GE 197D7188P001, 49-60451 operating instructions Troubleshooting, Instructions

Page 3

ge.com

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

If you have only a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

NOTE: GFI (ground fault interrupter) is not recommended.

The appliance should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your appliance by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the appliance away from the wall, be careful not to roll over or damage the power cord.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

3

Instructions

Operating

Care and Cleaning

 

 

Instructions

Installation

 

 

Troubleshooting

Consumer Support

Tips

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Chiller Care and Cleaning Operating InstructionsTips Consumer Support Instructions TroubleshootingConsumer Controls and features-Beverage CenterCareand Cleaning Installation Instructions Tips SupportInserting Wine Bottles Controls and features-Wine ChillerRemoving Full Extension Drawers Controls and features-Beverage Center and Wine ChillerSafety Interior Light and SwitchInstructions Operating Care and cleaningChoose the location When installed in a cornerProduct Clearances Read these instructions completely and carefullyCutout depth should be 24″ Installation SpaceSIDE-BY-SIDE Installations Additional SpecificationsStaining Wood Drawer Fronts Tools RequiredParts Supplied Grounding the Wine Chiller and Beverage CenterReverse Door Swing Slide Product Into the Cutout Connect PowerSET Temperature Controls LevelCare and Cleaning Normal operating soundsFans come on in order to cool the appliance Before you call for service… Safety InstructionsInstallation Instructions Operating Care and Cleaning Operating Instructions Safety Instructions Troubleshooting TipsGeneral Electric Company GE Service Protection PlusConsumer Product Ownership Registration What GE Will Not Cover Wine Chiller or Beverage Center WarrantyInstructions Installation GE Will ReplaceReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances WebsiteRefrigerador Centro de Refrigerantes Antes de desechar su antiguo refrigeradorNo almacene o instale este aparato en el exterior Guarde Estas Instrucciones Estantes de cristal Controles y funciones Centro de bebidasInstalación Cuidado y limpieza Control de temperaturaInserción de botellas de vino Controles y funciones Refrigerador de vinoPara quitar los cajones Cuidado y limpiezaQuitar los cajones de extensión completa Luz interior e interruptorCuidado y limpieza Elija la ubicación Tolerancias DEL ProductoLea estas instrucciones en su totalidad y con atención Cuando se instale en una esquinaLa profundidad de sección debe ser de 610 mm 24″ EL Espacio DE InstalaciónInstalaciones Conjuntas CorteDestornillador Philips número Llave inglesa Herramientas NecesariasPartes Suministradas Quitar EL EmbalajeInvertir EL Sentido DE Apertura DE LA Puerta Definir Controles DE Temperatura NivelarConectar LA Alimentación Deslizar EL Producto Hacia EL HuecoWhoosh Sonidos de funcionamiento normalesAntes de llamar para solicitar servicio técnico… Limpieza OperaciónCuidado y Se crea humedad en Notas Seguridad Operación Notas Partes defectuosas Garantía del refrigerador de vino o centro de bebidasPor el período de GE reemplazará Lo que GE no cubriráPiezas y accesorios Soporte al consumidor Página Web de GE AppliancesSolicite una reparación Garantías ampliadas

197D7188P001, 49-60451 specifications

The GE 49-60451, also known as 197D7188P001, is a vital component within the domain of gas turbine technology, primarily utilized in the aerospace industry. Designed to optimize engine performance and enhance reliability, this model represents the cutting-edge advancements in aircraft propulsion systems.

One of the key features of the GE 49-60451 is its superior materials engineering. It incorporates high-temperature alloys and advanced composite materials that withstand the extreme conditions encountered during flight. This ensures durability and longevity, enabling the turbine to operate efficiently over extended periods, while resisting thermal fatigue and corrosion.

The technology behind the GE 49-60451 revolves around innovative aerodynamics. The design utilizes advanced computational fluid dynamics (CFD) simulations, allowing for the optimization of airflow through the turbine stages. This results in improved thrust-to-weight ratios and enhanced fuel efficiency, which are critical factors in modern aviation where cost-effectiveness is paramount.

Another notable characteristic of the GE 49-60451 is its modular design. This allows for easier maintenance and faster turnaround times in aircraft servicing. The modular approach not only facilitates efficient diagnostics and repairs but also aids in the rapid replacement of components, reducing downtime and enhancing operational availability.

Additionally, the integration of digital technologies is a significant aspect of the GE 49-60451. With the advent of the Internet of Things (IoT), this model is equipped with advanced sensors that monitor various operational parameters in real time. This data is vital for predictive maintenance, enabling operators to preemptively address issues before they escalate, thereby ensuring safer and more reliable flights.

The GE 49-60451 also adheres to stringent environmental standards. Its design emphasizes reduced emissions and lower noise levels, aligning with global initiatives to make aviation more sustainable. The combination of these features contributes to less environmental impact, meeting the needs of modern regulatory frameworks.

In conclusion, the GE 49-60451, or 197D7188P001, stands out for its exceptional engineering, cutting-edge technology, and commitment to sustainability. Its high-performance capabilities make it an indispensable component in the future of aviation propulsion systems, ensuring that operators benefit from both efficiency and reliability while minimizing their environmental footprint.
Top Page Image Contents