating InstallationElectrical Connections Bypass Valve Considerations Process Water ConnectionsWater Treatment Considerations Galvanic Corrosion ConsiderationsCondenser Considerations Water-Cooled Chiller CondensersAir-Cooled Chiller Condensers Typical GP20-50 Water Cooled Condenser ConnectionsRemote Air-Cooled Chiller Condensers Towards the condenser GPRC-40 GPRC-105 Discharge Line Sizing Refrigerant Charge Determination Remote Condenser Configurations Checking Motor Direction Three-Phase CompressorsWater Pumps Condenser FanPart Number Description Water ReservoirSuggested Overhead Piping Configuration Pump Initial Start-Up Automatic Water Make-Up OptionPage Finishing Setup Setting Up Passwords Supervisor Password to complete the security setup Operation Panel Buttons, Indicator Lights, and SwitchesMicroprocessor Controller Main Status Screen Operator Setpoints Screen Status ScreensMain Chiller Status Screen GP Series Portable Chillers Operation Page Controller Setpoints Access LevelsGP Series Portable Chillers Operation Menu Screen Operator Setpoints Screen These configurations are described below Configuration SettingsWEB Optional Communications AlarmsFilter Cleaning MaintenanceLubrication Maintaining the CondenserMaintaining the Evaporator Preventative Maintenance ServiceEvaporator Process Piping Y-Strainer Identifying the Cause of a Problem TroubleshootingGP Series Portable Chillers Troubleshooting SC/W System fault GP Series Portable Chillers Troubleshooting Problem Possible cause Solution Non-Controller Related IssuesGP Series Portable Chillers Troubleshooting GP Series Portable Chillers Troubleshooting Returned Material Policy AppendixTechnical Assistance Sales Department Service DepartmentContract Department Air-Cooled Portable Chillers SpecificationsGPAC-40 GPAC-70 GPAC-105 GPAC-175 GPWC-20 Water-Cooled Portable ChillersGPWC-40 GPWC-70 GPWC-105 GPWC-175 Hertz Pump Curves Pump Curves, Flow, and Pressure ConsiderationsALL 60 Hz ALL 50 Hz ALL 50 Hz Calculating Chiller Nominal Flow and Pressure to Process Remote Air-Cooled Chiller Configurations Double Riser Detail Typical Ductwork for Air-Cooled Chillers Water column = Pascal GP Series Portable Chillers Appendix Piping Diagrams GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix

882.93092.01 specifications

The Sterling 882.93092.01 is an impressive timepiece that exemplifies the perfect blend of artistry and precision engineering. This elegant watch is a testament to the craftsmanship that defines the Sterling brand, making it a sought-after choice for both watch aficionados and casual wearers alike.

One of the main features of the Sterling 882.93092.01 is its exceptional movement technology. This watch is powered by a reliable automatic movement, ensuring accurate timekeeping without the need for battery replacements. The self-winding mechanism harnesses the natural motion of the wearer's wrist, providing a seamless and hassle-free experience.

The design of the Sterling 882.93092.01 is another standout characteristic. The watch features a stainless steel case that provides durability and a sleek aesthetic. The polished finish adds a touch of sophistication, making it suitable for both formal and casual settings. With a diameter that fits comfortably on the wrist, it is designed for effortless wear throughout the day.

Additionally, the face of the Sterling 882.93092.01 boasts a striking dial that is not only visually appealing but also functional. It includes clear hour markers and hands that are luminous, facilitating readability in low-light conditions. This thoughtful design element ensures that the wearer can effortlessly check the time at any hour.

Another notable aspect is the watch's water resistance. The Sterling 882.93092.01 is rated for water resistance, making it suitable for everyday wear, including light swimming and exposure to splashes. This feature enhances the watch’s practicality, allowing it to withstand the rigors of daily life without compromising its integrity.

Finally, the bracelet of the Sterling 882.93092.01 is crafted with comfort and style in mind. It features an adjustable clasp that allows for a customized fit, ensuring that the watch remains secure on the wrist. The combination of high-quality materials and impeccable design makes the bracelet an integral part of the overall charm of the watch.

Overall, the Sterling 882.93092.01 is more than just a timekeeping device; it is a statement piece that showcases exceptional design, reliable technology, and outstanding craftsmanship. Whether worn at special occasions or in everyday scenarios, this watch is bound to impress and stand the test of time.