GE L0523252 Installation, Instructions, Prepare HOT Water Line, Istep 11CHECK Door Balance

Page 5

Installation

PREPARE HOT WATER LINE

•The line may enter from either side, rear or floor within the shaded area shown in Figure E

•The line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2" dia. hole to accommodate the water line.

If power cord with plug is used, water line must not pass through power cord hole.

\

I .,

I \

I \

From

Cabinet

3" FromFloor

Cabinet Face

Figure F

Water Line Connection

•Turn off the water supply.

•Install a hand shut-off valve in an accessible location, such as under the sink. (Optional, but strongly recom- mended and may be required by local codes.)

•Water connection is on the left side of the dishwasher.

Install the hot water inlet line, using no less than 3/8"

O.D. copper tubing. Route the line as shown in Figure F and extend forward at least 18"from rear wall.

•Adjust water heater for 120°Fto 150°F temperature.

•Flush water line to clean out debris.

•The hotwater supply line pressure must be 20-120 PSI.

Instructions

BEFORE YOU BEGIN

Locate and set aside the package containing 2 Phillips head countertop mounting screws and 2 additional toekick screws (located in the literature package).

ISTEP 11CHECK DOOR BALANCE

To check the door balance, hold the top of the dish- washer firmly.

FigureG

•Open the door slowly, if the door drops when released, increase spring tension. If the door closes when released, decrease tension.

•Pull the spring adjustment pin out of the holes, insert in the next highest or lowest hole and test again.

•Adjust both door springs to the same tension.

•Continue moving the spring pin until door is balanced.

CAUTION:

Opening the door will cause the dishwasher to tip forward. Do not open the door until you are ready

to install the dishwasher. If it is

necessary to open the door, hold the top of the dishwasher securely with one hand and hold the door with the other hand.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Read and observe all Cautions and Warnings Read Carefully Keep These InstructionsParts Supplied Installation PreparationMaterials YOU will Need Tools YOU will NeedDrain Requirements Prepare Dishwasher EnclosureBeEvenwith Plumbingand ElectricSenlice RoomFloor. Must EnterShadedAreaPrepare Electrical Wiring To install the dishwasher. If it is InstallationInstructions Prepare HOT Water LineAdjust Leveling Legs Installation InstructionsInstall Power Cord Install 90 ElbowIstep 81 Slide Dishwasher Istep 61 Position Water Line and House WiringPartially Into Cabinet Istep 71 Insert Drain Hose Through CabinetIstep 91 Position Dishwasher Under Countertop ISTEP101LEVEL DishwasherTo Cabinet Istep 111SECURE DishwasherIstep 131 Connect Drain Line Drain Line InstallationSupply Istep 141 Connect PowerPRE-TEST Checklist Literature Istep 161 Dishwasher WET TestReplace Toekick

L0523252 specifications

The GE L0523252 is a cutting-edge product designed for efficiency and reliability in various applications. It stands out in the market due to its innovative features and advanced technologies, making it a top choice for professionals and industries alike.

One of the most notable characteristics of the GE L0523252 is its robust design. Built with high-quality materials, it ensures durability and longevity, even in challenging environments. This reliability is further enhanced by the stringent quality control measures that GE implements during manufacturing, allowing users to trust the performance of their product under different conditions.

The GE L0523252 integrates advanced technologies that contribute to its overall performance. One such feature is its optimized power management system, which maximizes energy efficiency while minimizing waste. This not only helps reduce operational costs but also aligns with global sustainability efforts by lowering the carbon footprint associated with its use.

In terms of functionality, the GE L0523252 offers a versatile range of applications. It is designed for seamless integration into existing systems, making it ideal for industries such as manufacturing, energy, and automation. Its adaptability ensures that it meets the diverse needs of various sectors, from small enterprises to large-scale operations.

Another key aspect of the GE L0523252 is its user-friendly interface. With intuitive controls and easy setup procedures, users can quickly familiarize themselves with the system. This focus on ease of use enhances productivity by reducing downtime and the need for extensive training.

Safety is a paramount concern in any industrial application, and the GE L0523252 addresses this with built-in safety features. These include overcurrent protections and thermal management systems, which safeguard the equipment from potentially damaging conditions. This commitment to safety enhances the overall value of the product in the eyes of consumers.

Furthermore, the GE L0523252 is backed by comprehensive customer support services. GE provides users with expert guidance and assistance throughout the product lifecycle, ensuring that any issues can be addressed promptly. This support network emphasizes GE's commitment to customer satisfaction and peace of mind.

In conclusion, the GE L0523252 is a product characterized by its durability, efficiency, and versatility. With state-of-the-art technologies and a focus on safety, it stands as a testament to GE's dedication to innovation in the industrial sector. Whether for energy management, automation, or manufacturing, this product proves to be an exceptional choice for those seeking reliable and efficient solutions.
Top Page Image Contents