GE JVM1665SNSS warranty A4. Mount the Oven, A3. Assemble and Install Adapter

Page 13

Installation Instructions

A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET

You need to drill holes for the top support screws,

a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adapter.

•Read the instructions on the top cabinet template.

•Tape it underneath the top cabinet.

•Drill the holes, following the instructions on the top cabinet template.

A4. MOUNT THE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN.

IMPORTANT: Do not grip or use handle during installation.

NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.

NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case damage may occur from over tightening screws.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

A3. ASSEMBLE AND INSTALL ADAPTER

Damper

Exhaust

Adapter

Blower Plate

Back of

Oven

NOTE: When mounting

the oven, thread power cord through hole in bottom

of top cabinet. Keep it tight throughout Steps 1–3.

Do not pinch cord or lift oven by pulling cord.

1

Lift oven, tilt it forward and hook slots at back bottom edge onto two lower tabs of mounting plate.

NOTE: On some models, the exhaust adapter and damper assembly may already be assembled to the oven.

1Place the oven in its upright position, with the top of the unit facing up.

NOTE: Make sure the blower fan blades are visible and are pointing up.

2Insert the tabs on each side of the damper into the holes at the inside rear of the adapter.

3Attach the exhaust adapter to the blower plate with the two bronze metal screws provided.

Make sure that the damper pivots easily before mounting oven.

You will need to make adjustments to assure proper alignment with your house exhaust duct after the oven is installed.

2Rotate front of oven up against cabinet bottom.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Read these instructions completely and carefully Before YOU BeginInstructions for local inspector’s use Contents Installation InstructionsIt is recommended that two people install this product Important Safety InstructionsElectrical Requirements IMPORTANT-PLEASE Read CarefullyOutside TOP Exhaust Example only Hood ExhaustOutside Back Exhaust Example only Total LengthMaximum duct length Exhaust connectionElbows, transitions, wall and roof caps, etc Nothing is blocking the ductsParts Included Or replacement is the responsibility of the customerHardware Packet Additional PartsMounting Space Tools YOU will NeedFinding the Wall Studs Placement of the Mounting PlateOven Must be Connected to AT Least ONE Wall Stud Carton StyrofoamOven Must be Level Determining Wall Plate Location Under Your CabinetAligning the Wall Plate To support the weight of the ovenFour holes must be used for mounting See Recirculating NON-VENTED DuctlessA1. Attach the Mounting Plate to the Wall Installation OverviewTo use toggle bolts Spacing for Toggles More Than Wall ThicknessOven, thread power cord through hole in bottom A3. Assemble and Install AdapterA4. Mount the Oven A2. USE TOP Cabinet Template for Preparation of TOP CabinetA6. Connecting Ductwork A5. Adjust the Exhaust AdapterExhaust Adapter B2. Attach the Exhaust Adapter To the Oven Rear PanelGuide Guide Locking TabsB4. USE TOP Cabinet Template for Preparation of TOP Cabinet B3. Attach the Mounting Plate to the WallPlate Wall Bolt EndPlace the blower unit back into the opening Rotate blower unit counterclockwiseB6. Mount the Oven Important Do not grip or use handle during installationCord Attach the oven to the top cabinet by insertingC2. USE TOP Cabinet Template for Preparation of TOP Cabinet C1. Attach the Mounting Plate to the WallBlower Plate Screws Back of Oven Blower Motor Screw C3. Adapting Blower For RecirculationRetaining Flange Blower Plate RollC3. Adapting Blower for Recirculation C4. Mount the OvenCharcoal Filter C5. Installing the Charcoal FilterInsert mesh-side up Before YOU USE Your Oven Page Lea estas instrucciones completa y cuidadosamente Antes DE EmpezarEstas instrucciones con el consumidor Instrucciones para futura referenciaInformación general ContenidoGuía de instalación paso por paso Requisitos Eléctricos Instrucciones DE Seguridad ImportantesImportante POR FAVOR, LEA CUIDADOSAMENTE. EN POS La clasificación del producto es de 120 vatios CA ACEscape Superior Externo Ejemplo Solamente Campana DE EscapeEscape Posterior Externo Ejemplo Solamente PiesLongitud máxima del conducto Conexiones de escapeLos codos, transiciones, paredes y tapas Total red de conductos = PiesPartes Incluidas Daños Envío InstalaciónPaquete DE Elementos Partes AdicionalesEspacio DE Montaje Herramientas QUE NecesitaráNotas Si el espacio entre los gabinetes es mayor deCómo Encontrar LOS Postes DE Viga EN LA Pared Cómo Colocar EL Plato DE MontajeCaja Poliestireno CentroEL Horno Debe Quedar Nivelado Posición del plato debajo de gabinetes de fondo planoSe describió en el Paso D Plato de montajeNota Todavía no Monte EL Plato Cómo Alinear EL Plato DE Montaje Sobre LA ParedDel propietario para obtener el número del kit Escape superior exterior Conducto verticalEn los modelos despachados con escape sin ventilación A1. Cómo Adherir LA Placa DE Montaje a LA Pared Perspectiva General DE LA InstalaciónPara usar los tornillos basculantes A3. Ensamblaje E Instalación DEL Adaptador A4. Cómo Montar EL HornoPéguelo debajo del gabinete superior DOS Personas Instalen Este HornoA6. Cómo Conectar EL Conducto A5. Cómo Ajustar EL Adaptador DE EscapeContinuación El gabinete superiorDe escape El regulador de tiro gire librementeGuía Guía Orejillas De cierre Mariposa B3. Cómo Adherir EL Plato DE Montaje a LA ParedColoque la unidad del calefactor de nuevo en la abertura Se monte al nivel del fondo del gabinete B6. Montaje DEL HornoTornillos autoalineables Parte superior del horno De montajeRemueva las mariposas del basculante de los tornillos C1. Cómo Adherir LA Placa DE Montaje a LA ParedAlas de mariposa Tornillo deNota El adaptador de escape con calefactor C3. Cómo Adaptar EL Calefactor Para LA RecirculaciónPlato del calefactor RuedeC4. Montaje DEL Horno Inserte la malla hacia abajo C5. Cómo Instalar EL Filtro DE CarbonillaCerciórese de que el horno ha sido instalado Antes DE Comenzar a Usar SU HornoDe acuerdo con las instrucciones Lea el Manual del PropietarioImpreso en China

JVM1665, JVM1665SNSS specifications

The GE JVM1665SNSS is a versatile microwave oven that combines functionality and style, making it an excellent addition to any kitchen. This model is part of the GE lineup, recognized for its commitment to quality and innovation. The JVM1665SNSS is designed with a sleek stainless steel finish, adding a modern touch to your kitchen decor while being easy to clean.

One of the standout features of the GE JVM1665SNSS is its 1.6 cubic feet capacity, which provides ample space for cooking a variety of dishes. Its 1000 watts of power ensures efficient heating, allowing for quick meal preparation. The microwave comes equipped with a turntable, ensuring even cooking results for all food items.

The JVM1665SNSS features multiple cooking modes and options, including auto-reheat, defrost, and sensor cooking. The sensor cooking controls automatically adjust cooking time based on the moisture level in the food, ensuring optimal results without the guesswork. This technology not only enhances convenience but also helps prevent overcooking.

Another notable characteristic of this microwave is its ease of use. The simple control panel includes an intuitive layout with easy-to-read buttons that allow users to quickly select cooking programs and set times. Additionally, the microwave includes a powerful exhaust fan with multiple speed settings, effectively removing smoke, steam, and odors from the kitchen.

For added safety, the JVM1665SNSS features a child lock function, preventing unintended use by young children. The microwave also comes with a removable grease filter, which ensures that the kitchen environment remains clean and fresh during cooking.

This model is compatible with venting options, allowing it to be installed as either a recirculating or externally vented unit, providing flexibility in kitchen design. Overall, the GE JVM1665SNSS is an impressive microwave that combines modern features, advanced technologies, and user-friendly characteristics, making it a reliable choice for any home cook looking to enhance their cooking experience.
Top Page Image Contents