GE 49-60451, 197D7188P001 Controls and features-Beverage Center, Careand Cleaning, Consumer

Page 4

Instructions

Controls and features—Beverage Center.

Temperature Control

Safety

 

 

Operating

Instructions

The operating temperatures of the beverage center range from the low forties to the mid fifties.

Do not install the beverage center where the temperature will go below 55°F (13°C) or above 90°F (32°C).

As with any refrigeration product, there is a slight temperature variance at different locations within the cabinet.

The coolest area will be in the lower part of the cabinet.

The cooler area will be in the middle section.

The upper part of the cabinet is the warmest section.

When the temperature is adjusted, allow 24 hours for the unit to stabilize.

To set the control, turn it to the midpoint setting (approximately 45ºF). Once the beverage center is loaded, allow at least 24 hours before making any adjustments to the initial setting.

Careand Cleaning

To remove, lift up on the back of the shelf

Glass Shelves

Tempered glass shelves in the beverage center unit are removable for easy cleaning or for storing larger items.

To remove a shelf, open the door completely to avoid potential damage to the gasket. Lift up on the back of the shelf slightly. Tilt the shelf to one side at an angle while pulling forward.

Installation

Instructions

 

 

Tips

Support

Troubleshooting

To replace a shelf, open the door completely to avoid potential damage to the gasket. Tilt the shelf to one side at an angle and slide toward the back wall, placing one side onto the shelf support. Place the other side onto the opposite shelf support. Ensure rear locking tabs are engaged. When installed properly, the shelf will not slide forward when gently pulled.

Tilt the shelf at an angle while removing or replacing

Place in slots when replacing the shelf

Consumer

Loading Tips and Suggestions

• The bottom two full extension drawers hold

 

six bottles each and are loaded with necks

 

facing the rear. Tall bottles should not be

 

loaded on the bottom drawer because

Bottom drawer arrangement

they may prevent the door from closing.

 

•Do not allow children to climb, stand or hang on the beverage center shelves or full extension drawers. They could seriously injure themselves and possibly cause damage to the beverage center.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Chiller Operating Instructions Care and CleaningTips Consumer Support Troubleshooting InstructionsControls and features-Beverage Center Careand CleaningInstallation Instructions Tips Support ConsumerControls and features-Wine Chiller Inserting Wine BottlesControls and features-Beverage Center and Wine Chiller SafetyInterior Light and Switch Removing Full Extension DrawersCare and cleaning Instructions OperatingWhen installed in a corner Product ClearancesRead these instructions completely and carefully Choose the locationInstallation Space SIDE-BY-SIDE InstallationsAdditional Specifications Cutout depth should be 24″Tools Required Parts SuppliedGrounding the Wine Chiller and Beverage Center Staining Wood Drawer FrontsReverse Door Swing Connect Power SET Temperature ControlsLevel Slide Product Into the CutoutNormal operating sounds Care and CleaningFans come on in order to cool the appliance Safety Instructions Before you call for service…Installation Instructions Operating Troubleshooting Tips Care and Cleaning Operating Instructions Safety InstructionsGE Service Protection Plus General Electric CompanyConsumer Product Ownership Registration Wine Chiller or Beverage Center Warranty Instructions InstallationGE Will Replace What GE Will Not CoverSchedule Service Parts and AccessoriesConsumer Support GE Appliances Website Real Life Design StudioRefrigerador Centro de Antes de desechar su antiguo refrigerador RefrigerantesNo almacene o instale este aparato en el exterior Guarde Estas Instrucciones Controles y funciones Centro de bebidas Instalación Cuidado y limpiezaControl de temperatura Estantes de cristalControles y funciones Refrigerador de vino Inserción de botellas de vinoCuidado y limpieza Quitar los cajones de extensión completaLuz interior e interruptor Para quitar los cajonesCuidado y limpieza Tolerancias DEL Producto Lea estas instrucciones en su totalidad y con atenciónCuando se instale en una esquina Elija la ubicaciónEL Espacio DE Instalación Instalaciones ConjuntasCorte La profundidad de sección debe ser de 610 mm 24″Herramientas Necesarias Partes SuministradasQuitar EL Embalaje Destornillador Philips número Llave inglesaInvertir EL Sentido DE Apertura DE LA Puerta Nivelar Conectar LA AlimentaciónDeslizar EL Producto Hacia EL Hueco Definir Controles DE TemperaturaSonidos de funcionamiento normales WhooshLimpieza Operación Antes de llamar para solicitar servicio técnico…Cuidado y Se crea humedad en Notas Seguridad Operación Notas Garantía del refrigerador de vino o centro de bebidas Por el período de GE reemplazaráLo que GE no cubrirá Partes defectuosasSoporte al consumidor Página Web de GE Appliances Solicite una reparaciónGarantías ampliadas Piezas y accesorios

197D7188P001, 49-60451 specifications

The GE 49-60451, also known as 197D7188P001, is a vital component within the domain of gas turbine technology, primarily utilized in the aerospace industry. Designed to optimize engine performance and enhance reliability, this model represents the cutting-edge advancements in aircraft propulsion systems.

One of the key features of the GE 49-60451 is its superior materials engineering. It incorporates high-temperature alloys and advanced composite materials that withstand the extreme conditions encountered during flight. This ensures durability and longevity, enabling the turbine to operate efficiently over extended periods, while resisting thermal fatigue and corrosion.

The technology behind the GE 49-60451 revolves around innovative aerodynamics. The design utilizes advanced computational fluid dynamics (CFD) simulations, allowing for the optimization of airflow through the turbine stages. This results in improved thrust-to-weight ratios and enhanced fuel efficiency, which are critical factors in modern aviation where cost-effectiveness is paramount.

Another notable characteristic of the GE 49-60451 is its modular design. This allows for easier maintenance and faster turnaround times in aircraft servicing. The modular approach not only facilitates efficient diagnostics and repairs but also aids in the rapid replacement of components, reducing downtime and enhancing operational availability.

Additionally, the integration of digital technologies is a significant aspect of the GE 49-60451. With the advent of the Internet of Things (IoT), this model is equipped with advanced sensors that monitor various operational parameters in real time. This data is vital for predictive maintenance, enabling operators to preemptively address issues before they escalate, thereby ensuring safer and more reliable flights.

The GE 49-60451 also adheres to stringent environmental standards. Its design emphasizes reduced emissions and lower noise levels, aligning with global initiatives to make aviation more sustainable. The combination of these features contributes to less environmental impact, meeting the needs of modern regulatory frameworks.

In conclusion, the GE 49-60451, or 197D7188P001, stands out for its exceptional engineering, cutting-edge technology, and commitment to sustainability. Its high-performance capabilities make it an indispensable component in the future of aviation propulsion systems, ensuring that operators benefit from both efficiency and reliability while minimizing their environmental footprint.
Top Page Image Contents