GE JVM1665SNSS warranty Installation Overview, A1. Attach the Mounting Plate to the Wall

Page 12

Installation Instructions

A

OUTSIDE TOP EXHAUST (Vertical Duct)

INSTALLATION OVERVIEW

A1. Attach Mounting Plate to Wall

A2. Prepare Top Cabinet

A3. Install Adapter

A4. Mount Oven

A5. Adjust Exhaust Adapter

A6. Connect Ductwork

A1. ATTACH THE MOUNTING PLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.

1Remove the toggle wings from the bolts.

2Insert the bolts into the mounting plate

through the holes designated to go into drywall and reattach the toggle wings to 3⁄ 4″ onto each bolt.

To use toggle bolts:

Spacing for Toggles

More Than Wall

Thickness

Mounting

Toggle Wings

Toggle

Plate

Bolt

Wall

Bolt End

3Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.

NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall.

4Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Before YOU Begin Read these instructions completely and carefullyInstructions for local inspector’s use Installation Instructions ContentsImportant Safety Instructions It is recommended that two people install this productElectrical Requirements IMPORTANT-PLEASE Read CarefullyHood Exhaust Outside TOP Exhaust Example onlyOutside Back Exhaust Example only Total LengthExhaust connection Maximum duct lengthElbows, transitions, wall and roof caps, etc Nothing is blocking the ductsOr replacement is the responsibility of the customer Parts IncludedHardware Packet Additional PartsTools YOU will Need Mounting SpacePlacement of the Mounting Plate Finding the Wall StudsOven Must be Connected to AT Least ONE Wall Stud Carton StyrofoamDetermining Wall Plate Location Under Your Cabinet Oven Must be LevelTo support the weight of the oven Aligning the Wall PlateFour holes must be used for mounting Recirculating NON-VENTED Ductless SeeInstallation Overview A1. Attach the Mounting Plate to the WallTo use toggle bolts Spacing for Toggles More Than Wall ThicknessA3. Assemble and Install Adapter Oven, thread power cord through hole in bottomA4. Mount the Oven A2. USE TOP Cabinet Template for Preparation of TOP CabinetA5. Adjust the Exhaust Adapter A6. Connecting DuctworkB2. Attach the Exhaust Adapter To the Oven Rear Panel Exhaust AdapterGuide Guide Locking TabsB3. Attach the Mounting Plate to the Wall B4. USE TOP Cabinet Template for Preparation of TOP CabinetPlate Wall Bolt EndRotate blower unit counterclockwise Place the blower unit back into the openingImportant Do not grip or use handle during installation B6. Mount the OvenCord Attach the oven to the top cabinet by insertingC1. Attach the Mounting Plate to the Wall C2. USE TOP Cabinet Template for Preparation of TOP CabinetC3. Adapting Blower For Recirculation Blower Plate Screws Back of Oven Blower Motor ScrewRetaining Flange Blower Plate RollC4. Mount the Oven C3. Adapting Blower for RecirculationC5. Installing the Charcoal Filter Charcoal FilterInsert mesh-side up Before YOU USE Your Oven Page Antes DE Empezar Lea estas instrucciones completa y cuidadosamenteEstas instrucciones con el consumidor Instrucciones para futura referenciaContenido Información generalGuía de instalación paso por paso Instrucciones DE Seguridad Importantes Requisitos EléctricosImportante POR FAVOR, LEA CUIDADOSAMENTE. EN POS La clasificación del producto es de 120 vatios CA ACCampana DE Escape Escape Superior Externo Ejemplo SolamenteEscape Posterior Externo Ejemplo Solamente PiesConexiones de escape Longitud máxima del conductoLos codos, transiciones, paredes y tapas Total red de conductos = PiesDaños Envío Instalación Partes IncluidasPaquete DE Elementos Partes AdicionalesHerramientas QUE Necesitará Espacio DE MontajeNotas Si el espacio entre los gabinetes es mayor deCómo Colocar EL Plato DE Montaje Cómo Encontrar LOS Postes DE Viga EN LA ParedCaja Poliestireno CentroPosición del plato debajo de gabinetes de fondo plano EL Horno Debe Quedar NiveladoSe describió en el Paso D Plato de montajeCómo Alinear EL Plato DE Montaje Sobre LA Pared Nota Todavía no Monte EL PlatoEscape superior exterior Conducto vertical Del propietario para obtener el número del kitEn los modelos despachados con escape sin ventilación Perspectiva General DE LA Instalación A1. Cómo Adherir LA Placa DE Montaje a LA ParedPara usar los tornillos basculantes A4. Cómo Montar EL Horno A3. Ensamblaje E Instalación DEL AdaptadorPéguelo debajo del gabinete superior DOS Personas Instalen Este HornoA5. Cómo Ajustar EL Adaptador DE Escape A6. Cómo Conectar EL ConductoContinuación El gabinete superiorEl regulador de tiro gire libremente De escapeGuía Guía Orejillas De cierre B3. Cómo Adherir EL Plato DE Montaje a LA Pared MariposaColoque la unidad del calefactor de nuevo en la abertura B6. Montaje DEL Horno Se monte al nivel del fondo del gabineteTornillos autoalineables Parte superior del horno De montajeC1. Cómo Adherir LA Placa DE Montaje a LA Pared Remueva las mariposas del basculante de los tornillosAlas de mariposa Tornillo deC3. Cómo Adaptar EL Calefactor Para LA Recirculación Nota El adaptador de escape con calefactorPlato del calefactor RuedeC4. Montaje DEL Horno C5. Cómo Instalar EL Filtro DE Carbonilla Inserte la malla hacia abajoAntes DE Comenzar a Usar SU Horno Cerciórese de que el horno ha sido instaladoDe acuerdo con las instrucciones Lea el Manual del PropietarioImpreso en China

JVM1665, JVM1665SNSS specifications

The GE JVM1665SNSS is a versatile microwave oven that combines functionality and style, making it an excellent addition to any kitchen. This model is part of the GE lineup, recognized for its commitment to quality and innovation. The JVM1665SNSS is designed with a sleek stainless steel finish, adding a modern touch to your kitchen decor while being easy to clean.

One of the standout features of the GE JVM1665SNSS is its 1.6 cubic feet capacity, which provides ample space for cooking a variety of dishes. Its 1000 watts of power ensures efficient heating, allowing for quick meal preparation. The microwave comes equipped with a turntable, ensuring even cooking results for all food items.

The JVM1665SNSS features multiple cooking modes and options, including auto-reheat, defrost, and sensor cooking. The sensor cooking controls automatically adjust cooking time based on the moisture level in the food, ensuring optimal results without the guesswork. This technology not only enhances convenience but also helps prevent overcooking.

Another notable characteristic of this microwave is its ease of use. The simple control panel includes an intuitive layout with easy-to-read buttons that allow users to quickly select cooking programs and set times. Additionally, the microwave includes a powerful exhaust fan with multiple speed settings, effectively removing smoke, steam, and odors from the kitchen.

For added safety, the JVM1665SNSS features a child lock function, preventing unintended use by young children. The microwave also comes with a removable grease filter, which ensures that the kitchen environment remains clean and fresh during cooking.

This model is compatible with venting options, allowing it to be installed as either a recirculating or externally vented unit, providing flexibility in kitchen design. Overall, the GE JVM1665SNSS is an impressive microwave that combines modern features, advanced technologies, and user-friendly characteristics, making it a reliable choice for any home cook looking to enhance their cooking experience.
Top Page Image Contents