Peavey 10P manual O N T P a N E L

Page 6

F R O N T P A N E L

5

6

7

4

8

9

(4) POWER/CLIP LED

Illuminates GREEN when the electronics receive power (when the Power switch (3) is On). Illuminates RED when amplifier clipping is occurring or the unit has tripped the thermal protection system.

(5) PRIMARY INPUT (CHANNEL 1)

The primary input is switchable between line-level and mic-level input. The line-level input is of the medium impedance balanced type, and when switched to mic-level it is of a typical low-Z mic input impedance. Jack (5) is a combo female XLR and 1/4" TRS connector.

(6) PAD

Switches the sensitivity of Channel 1 from line-level to mic-level sensitivity. Pushed all the way in, the sensitivity is set for line-level input signals, and when the white tab is closer to the front panel, the sensitivity is increased by 30 dB so it is suitable for mic-level signals.

(7) VOLUME

Controls the gain (level) of the Primary Input (5), Channel 1, of the powered speaker system. It is used to directly set the system output level for the Channel 1 input signal.

(8) SECONDARY INPUTS, CHANNEL 2 & 3

These consist of 1/4" unbalanced phone jacks for line-level signals, with medium input impedance.

(9) CONCENTRIC VOLUME, CHANNEL 2 & 3

Controls the gain (level) of Channel 2 & 3 inputs. Can be used in conjunction with the Channel 1 volume control (7) to mix three line-level signals together, or two line-level signals and one mic-level signal.

6

Image 6

Contents Page Page Important Safety Instructions Sound Level dBA, Slow ResponseFeatures DescriptionApplications IEC Power Cord ConnectionON-OFF Switch A R P a N E LO N T P a N E L E R a T I N G I N S T R U C T I O N S Flying the PR 10PGetting a Signal to the PR 10P Getting AC Power To The PR10PSpecial Note for Permanent Installation Volume Control AdjustmentTroubleshooting Mic/Line Pad AdjustmentMixing Signals Using the Volume Knobs No Output at AllHum or Buzz Care and MaintenanceCleaning Distorted or Fuzzy SoundArchitectural and Engineering Specifications TouchupCheck for Secure Hardware Peavey PR10P Frequency Response Curves Merkmale BeschreibungSicherung EinsatzbereicheC K E N V E R T I E F T E S Anschluss DES IEC-NETZKABELSPOWER/CLIP-LED Concentric VOLUME, Channel 2 undSecondary INPUTS, Channel 2 und T R I E B S a N L E I T U N G Fliegen des PR 10PVersorgung des PR10P mit Wechselstrom Besondere Hinweise für die DauerinstallationSenden von Signalen an den PR 10P Einsatz des PR 10P mit einem SubwooferMischen von Signalen über die Lautstärkeregler Einstellen des LautstärkereglersEinstellen des Mic/Line-Schalters Brummen oder Summen FehlersucheKeine Ausgangsleistung Verzerrter oder verschwommener SoundReinigung Pflege und WartungSonnenlicht bzw. Hitze Pflege der OberflächeBauliche und technische Spezifikationen Spezifikationen Características DescripciónFusible AplicacionesN E L T R a S E R O Conexión Para Cable DE Corriente IECN E L F R O N T a L S T R U C C I O N E S D E O P E R a C I Ó N Volando EL PR 10PGetting AC Power To The PR10P Troubleshooting Distorted or Fuzzy Sound Check for Secure Hardware Especificaciones Caractéristiques N N E a U a R R I E R E Connecteur IECInterrupteur ON-OFF Primary Input Entree Canal Concentric Volume Controle DE Volume DES Canaux 2N N E a U a V a N T Secondary Inputs Entree Canaux 2N U E L D ’ U T I L I S a T I O N Suspendre la PR 10PPage Trouver L’ORIGINE DE Problemes Courants Page Page Specifications DU Page Peavey Electronics Corporation Limited Warranty Product Category80304966