GE 197D7188P001, 49-60451 operating instructions Reverse Door Swing

Page 11
Install Covers

Installation Instructions

2REVERSE DOOR SWING

SKIP THIS STEP IF DOOR SWING SUITS THE INSTALLATION

Parts Included:

•Top left case hinge

•Bottom left case hinge

•Left and right side decorative hinge cover

•Decorative hinge screw hole cover

•Torx® driver bit

Tools Required:

•Phillips screwdriver

•Electric drill

To remove the door:

•Flatten the shipping carton to use as a pad.

•Remove the 2 screws and the toekick. Set aside the screws and toekick for final installation.

•Use the supplied Torx® bit and electric drill to remove

the 3 screws holding the top case hinge. Lift off the hinge. (Screws will be used to install the new hinge.)

•Lift the door off the bottom case hinge.

•Remove the bottom case hinge pin and bracket.

To reinstall the door:

1.Remove the door stop and cam riser on the bottom right side of the door.

2.Remove the bottom fill plug on the bottom left side of the door.

3.Reinstall the original door stop and cam riser onto the bottom left side of the door.

4.Reinstall the bottom fill plug on the bottom right side of the door.

5.Remove the top fill plug on the top left side of the door.

6.Reinstall the top fill plug on the top right side.

7.Install the new supplied bottom case hinge pin and bracket onto bottom left side. Ensure plastic cam riser is on the case hinge pin.

8.Place the door onto the bottom case hinge.

9.Install the supplied left-hand top case hinge with the 3 original screws.

10.Select the hinge cover marked with an “L”.

11.Peel backing off the tape inside the decorative hinge cover.

12. Press and snap the hinge cover into place.

13. Snap the screw hole cover into place on the opposite side.

IMPORTANT: Check to be sure screws are tight and that the door is straight

and does not sag. The door should swing freely.

Install

3 Hinge

Screws

Remove

Top Hinge

Hinge

Pin and

Bracket

Door Stop

and Cam Riser

Remove

Hinge

Install Toekick

The toekick has a cutout on the left and right sides.

1. Remove the

 

 

plug on the

 

Move Fill

left side and

 

 

Plug to

reinstall on

Spacer

Right Side

the right side.

 

Standoff

 

 

 

2. Install original

screws and spacers.

Install screws through the spacer standoff, toekick and into the base as shown.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Chiller Tips Consumer Support Care and CleaningOperating Instructions Instructions TroubleshootingConsumer Controls and features-Beverage CenterCareand Cleaning Installation Instructions Tips SupportInserting Wine Bottles Controls and features-Wine ChillerRemoving Full Extension Drawers Controls and features-Beverage Center and Wine ChillerSafety Interior Light and SwitchInstructions Operating Care and cleaningChoose the location When installed in a cornerProduct Clearances Read these instructions completely and carefullyCutout depth should be 24″ Installation SpaceSIDE-BY-SIDE Installations Additional SpecificationsStaining Wood Drawer Fronts Tools RequiredParts Supplied Grounding the Wine Chiller and Beverage CenterReverse Door Swing Slide Product Into the Cutout Connect PowerSET Temperature Controls LevelFans come on in order to cool the appliance Care and CleaningNormal operating sounds Installation Instructions Before you call for service…Safety Instructions Operating Care and Cleaning Operating Instructions Safety Instructions Troubleshooting TipsGeneral Electric Company GE Service Protection PlusConsumer Product Ownership Registration What GE Will Not Cover Wine Chiller or Beverage Center WarrantyInstructions Installation GE Will ReplaceReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances WebsiteRefrigerador Centro de No almacene o instale este aparato en el exterior RefrigerantesAntes de desechar su antiguo refrigerador Guarde Estas Instrucciones Estantes de cristal Controles y funciones Centro de bebidasInstalación Cuidado y limpieza Control de temperaturaInserción de botellas de vino Controles y funciones Refrigerador de vinoPara quitar los cajones Cuidado y limpiezaQuitar los cajones de extensión completa Luz interior e interruptorCuidado y limpieza Elija la ubicación Tolerancias DEL ProductoLea estas instrucciones en su totalidad y con atención Cuando se instale en una esquinaLa profundidad de sección debe ser de 610 mm 24″ EL Espacio DE InstalaciónInstalaciones Conjuntas CorteDestornillador Philips número Llave inglesa Herramientas NecesariasPartes Suministradas Quitar EL EmbalajeInvertir EL Sentido DE Apertura DE LA Puerta Definir Controles DE Temperatura NivelarConectar LA Alimentación Deslizar EL Producto Hacia EL HuecoWhoosh Sonidos de funcionamiento normalesCuidado y Antes de llamar para solicitar servicio técnico…Limpieza Operación Se crea humedad en Notas Seguridad Operación Notas Partes defectuosas Garantía del refrigerador de vino o centro de bebidasPor el período de GE reemplazará Lo que GE no cubriráPiezas y accesorios Soporte al consumidor Página Web de GE AppliancesSolicite una reparación Garantías ampliadas

197D7188P001, 49-60451 specifications

The GE 49-60451, also known as 197D7188P001, is a vital component within the domain of gas turbine technology, primarily utilized in the aerospace industry. Designed to optimize engine performance and enhance reliability, this model represents the cutting-edge advancements in aircraft propulsion systems.

One of the key features of the GE 49-60451 is its superior materials engineering. It incorporates high-temperature alloys and advanced composite materials that withstand the extreme conditions encountered during flight. This ensures durability and longevity, enabling the turbine to operate efficiently over extended periods, while resisting thermal fatigue and corrosion.

The technology behind the GE 49-60451 revolves around innovative aerodynamics. The design utilizes advanced computational fluid dynamics (CFD) simulations, allowing for the optimization of airflow through the turbine stages. This results in improved thrust-to-weight ratios and enhanced fuel efficiency, which are critical factors in modern aviation where cost-effectiveness is paramount.

Another notable characteristic of the GE 49-60451 is its modular design. This allows for easier maintenance and faster turnaround times in aircraft servicing. The modular approach not only facilitates efficient diagnostics and repairs but also aids in the rapid replacement of components, reducing downtime and enhancing operational availability.

Additionally, the integration of digital technologies is a significant aspect of the GE 49-60451. With the advent of the Internet of Things (IoT), this model is equipped with advanced sensors that monitor various operational parameters in real time. This data is vital for predictive maintenance, enabling operators to preemptively address issues before they escalate, thereby ensuring safer and more reliable flights.

The GE 49-60451 also adheres to stringent environmental standards. Its design emphasizes reduced emissions and lower noise levels, aligning with global initiatives to make aviation more sustainable. The combination of these features contributes to less environmental impact, meeting the needs of modern regulatory frameworks.

In conclusion, the GE 49-60451, or 197D7188P001, stands out for its exceptional engineering, cutting-edge technology, and commitment to sustainability. Its high-performance capabilities make it an indispensable component in the future of aviation propulsion systems, ensuring that operators benefit from both efficiency and reliability while minimizing their environmental footprint.
Top Page Image Contents