Troubleshooting Tips, Surface Units, Drip Pans

ge.com

Be sure the controls are turned to OFF and the surface units are cool before attempting to remove them.

Safety

Surface unit

Drip pan

Surface Units

To clean the surface units, turn the control to the highest setting for a minute. The coils will burn off any soil.

To remove a surface unit:

To replace a surface unit:

Replace the drip pan into the recess in the cooktop. Make sure the opening in the pan lines up with the receptacle.

Instructions

Locking tab	Cooktop
	rim

When properly seated, the locking tab should lock onto the cooktop rim through the notch in the drip pan.

To remove the drip pans for cleaning, the surface units must be removed first.

Push the surface unit back toward the receptacle to free the locking tab from the cooktop.

Surface unit

Locking

tab

Drip pan

Receptacle

Lift the surface unit about 1 inch above the drip pan and pull it out.

Do not lift the surface unit more than 1 inch. If you do, it may not lie flat on the drip pan when you plug it back in.

NOTE: Repeated lifting of the surface unit more than 1 inch above the drip pan can permanently damage the receptacle.

Insert the terminals of the surface unit through the opening in the drip pan and into the receptacle.

Locking tab

Push the surface unit in and down to lock the tab in place so it rests evenly in the cooktop.

Do not immerse the surface units in liquids of any kind.

Do not clean the surface units in a dishwasher.

Do not bend the surface unit plug terminals.

Do not attempt to clean, adjust or in any way repair the plug-in receptacle.

Operating Instructions Care and Cleaning

Drip Pans

Remove the surface units. Then lift out the drip pans.

For best results, clean the drip pans by hand. Place them in a covered container (or a plastic bag) with 1⁄4 cup ammonia to loosen the soil. Rinse with clean water and polish with a clean soft cloth.

The drip pans may also be cleaned in a dishwasher.

Clean the area under the drip pans often. Built-up soil, especially grease, may catch fire.

Do not cover the drip pans with foil. Using foil so close to the receptacle could cause shock, fire or damage to the range.

NOTE: If your cooktop is equipped with shiny, silver-colored drip pans, do not clean them in the self-cleaning oven. Permanent damage to the finish can occur.

If your cooktop is equipped with black or gray porcelain-coated drip pans, they can be cleaned in the oven during the self-cleaning cycle. Before you begin a self-cleaning cycle, remove any heavy soil from the drip pans and place them on the porcelain-coated oven shelves. Do not place the drip pans directly on the oven bottom. After the self-cleaning cycle is completed and the drip pans are cool, wipe them with a damp cloth to remove any remaining ash or residue.

Troubleshooting Tips

Be sure all surface units are turned off before raising the cooktop.

Lift-Up Cooktop

The entire cooktop may be lifted up and supported in the up position for easier cleaning.

The surface units do not need to be removed; however, you may remove one to make raising the cooktop easier. There are two side supports that lock into position when the cooktop is lifted up.

After cleaning under the cooktop with hot, mild soapy water and a clean cloth, lower the cooktop. Be careful not to pinch your fingers.

To lower the cooktop, push the rods back and gently lower the cooktop until it rests in place.

Consumer Support

WB48X10056, WB48X10057 specifications

The GE WB48X10057 and WB48X10056 are popular replacement oven range parts, specifically designed for GE ovens. These components are widely recognized for their reliability and high performance, which are essential in the kitchen environment. Both models play a crucial role in maintaining the efficiency of various electric and gas range systems.

The WB48X10057 is a bake element, typically located at the bottom of the oven. Its primary function is to generate heat for baking. This model is crafted from durable metal materials that are designed to withstand high temperatures while ensuring even heat distribution throughout the oven. With a power rating that allows for quick heating, it significantly reduces the baking time and enhances the cooking experience. This element is also straightforward to install, requiring minimal tools, which makes it a favorite among DIY enthusiasts and professional technicians alike.

On the other hand, the WB48X10056 is the oven broil element, which is situated at the top of the oven. This component is designed for broiling and browning foods effectively, providing a high-heat source. Its design allows for intense, direct heating, which is perfect for achieving a golden brown finish on meats, casseroles, and more. Like the bake element, the broil element is made from robust materials that can handle the heat and stress of cooking environments.

Both models are equipped with safety features that prevent overheating and ensure longevity. They are characterized by their compatibility with various GE oven models, making them versatile choices for users looking to replace worn-out parts. These elements are easy to find due to their widespread use, and they come with detailed installation instructions to assist users in the replacement process.

In terms of technology, these elements utilize advanced resistance heating technology, which allows for efficient energy consumption and minimizes electricity use while maximizing cooking performance. Their design incorporates features that promote energy efficiency, which not only lowers utility bills but also supports environmentally friendly practices.

In conclusion, the GE WB48X10057 and WB48X10056 are essential components for maintaining the functionality and performance of GE ovens. With their robust construction, ease of installation, and safety features, these oven elements are a reliable choice for anyone looking to enhance their cooking experience.