Peavey 10P manual Specifications DU

Page 41

SPECIFICATIONS DU

Peavey PR10P

Enclosure: Peavey PR 10P (domestic)

Frequency response: 67 Hz to 20 kHz

Low frequency limit (-3 dB point): 67 Hz

Useable low frequency limit (-10 dB point):

55 Hz

Internal power amplifiers (@120 VAC line):

Woofer - 200 Watts peak dynamic power

150 Watts @ less than 0.1% distortion Tweeter - 70 Watts peak dynamic power 50 Watts @ less than 0.1% distortion.

Nominal sensitivity (1W @1M, swept sine input in anechoic environment): 95 dB

Maximum sound pressure level: 119 dB music peak

Nominal radiation angles: 90˚ horizontal by 40˚ vertical

Transducer complement:

10" heavy duty woofer and RX14 1.4" titanium diaphragm compression driver tweeter

Box tuning frequency (Fbox): 76 Hz

Electroacoustic crossover frequency: 2,200 Hz

Crossover type:

Internal Electronic two-way crossover with CD horn EQ, level matching, bass boost and subsonic filtering.

Crossover Slopes:

18 dB/octave (third order) low pass,

18 dB/octave (third order) high pass, both with staggered poles and driver EQ. Unit has horn spatially aligned with woofer, so there is no need for phase alignment or time delay of the signals.

Electronic Input Impedance (Nominal): 10 k Ohms unbalanced, 20 k Ohms balanced line level, 2.4 k Ohms balanced mic level.

Input Connections:

One combo female XLR/ 1/4" phone jack providing balanced operation, with switch selectable mic or line level sensitivity. Also has two 1/4" phone jack line level unbalanced inputs with a concentric pair of level controls.

Enclosure materials and finish: Injection-molded polypropylene of a nominal thickness of 1/4" with internal ribbing and bracing, and with textured finish. Molded material is dark gray

Mounting:

Subwoofer pole-mounting via molded- in mount, flying via Versamount35 (top or bottom of cabinet) or the newer Versamount70 (with extra mounting holes in the Versamount35 pattern), and 4 rubber feet for floor use.

Dimensions:

18.88" (47.9 cm) tall {17.63" /44.8 cm in rear} by 14.00" (35.6 cm) wide {8.25"/21.0 cm in rear} by 13.13"

(33.3 cm) deep

Optional accessories: Impulse® 100 Floor Monitor Kit (FG# 00454130)

Net weight: 37 lbs.

Additional remarks:

Also available as a passively crossed- over unit, the Peavey PR10.

ELECTRONICS AND AMPLIFIER SPECIFICATIONS:

Electronic input impedance (nominal): Primary balanced input: 20 k Ohms line level sensitivity selected, 2.4 k Ohms mic level sensitivity selected, 10 k Ohms unbalanced 1/4."

Mic switch sensitivity Increase: 30 dB

Infrasonic filter protection: 36 dB/octave roll-off

Nominal amplifier frequency response: +0, -1 dB from 10 Hz to 30 kHz

Hum and noise:

Greater than 90 dB below rated power

DDT dynamic range:

Greater than 14 dB

THD and IM:

Typically less than 0.1 %

Damping factor:

Greater than 100 @ 1000 Hz, 8 Ohms

Power requirements of Peavey PR12P system (domestic):

Nominal 100 Watts, 120 VAC, 60 Hz

41

Image 41
Contents Page Page Sound Level dBA, Slow Response Important Safety InstructionsDescription FeaturesON-OFF Switch IEC Power Cord ConnectionApplications A R P a N E LO N T P a N E L Flying the PR 10P E R a T I N G I N S T R U C T I O N SSpecial Note for Permanent Installation Getting AC Power To The PR10PGetting a Signal to the PR 10P Volume Control AdjustmentMixing Signals Using the Volume Knobs Mic/Line Pad AdjustmentTroubleshooting No Output at AllCleaning Care and MaintenanceHum or Buzz Distorted or Fuzzy SoundCheck for Secure Hardware Architectural and Engineering SpecificationsTouchup Peavey PR10P Frequency Response Curves Beschreibung MerkmaleC K E N V E R T I E F T E S EinsatzbereicheSicherung Anschluss DES IEC-NETZKABELSSecondary INPUTS, Channel 2 und POWER/CLIP-LEDConcentric VOLUME, Channel 2 und Fliegen des PR 10P T R I E B S a N L E I T U N GSenden von Signalen an den PR 10P Besondere Hinweise für die DauerinstallationVersorgung des PR10P mit Wechselstrom Einsatz des PR 10P mit einem SubwooferEinstellen des Mic/Line-Schalters Mischen von Signalen über die LautstärkereglerEinstellen des Lautstärkereglers Keine Ausgangsleistung FehlersucheBrummen oder Summen Verzerrter oder verschwommener SoundSonnenlicht bzw. Hitze Pflege und WartungReinigung Pflege der OberflächeBauliche und technische Spezifikationen Spezifikationen Descripción CaracterísticasN E L T R a S E R O AplicacionesFusible Conexión Para Cable DE Corriente IECN E L F R O N T a L Volando EL PR 10P S T R U C C I O N E S D E O P E R a C I Ó NGetting AC Power To The PR10P Troubleshooting Distorted or Fuzzy Sound Check for Secure Hardware Especificaciones Caractéristiques Interrupteur ON-OFF N N E a U a R R I E R EConnecteur IEC N N E a U a V a N T Concentric Volume Controle DE Volume DES Canaux 2Primary Input Entree Canal Secondary Inputs Entree Canaux 2Suspendre la PR 10P N U E L D ’ U T I L I S a T I O NPage Trouver L’ORIGINE DE Problemes Courants Page Page Specifications DU Page Product Category Peavey Electronics Corporation Limited Warranty80304966