Sterling 882.93092.01 manual Automatic Water Make-Up Option, Initial Start-Up

Page 31

3-10 Automatic Water Make-Up Option

The chiller may be connected to an automatic make-up system if the optional package (pipe fittings, solenoid valve and 1/2” NPT city water make-up connection) is factory installed.

Note:

When the unit is selected with the optional, closed stainless steel tank, a

 

pressure reducing valve is added to the automatic water make-up option. This

 

valve is set to be full open at 5 psig (0.3 bar).

If the automatic make-up system is connected to a city water system, make provisions to prevent backflow contamination. Install an approved backflow preventer in accordance with local codes.

Caution! Adding straight city water into a glycol/water mixture dilutes the solution and eventually leads to system freeze-up. Damage from freeze-up is not covered by the warranty.

To prevent system freeze-up in automatic make-up applications, we recommend using either a chemical feeder or make-up reservoir to replenish glycol. Contact the sales department for more information about these configurations.

3-11 Initial Start-Up

Check the shipping papers against the serial tag to be sure chiller size, type and voltage is correct for the process that will be controlled. Portable chillers are built with a voltage specific compressor and cannot be re-wired for an alternate voltage.

Check the transformer primary voltage connections to be sure they are configured for the electrical power you are using. The voltage at the main power connection must read within plus or minus ten percent (±10%) of the voltage listed on the serial tag. Electrical connections must conform to all applicable codes.

GP Series Portable Chillers

Chapter 3: Installation

31 of 90

Page 30 Page 32
Image 31
Page 30 Page 32
Contents GP Series Portable Chillers Shipping Information Table of Contents Chapter Troubleshooting How to Use This Manual SafetySafety Symbols Used in this Manual Responsibility  Wear Safety Glasses and Work GlovesTypical Applications Functional DescriptionModels Covered in This Manual General DescriptionChilled Water Circuit System Control Refrigeration CircuitMechanical Features Standard FeaturesRefrigeration Features Electrical FeaturesCrankcase Heater Safety Devices and InterlocksController Features Other FeaturesHigh Pressure Cutout Flow Switch Optional FeaturesRemote Start/Stop Interlock Mounting Features Uncrating InstallationElectrical Connections Bypass Valve Considerations Process Water ConnectionsWater-Cooled Chiller Condensers Galvanic Corrosion ConsiderationsWater Treatment Considerations Condenser ConsiderationsAir-Cooled Chiller Condensers Typical GP20-50 Water Cooled Condenser ConnectionsRemote Air-Cooled Chiller Condensers Towards the condenser GPRC-40 GPRC-105 Discharge Line Sizing Refrigerant Charge Determination Remote Condenser Configurations Condenser Fan Three-Phase CompressorsChecking Motor Direction Water PumpsPart Number Description Water ReservoirSuggested Overhead Piping Configuration Pump Initial Start-Up Automatic Water Make-Up OptionPage Finishing Setup Setting Up Passwords Supervisor Password to complete the security setup Operation Panel Buttons, Indicator Lights, and SwitchesMicroprocessor Controller Main Status Screen Operator Setpoints Screen Status ScreensMain Chiller Status Screen GP Series Portable Chillers Operation Page Controller Setpoints Access LevelsGP Series Portable Chillers Operation Menu Screen Operator Setpoints Screen These configurations are described below Configuration SettingsWEB Optional Communications AlarmsMaintaining the Condenser MaintenanceFilter Cleaning LubricationMaintaining the Evaporator Preventative Maintenance ServiceEvaporator Process Piping Y-Strainer Identifying the Cause of a Problem TroubleshootingGP Series Portable Chillers Troubleshooting SC/W System fault GP Series Portable Chillers Troubleshooting Problem Possible cause Solution Non-Controller Related IssuesGP Series Portable Chillers Troubleshooting GP Series Portable Chillers Troubleshooting Returned Material Policy AppendixTechnical Assistance Sales Department Service DepartmentContract Department Air-Cooled Portable Chillers SpecificationsGPAC-40 GPAC-70 GPAC-105 GPAC-175 GPWC-20 Water-Cooled Portable ChillersGPWC-40 GPWC-70 GPWC-105 GPWC-175 Hertz Pump Curves Pump Curves, Flow, and Pressure ConsiderationsALL 60 Hz ALL 50 Hz ALL 50 Hz Calculating Chiller Nominal Flow and Pressure to Process Remote Air-Cooled Chiller Configurations Double Riser Detail Typical Ductwork for Air-Cooled Chillers Water column = Pascal GP Series Portable Chillers Appendix Piping Diagrams GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix

882.93092.01 specifications

The Sterling 882.93092.01 is an impressive timepiece that exemplifies the perfect blend of artistry and precision engineering. This elegant watch is a testament to the craftsmanship that defines the Sterling brand, making it a sought-after choice for both watch aficionados and casual wearers alike.

One of the main features of the Sterling 882.93092.01 is its exceptional movement technology. This watch is powered by a reliable automatic movement, ensuring accurate timekeeping without the need for battery replacements. The self-winding mechanism harnesses the natural motion of the wearer's wrist, providing a seamless and hassle-free experience.

The design of the Sterling 882.93092.01 is another standout characteristic. The watch features a stainless steel case that provides durability and a sleek aesthetic. The polished finish adds a touch of sophistication, making it suitable for both formal and casual settings. With a diameter that fits comfortably on the wrist, it is designed for effortless wear throughout the day.

Additionally, the face of the Sterling 882.93092.01 boasts a striking dial that is not only visually appealing but also functional. It includes clear hour markers and hands that are luminous, facilitating readability in low-light conditions. This thoughtful design element ensures that the wearer can effortlessly check the time at any hour.

Another notable aspect is the watch's water resistance. The Sterling 882.93092.01 is rated for water resistance, making it suitable for everyday wear, including light swimming and exposure to splashes. This feature enhances the watch’s practicality, allowing it to withstand the rigors of daily life without compromising its integrity.

Finally, the bracelet of the Sterling 882.93092.01 is crafted with comfort and style in mind. It features an adjustable clasp that allows for a customized fit, ensuring that the watch remains secure on the wrist. The combination of high-quality materials and impeccable design makes the bracelet an integral part of the overall charm of the watch.

Overall, the Sterling 882.93092.01 is more than just a timekeeping device; it is a statement piece that showcases exceptional design, reliable technology, and outstanding craftsmanship. Whether worn at special occasions or in everyday scenarios, this watch is bound to impress and stand the test of time.
Top Page Image Contents