GE JCKS10, JCTP30, JCKP70 Securing the Oven in the Opening, C1 Sliding the Oven Into the Opening

Page 10

Installation Instructions

C

Securing the Oven in the Opening

C1 Sliding the Oven Into the Opening

a. Loop (do not tie) a 91 cm (36”) string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven.

Pull out on string loop while pushing the oven into the cabinet

b. Lift oven into cabinet cutout using the oven opening as a grip. Carefully push against oven front frame. Do not push against outside edges.

c. As you slide the oven back, pull the string so that the conduit will lie on top of the oven in a natural loop.

d. When you are sure the conduit is out of the way, slide the oven 3/4 way back into the opening. Remove the string by pulling on one end of the loop.

C2 Drilling the Pilot Holes and Mounting the Oven

NOTE: Before drilling the pilot holes, make sure the oven is pushed as far back into the opening as it will go and is centered.

a. Drill through the mounting holes (top and bottom) of the side trim, for the #8 screws provided.

Mounting

The screws must

Hole

be a minimum

Locations

of 6 mm (1/4”)

(Hole

Locations

from the front of

may vary)

the cutout.

 

WARNING: Mounting

screws must be used. Failure to do so could result in the oven

falling out of the cabinet, causing serious injury.

b. Secure the oven to cabinet with screws provided.

NOTE: If the cabinet is particle board, you must use #8 x 19 mm (3/4”) particle board screws. These may be purchased at any hardware store.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Materials Needed Before You BeginParts Included Tools NeededFor Your Safety Electrical RequirementsPre-Installation Checklist Do not Lift the Door By the HandleCutout for 27″ 68.6 cm Single Built-In Ovens only For JCKP30, JCKP70, JCKS10, PCK916, PCK920 models onlyCutout for 30″ 76.2 cm Single Built-In Ovens only For JCTP30, JCTP70, PCT916, PCT920 models onlyCutout for 27″ 68.6 cm Single Built-In Ovens only Under CounterCutout for 30″ 76.2 cm Single Built-In Ovens only For JCTP30, JCTP70, PCT916, PCT920 models only Connection of aluminum house wiring to copper leads can Electrical ConnectionsSecuring the Oven in the Opening C1 Sliding the Oven Into the OpeningC3 Preparing for the Bottom Trim Installation Replacing the Oven Door Operation Checklist Pre-Test ChecklistPage Page ’essai pour vérification de Liste ’essai avant vérification de ListeFour du porte la de place en Remise Four du porte la FermezInférieure garniture la de Montage du Préparation ’ouverture dans four du Fixation AvertissementÉlectrique Raccordement Bague UneDirectives aux vous-Reportez .simple encastré Po 30 comptoir d’un dessous au Po 27 comptoir d’un dessous au Po 30 simples SeulementEncastrés fours pour Ouverture a Encastrés fours pour Ouverture Max po 1/8 28 cm 71,4Montage avant vérification de Liste Une ou table une sur four le PlacezAlimentation Sécurité votre PourIncluses Pièces Requis OutilsRequis Matériel Commencer de Avant

PCT920, PCT916, PCK916, PCK920, JCTP70 specifications

The GE JCTP30, JCKS10, JCKP70, JCKP30, and JCTP70 are notable products from General Electric's diverse portfolio designed for various industrial applications. Each of these models exhibits distinct features and technologies tailored to maximize efficiency, reliability, and performance across different sectors.

Starting with the GE JCTP30, this model stands out for its compact design, making it ideal for applications with limited space. It is powered by advanced technology that ensures high throughput while maintaining energy efficiency. The JCTP30 incorporates a user-friendly interface that simplifies control and monitoring, enhancing operational ease.

The JCKS10, in contrast, is recognized for its robust construction and versatility. It is designed explicitly for harsh environments, featuring extensive protection against dust and moisture. This model supports a wide range of input/output configurations, allowing it to adapt seamlessly to various industrial processes and requirements.

Next is the GE JCKP70, which focuses on performance optimization. This unit features high-speed processing capabilities, making it suitable for time-sensitive operations. Along with its rapid operation, the JCKP70 is equipped with cutting-edge safety features, ensuring compliance with industry standards while safeguarding operators and equipment.

The JCKP30 model is tailored for applications needing precision and accuracy. With a sophisticated control system, this unit facilitates precise adjustments and monitoring, enabling operators to fine-tune processes as needed. Its integration capabilities allow it to work harmoniously with existing systems, promoting operational continuity.

Lastly, the GE JCTP70 combines high efficiency and scalability, making it a prime choice for expanding operations. This model supports modular upgrades, allowing businesses to expand their capabilities without significant overhauls. The JCTP70 also employs smart technology for real-time analytics, empowering users to make data-driven decisions to enhance productivity.

In summary, the GE JCTP30, JCKS10, JCKP70, JCKP30, and JCTP70 all showcase General Electric's commitment to innovation and excellence. Each model is equipped with a unique set of features and advanced technologies that cater to the varying demands of industrial applications. Through their combination of efficiency, reliability, and adaptability, these models help companies streamline operations and drive growth in an increasingly competitive landscape.
Top Page Image Contents