GE GE Refrigerator Location, Clearances, Remove the Fresh Food Door Handle, Back

Page 23

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

‡ 'RQRWLQVWDOOWKHUHIULJHUDWRUZKHUHWKHWHPSHUDWXUH will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.

‡ 'RQRWLQVWDOOWKHUHIULJHUDWRUZKHUHWKHWHPSHUDWXUH will go above 100°F (37°C) because it will not perform properly.

‡ ,QVWDOO LWRQDIORRUVWURQJHQRXJKWRVXSSRUWLWIXOO\ loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections.

Sides

1/8” (3 mm)

Top

1” (25 mm)

Cabinet/Hinge Cover

Back

2” (50 mm)

 

REMOVING THE REFRIGERATOR DOORS

‡IMPORTANT NOTE: This refrigerator is 361/4” deep (311/4” for CD models). Doors and passageways leading to the installation location must be at least 361/4” wide in order to leave the doors and handles attached to the refrigerator while transporting it into the installation location. If passageways are less than 361/4”, the refrigerator doors and handles can easily be scratched and damaged.

The top cap and doors can be removed to allow the refrigerator to be safely moved indoors. If passageways are less than 311/4”, start with Step 1.

‡,ILWLVQRWQHFHVVDU\WRUHPRYHGRRUVVNLSWR6WHS

11.Leave tape and all packaging on doors until the refrigerator is in the final location.

‡NOTE: Use a padded hand truck to move this refrigerator. Place the refrigerator on the hand truck with a side against the truck. We strongly recommend that TWO PEOPLE move and complete this installation.

1REMOVE THE FRESH FOOD DOOR HANDLE

Handle Design varies based on models, however Installation is same.

Stainless steel and plastic handles:

Loosen the set screws with the 1/8” Allen wrench and remove the handle.

NOTE: If the handle mounting fasteners need to be tightened or removed, use a 1/4” Allen wrench.

Mounting

Fasteners

Leave film on until after installation

2REMOVE THE FREEZER DOOR HANDLE

Handle Design varies based on models, however Installation is same.

Stainless steel and plastic handles:

Loosen the set screws with the 1/8” Allen wrench and remove the handle.

NOTE: If the handle mounting fasteners need to be tightened or removed, use a 1/4” Allen wrench.

Mounting

Fasteners

Leave film on until after installation

Reinstall the handles using the same procedure as removing.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Select Models Only Safety Instructions . . . . . . . . . . . .2Preparing to Install GE Brillion Get ConnectedInstallation GEAppliances.com Connecting ElectricityProper Disposal of Your OLD Refrigerator RefrigerantsAbout the features Door ice/water filter Remove filter/bypass plug Installing the filter cartridgeDoor ice bin Drop down dairy binGFE29, GFE27, DFE29 Control Style C, External Control About the controls with temperature settingsCubed Energy SmartChanging Temp. for Control Style D Changing the Temperature for Control Style aChanging the Temperature for Control Style B Changing the Temperature for Control Style CAbout the controls features Controls Style D, Internal Controls GNE26, PWE23 Door Alarm Freezer temp controlIce maker setting Control Style C, External ControlsTo Use the Internal Water Dispenser To reinstall Dispenser TrayAbout the dispenser Important Facts About Your DispenserImportant Facts about Auto Fill About autofillTo Use Hands Free Auto Fill To Stop Auto FillRemoving the filter cartridge When to replace the filter cartridgeAbout the GE Rpwf water filter cartridge Water Filter CartridgeQuick Space Shelf About the fresh food storage optionsRearranging the Shelves Spillproof ShelvesTray open Non-Adjustable Dairy BinAdjustable Bins on the Door Non-Adjustable Bins on the DoorClimateZone About the climate zone Temperature controlled drawerTemperature Controlled Drawer To replace About the climate zone and temperature controlled drawerHow to Remove and Replace Drawer Divider To removeBasket Removal Non-Adjustable Bin in the FreezerAbout the freezer Freezer Basket and DrawerAutomatic Ice Maker About the automatic ice makerCare and cleaning of the refrigerator Refrigerator Lights LEDs Replacing the lightsTools YOU MAY Need Before YOU BeginPreparation Overall Exterior Case Width Overall Height to Top of Hinge CoverHeight to Top of Cabinet Case Depth without Doors Remove the Fresh Food Door Handle Reinstall the handles using the same procedure as removingRefrigerator Location ClearancesInstalling the Refrigerator Reinstalling the Refrigerator Doors Replacing the Freezer Door Remove the Freezer Door600 Step Refer to 239D4144P001, Pub NoStep PasoInitial position Lift by Level the Freezer DoorRemove Packaging Tools YOU will Need AT-1MEASURE Cabinet OpeningAT-4POSITIONING the Refrigerator To the House Water Line Connecting the RefrigeratorLevel the Refrigerator See the grounding information attached to the power cordTurn on the Water Supply Plug in the RefrigeratorGE Appliances General Electric Company Louisville, KY Refrigerator Assembly Instructions, suggested assemblyRefer to 239D4129P002 Pub No Select models onlyWhat YOU will Need Installing the Water LineDrill the Hole for the Valve ‡1/2 or adjustable wrenchShut OFF the Main Water Supply Choose the Valve LocationRoute the Tubing Fasten the Shutoff ValveConnect the Tubing to the Valve Tighten the Pipe Clamp„ On models with a dispenser, during water dispense, you may Normal operating conditionsLCD models Before you call for service…SETTINGS, then Water FILTER. Select Non-LCD modelsFreezer cooling, fresh food not cooling Troubleshooting TipsAuto Fill overfills Check that the ice maker is turned on. SeeAvoid odor and taste problems ReplacementRefrigerator control panel to ensure the door alarm is on When the refrigerator is installed, or after replacThere is an adjustment to rear wheels Door removal is always required for installationAccess to final location Can be adjusted to close properlyRefer to 239D3392P001 Pub No GET ConnectedDamage caused after delivery Improper installation, delivery or maintenanceWhat GE Will Not Cover Loss of food due to spoilageRpwf Water Filter Cartridge Limited Warranty Performance Data Sheet Model GE Rpwf Water Treatment Device Certificate Number Consumer Support Schedule Service
Related manuals
Manual 48 pages 27.25 Kb Manual 3 pages 9.92 Kb

GE specifications

General Electric, commonly referred to as GE, is a global conglomerate with a diverse portfolio that encompasses several industries including aviation, healthcare, power, renewable energy, and manufacturing. Founded in 1892, GE has established itself as a leader in technology and innovation, driven by a commitment to deliver cutting-edge solutions that address the world’s most pressing challenges.

One of the hallmark features of GE is its strong emphasis on research and development. The company invests billions of dollars each year in R&D, fostering innovation across its various business sectors. This focus on technological advancement has resulted in a myriad of breakthroughs, such as GE's development of advanced jet engines that significantly improve fuel efficiency and reduce emissions, setting new standards in the aviation industry.

In healthcare, GE has revolutionized medical imaging and diagnostic technologies. With products such as MRI machines and ultrasound equipment, GE has led the way in providing high-quality imaging solutions that enhance patient care. The company’s digital healthcare technologies leverage artificial intelligence to improve diagnostics and streamline operations for healthcare providers, ultimately enhancing patient outcomes.

In the energy sector, GE is at the forefront of the shift toward renewable energy. The company develops wind turbines, gas turbines, and energy storage solutions that integrate with traditional power sources to create a more sustainable energy landscape. GE’s commitment to reducing carbon emissions is evident in its innovative technologies that harness the power of wind, solar, and hydroelectric energy.

GE’s digital industrial transformation is another defining characteristic, as it integrates the Internet of Things (IoT) into its operations and product offerings. Through the use of advanced data analytics and machine learning, GE is creating smart and connected solutions that enhance operational efficiency and predictive maintenance across industries.

The company's global presence and commitment to sustainability also contribute to its reputation as a responsible corporate citizen. GE has implemented initiatives to reduce its environmental footprint and improve community engagement around the world.

In summary, General Electric’s main features include its strong focus on R&D, revolutionary healthcare technologies, leadership in renewable energy, digital industrial transformation, and a commitment to sustainability. With a rich history and a forward-looking approach, GE continues to shape industries and improve lives through innovation.
Top Page Image Contents