GE JVM1665SNSS warranty C4. Mount the Oven, C3. Adapting Blower for Recirculation

Page 21

Installation Instructions

C3. ADAPTING BLOWER FOR RECIRCULATION (continued)

5Place the blower unit back into the opening.

CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched.

6Replace blower plate and replace screws for blower plate and blower motor removed in Step 1.

Blower Plate Screws

Blower Plate

Back of Oven

NOTE: When mounting the oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord.

2Rotate front of oven up against cabinet bottom.

1

Lift oven, tilt it forward and hook slots at back bottom edge onto two lower tabs of mounting plate.

Blower Motor Screw

C4. MOUNT THE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN.

IMPORTANT: Do not grip or use handle during installation.

NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.

NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case damage may occur from over tightening screws.

Cabinet Front

Cabinet Bottom Shelf

Filler Block

Equivalent to Depth of Cabinet Recess

Self-Aligning Screw

Oven Top

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Before YOU Begin Read these instructions completely and carefullyInstructions for local inspector’s use Contents Installation InstructionsIt is recommended that two people install this product Important Safety InstructionsElectrical Requirements IMPORTANT-PLEASE Read CarefullyOutside TOP Exhaust Example only Hood ExhaustOutside Back Exhaust Example only Total LengthMaximum duct length Exhaust connectionElbows, transitions, wall and roof caps, etc Nothing is blocking the ductsParts Included Or replacement is the responsibility of the customerHardware Packet Additional PartsMounting Space Tools YOU will NeedFinding the Wall Studs Placement of the Mounting PlateOven Must be Connected to AT Least ONE Wall Stud Carton StyrofoamOven Must be Level Determining Wall Plate Location Under Your CabinetTo support the weight of the oven Aligning the Wall PlateFour holes must be used for mounting See Recirculating NON-VENTED DuctlessA1. Attach the Mounting Plate to the Wall Installation OverviewTo use toggle bolts Spacing for Toggles More Than Wall ThicknessOven, thread power cord through hole in bottom A3. Assemble and Install AdapterA4. Mount the Oven A2. USE TOP Cabinet Template for Preparation of TOP CabinetA6. Connecting Ductwork A5. Adjust the Exhaust AdapterExhaust Adapter B2. Attach the Exhaust Adapter To the Oven Rear PanelGuide Guide Locking TabsB4. USE TOP Cabinet Template for Preparation of TOP Cabinet B3. Attach the Mounting Plate to the WallPlate Wall Bolt EndPlace the blower unit back into the opening Rotate blower unit counterclockwiseB6. Mount the Oven Important Do not grip or use handle during installationCord Attach the oven to the top cabinet by insertingC2. USE TOP Cabinet Template for Preparation of TOP Cabinet C1. Attach the Mounting Plate to the WallBlower Plate Screws Back of Oven Blower Motor Screw C3. Adapting Blower For RecirculationRetaining Flange Blower Plate RollC3. Adapting Blower for Recirculation C4. Mount the OvenC5. Installing the Charcoal Filter Charcoal FilterInsert mesh-side up Before YOU USE Your Oven Page Lea estas instrucciones completa y cuidadosamente Antes DE EmpezarEstas instrucciones con el consumidor Instrucciones para futura referenciaContenido Información generalGuía de instalación paso por paso Requisitos Eléctricos Instrucciones DE Seguridad ImportantesImportante POR FAVOR, LEA CUIDADOSAMENTE. EN POS La clasificación del producto es de 120 vatios CA ACEscape Superior Externo Ejemplo Solamente Campana DE EscapeEscape Posterior Externo Ejemplo Solamente PiesLongitud máxima del conducto Conexiones de escapeLos codos, transiciones, paredes y tapas Total red de conductos = PiesPartes Incluidas Daños Envío InstalaciónPaquete DE Elementos Partes AdicionalesEspacio DE Montaje Herramientas QUE NecesitaráNotas Si el espacio entre los gabinetes es mayor deCómo Encontrar LOS Postes DE Viga EN LA Pared Cómo Colocar EL Plato DE MontajeCaja Poliestireno CentroEL Horno Debe Quedar Nivelado Posición del plato debajo de gabinetes de fondo planoSe describió en el Paso D Plato de montajeNota Todavía no Monte EL Plato Cómo Alinear EL Plato DE Montaje Sobre LA ParedEscape superior exterior Conducto vertical Del propietario para obtener el número del kitEn los modelos despachados con escape sin ventilación Perspectiva General DE LA Instalación A1. Cómo Adherir LA Placa DE Montaje a LA ParedPara usar los tornillos basculantes A3. Ensamblaje E Instalación DEL Adaptador A4. Cómo Montar EL HornoPéguelo debajo del gabinete superior DOS Personas Instalen Este HornoA6. Cómo Conectar EL Conducto A5. Cómo Ajustar EL Adaptador DE EscapeContinuación El gabinete superiorEl regulador de tiro gire libremente De escapeGuía Guía Orejillas De cierre Mariposa B3. Cómo Adherir EL Plato DE Montaje a LA ParedColoque la unidad del calefactor de nuevo en la abertura Se monte al nivel del fondo del gabinete B6. Montaje DEL HornoTornillos autoalineables Parte superior del horno De montajeRemueva las mariposas del basculante de los tornillos C1. Cómo Adherir LA Placa DE Montaje a LA ParedAlas de mariposa Tornillo deNota El adaptador de escape con calefactor C3. Cómo Adaptar EL Calefactor Para LA RecirculaciónPlato del calefactor RuedeC4. Montaje DEL Horno Inserte la malla hacia abajo C5. Cómo Instalar EL Filtro DE CarbonillaCerciórese de que el horno ha sido instalado Antes DE Comenzar a Usar SU HornoDe acuerdo con las instrucciones Lea el Manual del PropietarioImpreso en China

JVM1665, JVM1665SNSS specifications

The GE JVM1665SNSS is a versatile microwave oven that combines functionality and style, making it an excellent addition to any kitchen. This model is part of the GE lineup, recognized for its commitment to quality and innovation. The JVM1665SNSS is designed with a sleek stainless steel finish, adding a modern touch to your kitchen decor while being easy to clean.

One of the standout features of the GE JVM1665SNSS is its 1.6 cubic feet capacity, which provides ample space for cooking a variety of dishes. Its 1000 watts of power ensures efficient heating, allowing for quick meal preparation. The microwave comes equipped with a turntable, ensuring even cooking results for all food items.

The JVM1665SNSS features multiple cooking modes and options, including auto-reheat, defrost, and sensor cooking. The sensor cooking controls automatically adjust cooking time based on the moisture level in the food, ensuring optimal results without the guesswork. This technology not only enhances convenience but also helps prevent overcooking.

Another notable characteristic of this microwave is its ease of use. The simple control panel includes an intuitive layout with easy-to-read buttons that allow users to quickly select cooking programs and set times. Additionally, the microwave includes a powerful exhaust fan with multiple speed settings, effectively removing smoke, steam, and odors from the kitchen.

For added safety, the JVM1665SNSS features a child lock function, preventing unintended use by young children. The microwave also comes with a removable grease filter, which ensures that the kitchen environment remains clean and fresh during cooking.

This model is compatible with venting options, allowing it to be installed as either a recirculating or externally vented unit, providing flexibility in kitchen design. Overall, the GE JVM1665SNSS is an impressive microwave that combines modern features, advanced technologies, and user-friendly characteristics, making it a reliable choice for any home cook looking to enhance their cooking experience.
Top Page Image Contents