GE L0523252 Prepare Dishwasher Enclosure, Drain Requirements, RoomFloor. Must EnterShadedArea

Page 3

Installation Preparation

PREPARE DISHWASHER ENCLOSURE

•The dishwasher must be installed so that drain hose is no more than 10feet in length for proper drainage.

•The dishwasher must be fully enclosed on the top,

sides and back, and must not support any part of the enclosure.

34"to 35" Undersideof

Countertop to Floor

Square and

CLEARANCES:When installed into a corner, allow 2" min. clearance between dishwasher and adjacent cabinet, wall or other appliances. Allow 25-5/8"rain. clearance

Countertop

Dishwashert_Ii_

Max.

FloorMUST

Plumb

from the front of the dishwasher for door opening. Figure B

_5/8"

beEvenwith Plumbingand ElectricSenlice

FigureA

RoomFloor. Must EnterShadedArea

•The rough cabinet opening must be at least 24" deep and 17-5/8" to 18"wide. The opening should be 34"to 35" max. height.

DRAIN REQUIREMENTS

•Follow local codes and ordinances.

•Do not exceed 10 feet distance to drain.

•Do not connect drain lines from other devices to the dishwasher drain hose.

•Dishwasher must be connected to waste line with an air gap (not supplied) or 32" minimum high drain loop,

depending on local codes and ordinances to prevent back flow into the dishwasher.

•Air gap must be used if waste tee or disposer connec- tion is less than 18" above the floor to prevent siphoning.

DRAIN PREPARATION

The type of drain installation depends on answers to the following questions:

Do local codes or ordinances require an air gap?

Will waste tee or disposer connection be less than 18" above the floor?

Will installation have a drain loop less than 32" above floor?

If the answer to ANY of the 3 questions above is YES, Method 1 MUST be used. Otherwise either Method 1

or Method 2 may be used. Figure C or Figure D.

CAUTION:

An air gap MUST BE USED if the drain hose is connected to waste tee or disposer lower than 18" above the floor.

Failure to provide the proper drain connection height with air gap or 32" minimum, high drain loop will result in improper draining of the dishwasher.

Opening2" Minimum

FigureB

Note: ADA installation, (32-1/2")beneath 34"high counter- tops may be accomplished by adjusting the toekick and leveling legs.

Method 1 - Air Gap with Waste Tee or Disposer

-_-re__re

FigureC

Method 2 - High Drain with Waste Tee or Disposer Provide a method to attach drain hose to underside of countertop.

FigureD

Install waste tee or disposer and air gap according to manufacturer's instructions.

CABINET PREPARATION

•Drill a 1-1/2" dia. hole in the cabinet wall within the shaded areas shown in Figure Afor the drain hose connection. The hole should be smooth with no sharp edges.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Read and observe all Cautions and Warnings Read Carefully Keep These InstructionsTools YOU will Need Installation PreparationParts Supplied Materials YOU will NeedRoomFloor. Must EnterShadedArea Prepare Dishwasher EnclosureDrain Requirements BeEvenwith Plumbingand ElectricSenlicePrepare Electrical Wiring Prepare HOT Water Line InstallationTo install the dishwasher. If it is InstructionsInstall 90 Elbow Installation InstructionsAdjust Leveling Legs Install Power CordIstep 71 Insert Drain Hose Through Cabinet Istep 61 Position Water Line and House WiringIstep 81 Slide Dishwasher Partially Into CabinetIstep 91 Position Dishwasher Under Countertop ISTEP101LEVEL DishwasherTo Cabinet Istep 111SECURE DishwasherIstep 131 Connect Drain Line Drain Line InstallationIstep 141 Connect Power PRE-TEST ChecklistSupply Istep 161 Dishwasher WET Test Replace ToekickLiterature

L0523252 specifications

The GE L0523252 is a cutting-edge product designed for efficiency and reliability in various applications. It stands out in the market due to its innovative features and advanced technologies, making it a top choice for professionals and industries alike.

One of the most notable characteristics of the GE L0523252 is its robust design. Built with high-quality materials, it ensures durability and longevity, even in challenging environments. This reliability is further enhanced by the stringent quality control measures that GE implements during manufacturing, allowing users to trust the performance of their product under different conditions.

The GE L0523252 integrates advanced technologies that contribute to its overall performance. One such feature is its optimized power management system, which maximizes energy efficiency while minimizing waste. This not only helps reduce operational costs but also aligns with global sustainability efforts by lowering the carbon footprint associated with its use.

In terms of functionality, the GE L0523252 offers a versatile range of applications. It is designed for seamless integration into existing systems, making it ideal for industries such as manufacturing, energy, and automation. Its adaptability ensures that it meets the diverse needs of various sectors, from small enterprises to large-scale operations.

Another key aspect of the GE L0523252 is its user-friendly interface. With intuitive controls and easy setup procedures, users can quickly familiarize themselves with the system. This focus on ease of use enhances productivity by reducing downtime and the need for extensive training.

Safety is a paramount concern in any industrial application, and the GE L0523252 addresses this with built-in safety features. These include overcurrent protections and thermal management systems, which safeguard the equipment from potentially damaging conditions. This commitment to safety enhances the overall value of the product in the eyes of consumers.

Furthermore, the GE L0523252 is backed by comprehensive customer support services. GE provides users with expert guidance and assistance throughout the product lifecycle, ensuring that any issues can be addressed promptly. This support network emphasizes GE's commitment to customer satisfaction and peace of mind.

In conclusion, the GE L0523252 is a product characterized by its durability, efficiency, and versatility. With state-of-the-art technologies and a focus on safety, it stands as a testament to GE's dedication to innovation in the industrial sector. Whether for energy management, automation, or manufacturing, this product proves to be an exceptional choice for those seeking reliable and efficient solutions.
Top Page Image Contents