Sterling 882.93092.01 manual Maintenance, Lubrication, Filter Cleaning, Maintaining the Condenser

Page 48

Chapter 5: Maintenance

5-1 Lubrication

Grease all fan motors, and pump motors that do not have permanently sealed bearings. Be sure to use an all-purpose industrial grease with a temperature reference of 185P F (85P C). Remove the grease relief plug (motors only) before adding grease, add grease until a small amount pours out, and replace the plug when finished.

Caution! Failure to remove the grease relief plug will result in dislodging the bearing grease seal, eventually causing bearing failure.

Refrigeration compressors are hermetically sealed and no lubrication is required.

5-2 Filter Cleaning

Air filter cleaning is important to keep your air-cooled portable chiller operating at peak efficiency and capacity. Clean the filters whenever they appear dirty, or at regularly scheduled intervals.

1.Turn the chiller off.

2.Remove the top side panel(s) to expose the condenser section.

3.Slide the filter rod to release it from the frame at the top and bottom.

4.Wash down the filter with clean water (preferably with a garden hose), directing the flow of water opposite the direction of airflow. If dirt is heavy, use a mild detergent and rinse well. Allow the filter to dry completely before replacing it on the chiller.

Note: Keep a spare air filter set on hand. Install and use it while cleaning).

Caution! Do not use compressed air to blow off a dirty filter. It will not clean very well, and the filter could be damaged. Never run the chiller without properly installed filters.

5-3 Maintaining the Condenser

Dirty condenser heat exchange surfaces reduce system capacity and efficiency.

Air- and Remote Air-Cooled Chillers

Brush or vacuum light dirt accumulations off the aluminum condenser fins. Avoid bending or damaging them. Heavy dirt accumulations on the fins may require professional cleaning.

Water-Cooled Chillers

Proper water treatment will greatly reduce cleaning intervals.

Coaxial Condensers (GPWC20-50).Remove dirt and slime in the condenser tube water side by reverse-circulating with a mild detergent and water solution. Remove mineral deposits by reverse circulating Liquid Inhibited Acid De-Scaling Solution (Part No. A0502600) through the water side of the condenser. Follow the directions on the container.

Shell & Tube Condensers (GPWC70-210).Remove dirt and slime in the condenser tube water side by cleaning with a nylon tube brush. Remove mineral deposits by reverse circulating Liquid Inhibited Acid De-Scaling Solution (Part No. A0502600) through the tube water side of the condenser. Follow the directions on the container.

The refrigerant side is sealed and requires no routine maintenance.

GP Series Portable Chillers

Chapter 5: Maintenance

48 of 90

Page 47 Page 49
Image 48
Page 47 Page 49
Contents GP Series Portable Chillers Shipping Information Table of Contents Chapter Troubleshooting Safety How to Use This ManualSafety Symbols Used in this Manual  Wear Safety Glasses and Work Gloves ResponsibilityFunctional Description Models Covered in This ManualGeneral Description Typical ApplicationsChilled Water Circuit Refrigeration Circuit System ControlStandard Features Mechanical FeaturesElectrical Features Refrigeration FeaturesSafety Devices and Interlocks Controller FeaturesOther Features Crankcase HeaterHigh Pressure Cutout Optional Features Flow SwitchRemote Start/Stop Interlock Mounting Features Installation UncratingElectrical Connections Process Water Connections Bypass Valve ConsiderationsGalvanic Corrosion Considerations Water Treatment ConsiderationsCondenser Considerations Water-Cooled Chiller CondensersTypical GP20-50 Water Cooled Condenser Connections Air-Cooled Chiller CondensersRemote Air-Cooled Chiller Condensers Towards the condenser GPRC-40 GPRC-105 Discharge Line Sizing Refrigerant Charge Determination Remote Condenser Configurations Three-Phase Compressors Checking Motor DirectionWater Pumps Condenser FanWater Reservoir Part Number DescriptionSuggested Overhead Piping Configuration Pump Automatic Water Make-Up Option Initial Start-UpPage Finishing Setup Setting Up Passwords Supervisor Password to complete the security setup Panel Buttons, Indicator Lights, and Switches OperationMicroprocessor Controller Main Status Screen Status Screens Operator Setpoints ScreenMain Chiller Status Screen GP Series Portable Chillers Operation Page Access Levels Controller SetpointsGP Series Portable Chillers Operation Menu Screen Operator Setpoints Screen Configuration Settings These configurations are described belowWEB Alarms Optional CommunicationsMaintenance Filter CleaningLubrication Maintaining the CondenserPreventative Maintenance Service Maintaining the EvaporatorEvaporator Process Piping Y-Strainer Troubleshooting Identifying the Cause of a ProblemGP Series Portable Chillers Troubleshooting SC/W System fault GP Series Portable Chillers Troubleshooting Non-Controller Related Issues Problem Possible cause SolutionGP Series Portable Chillers Troubleshooting GP Series Portable Chillers Troubleshooting Appendix Returned Material PolicyTechnical Assistance Service Department Sales DepartmentContract Department Specifications Air-Cooled Portable ChillersGPAC-40 GPAC-70 GPAC-105 GPAC-175 Water-Cooled Portable Chillers GPWC-20GPWC-40 GPWC-70 GPWC-105 GPWC-175 Pump Curves, Flow, and Pressure Considerations Hertz Pump CurvesALL 60 Hz ALL 50 Hz ALL 50 Hz Calculating Chiller Nominal Flow and Pressure to Process Remote Air-Cooled Chiller Configurations Double Riser Detail Typical Ductwork for Air-Cooled Chillers Water column = Pascal GP Series Portable Chillers Appendix Piping Diagrams GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix GP Series Portable Chillers Appendix

882.93092.01 specifications

The Sterling 882.93092.01 is an impressive timepiece that exemplifies the perfect blend of artistry and precision engineering. This elegant watch is a testament to the craftsmanship that defines the Sterling brand, making it a sought-after choice for both watch aficionados and casual wearers alike.

One of the main features of the Sterling 882.93092.01 is its exceptional movement technology. This watch is powered by a reliable automatic movement, ensuring accurate timekeeping without the need for battery replacements. The self-winding mechanism harnesses the natural motion of the wearer's wrist, providing a seamless and hassle-free experience.

The design of the Sterling 882.93092.01 is another standout characteristic. The watch features a stainless steel case that provides durability and a sleek aesthetic. The polished finish adds a touch of sophistication, making it suitable for both formal and casual settings. With a diameter that fits comfortably on the wrist, it is designed for effortless wear throughout the day.

Additionally, the face of the Sterling 882.93092.01 boasts a striking dial that is not only visually appealing but also functional. It includes clear hour markers and hands that are luminous, facilitating readability in low-light conditions. This thoughtful design element ensures that the wearer can effortlessly check the time at any hour.

Another notable aspect is the watch's water resistance. The Sterling 882.93092.01 is rated for water resistance, making it suitable for everyday wear, including light swimming and exposure to splashes. This feature enhances the watch’s practicality, allowing it to withstand the rigors of daily life without compromising its integrity.

Finally, the bracelet of the Sterling 882.93092.01 is crafted with comfort and style in mind. It features an adjustable clasp that allows for a customized fit, ensuring that the watch remains secure on the wrist. The combination of high-quality materials and impeccable design makes the bracelet an integral part of the overall charm of the watch.

Overall, the Sterling 882.93092.01 is more than just a timekeeping device; it is a statement piece that showcases exceptional design, reliable technology, and outstanding craftsmanship. Whether worn at special occasions or in everyday scenarios, this watch is bound to impress and stand the test of time.
Top Page Image Contents