GE JVM1665SNSS warranty Tools YOU will Need, Mounting Space

Page 7

Installation Instructions

TOOLS YOU WILL NEED

 

 

Ruler or tape measure

# 1 and #2 Phillips screwdriver

Pencil

and straight edge

 

 

 

Carpenter square (optional)

Tin snips (for cutting damper, if required)

Gloves

Scissors

(to cut template, if necessary) Electric drill with 3⁄16″ , 7⁄16″ , 3⁄8″ , 1⁄2″ and 5⁄8″ drill bits

Saw (saber, hole or keyhole)

Stud finder or Hammer (optional)

Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only)

Safety goggles

Duct and masking tape

Level

MOUNTING SPACE

NOTES:

NOTE: Maximum cabinet depth is 13".

16-1⁄4″

30″

2″

66″ or more from the floor to the top of the oven

Bottom edge of cabinet needs to be 30″ or more from the cooking surface

30″ min.

Backsplash

•The space between the cabinets must be 30″ wide and free of obstructions.

•If the space between the cabinets is greater than 30″ , a Filler Panel Kit may be used to fill in the gap between the oven and the cabinets. Your Owner’s Manual contains the kit number for your model.

•This oven is for installation over ranges up to 36″ wide.

•If you are going to vent your oven to the outside, see Hood Exhaust Section for exhaust duct preparation.

•When installing the oven beneath smooth, flat cabinets, be careful to follow the instructions on the top cabinet template for power cord clearance.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Read these instructions completely and carefully Before YOU BeginInstructions for local inspector’s use Contents Installation InstructionsIMPORTANT-PLEASE Read Carefully Important Safety InstructionsIt is recommended that two people install this product Electrical RequirementsTotal Length Hood ExhaustOutside TOP Exhaust Example only Outside Back Exhaust Example onlyNothing is blocking the ducts Exhaust connectionMaximum duct length Elbows, transitions, wall and roof caps, etcAdditional Parts Or replacement is the responsibility of the customerParts Included Hardware PacketMounting Space Tools YOU will NeedCarton Styrofoam Placement of the Mounting PlateFinding the Wall Studs Oven Must be Connected to AT Least ONE Wall StudOven Must be Level Determining Wall Plate Location Under Your CabinetAligning the Wall Plate To support the weight of the ovenFour holes must be used for mounting See Recirculating NON-VENTED DuctlessSpacing for Toggles More Than Wall Thickness Installation OverviewA1. Attach the Mounting Plate to the Wall To use toggle boltsA2. USE TOP Cabinet Template for Preparation of TOP Cabinet A3. Assemble and Install AdapterOven, thread power cord through hole in bottom A4. Mount the OvenA6. Connecting Ductwork A5. Adjust the Exhaust AdapterGuide Locking Tabs B2. Attach the Exhaust Adapter To the Oven Rear PanelExhaust Adapter GuideWall Bolt End B3. Attach the Mounting Plate to the WallB4. USE TOP Cabinet Template for Preparation of TOP Cabinet PlatePlace the blower unit back into the opening Rotate blower unit counterclockwiseAttach the oven to the top cabinet by inserting Important Do not grip or use handle during installationB6. Mount the Oven CordC2. USE TOP Cabinet Template for Preparation of TOP Cabinet C1. Attach the Mounting Plate to the WallRoll C3. Adapting Blower For RecirculationBlower Plate Screws Back of Oven Blower Motor Screw Retaining Flange Blower PlateC3. Adapting Blower for Recirculation C4. Mount the OvenCharcoal Filter C5. Installing the Charcoal FilterInsert mesh-side up Before YOU USE Your Oven Page Instrucciones para futura referencia Antes DE EmpezarLea estas instrucciones completa y cuidadosamente Estas instrucciones con el consumidorInformación general ContenidoGuía de instalación paso por paso La clasificación del producto es de 120 vatios CA AC Instrucciones DE Seguridad ImportantesRequisitos Eléctricos Importante POR FAVOR, LEA CUIDADOSAMENTE. EN POSPies Campana DE EscapeEscape Superior Externo Ejemplo Solamente Escape Posterior Externo Ejemplo SolamenteTotal red de conductos = Pies Conexiones de escapeLongitud máxima del conducto Los codos, transiciones, paredes y tapasPartes Adicionales Daños Envío InstalaciónPartes Incluidas Paquete DE ElementosSi el espacio entre los gabinetes es mayor de Herramientas QUE NecesitaráEspacio DE Montaje NotasCentro Cómo Colocar EL Plato DE MontajeCómo Encontrar LOS Postes DE Viga EN LA Pared Caja PoliestirenoPlato de montaje Posición del plato debajo de gabinetes de fondo planoEL Horno Debe Quedar Nivelado Se describió en el Paso DNota Todavía no Monte EL Plato Cómo Alinear EL Plato DE Montaje Sobre LA ParedDel propietario para obtener el número del kit Escape superior exterior Conducto verticalEn los modelos despachados con escape sin ventilación A1. Cómo Adherir LA Placa DE Montaje a LA Pared Perspectiva General DE LA InstalaciónPara usar los tornillos basculantes DOS Personas Instalen Este Horno A4. Cómo Montar EL HornoA3. Ensamblaje E Instalación DEL Adaptador Péguelo debajo del gabinete superiorEl gabinete superior A5. Cómo Ajustar EL Adaptador DE EscapeA6. Cómo Conectar EL Conducto ContinuaciónDe escape El regulador de tiro gire librementeGuía Guía Orejillas De cierre Mariposa B3. Cómo Adherir EL Plato DE Montaje a LA ParedColoque la unidad del calefactor de nuevo en la abertura De montaje B6. Montaje DEL HornoSe monte al nivel del fondo del gabinete Tornillos autoalineables Parte superior del hornoTornillo de C1. Cómo Adherir LA Placa DE Montaje a LA ParedRemueva las mariposas del basculante de los tornillos Alas de mariposaRuede C3. Cómo Adaptar EL Calefactor Para LA RecirculaciónNota El adaptador de escape con calefactor Plato del calefactorC4. Montaje DEL Horno Inserte la malla hacia abajo C5. Cómo Instalar EL Filtro DE CarbonillaLea el Manual del Propietario Antes DE Comenzar a Usar SU HornoCerciórese de que el horno ha sido instalado De acuerdo con las instruccionesImpreso en China

JVM1665, JVM1665SNSS specifications

The GE JVM1665SNSS is a versatile microwave oven that combines functionality and style, making it an excellent addition to any kitchen. This model is part of the GE lineup, recognized for its commitment to quality and innovation. The JVM1665SNSS is designed with a sleek stainless steel finish, adding a modern touch to your kitchen decor while being easy to clean.

One of the standout features of the GE JVM1665SNSS is its 1.6 cubic feet capacity, which provides ample space for cooking a variety of dishes. Its 1000 watts of power ensures efficient heating, allowing for quick meal preparation. The microwave comes equipped with a turntable, ensuring even cooking results for all food items.

The JVM1665SNSS features multiple cooking modes and options, including auto-reheat, defrost, and sensor cooking. The sensor cooking controls automatically adjust cooking time based on the moisture level in the food, ensuring optimal results without the guesswork. This technology not only enhances convenience but also helps prevent overcooking.

Another notable characteristic of this microwave is its ease of use. The simple control panel includes an intuitive layout with easy-to-read buttons that allow users to quickly select cooking programs and set times. Additionally, the microwave includes a powerful exhaust fan with multiple speed settings, effectively removing smoke, steam, and odors from the kitchen.

For added safety, the JVM1665SNSS features a child lock function, preventing unintended use by young children. The microwave also comes with a removable grease filter, which ensures that the kitchen environment remains clean and fresh during cooking.

This model is compatible with venting options, allowing it to be installed as either a recirculating or externally vented unit, providing flexibility in kitchen design. Overall, the GE JVM1665SNSS is an impressive microwave that combines modern features, advanced technologies, and user-friendly characteristics, making it a reliable choice for any home cook looking to enhance their cooking experience.
Top Page Image Contents