Peavey 10P manual Applications, A R P a N E L, Fuse, IEC Power Cord Connection, ON-OFF Switch

Page 5

Applications

The Peavey PR10P has a variety of applications such as sound reinforcement, public address, side fill system, karaoke or musical playback. With the optional monitor stand kit, the Peavey PR 10P makes an excellent stage monitor.

A typical signal source for the line-level inputs of the Peavey PR 10P would be a sound reinforcement mixing console (mixer) or the output from a CD player, Minidisc player or tape deck. A dynamic microphone can be connected and used as well.

R E A R P A N E L

2

1

3

(1) FUSE

The unit is AC power line fuse protected from overloads and fault conditions with an ABC-type fast-blow 5 Amp fuse. This fuse is located within the cap of the fuse holder. If the fuse fails, THE FUSE MUST BE REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT AND TO PREVENT VOIDING THE WARRANTY. If the unit repeatedly blows fuses, it should be taken to a qualified service center for repair.

(2) IEC POWER CORD CONNECTION

This receptacle is for the IEC line cord (supplied) that provides AC power to the unit.

Never break off the ground pin on any equipment. It is provided for your safety. If the outlet used does not have a ground pin, a suitable grounding adapter should be used and the third wire should be grounded properly. To prevent the risk of shock or fire hazard, always be sure that the mixer and all other associated equipment are properly grounded.

(3) ON-OFF SWITCH

This rocker switch supplies AC power to the PR 10P when switched to the ON position.

5

Image 5
Contents Page Page Sound Level dBA, Slow Response Important Safety InstructionsDescription FeaturesON-OFF Switch IEC Power Cord ConnectionApplications A R P a N E LO N T P a N E L Flying the PR 10P E R a T I N G I N S T R U C T I O N SSpecial Note for Permanent Installation Getting AC Power To The PR10PGetting a Signal to the PR 10P Volume Control AdjustmentMixing Signals Using the Volume Knobs Mic/Line Pad AdjustmentTroubleshooting No Output at AllCleaning Care and MaintenanceHum or Buzz Distorted or Fuzzy SoundCheck for Secure Hardware Architectural and Engineering SpecificationsTouchup Peavey PR10P Frequency Response Curves Beschreibung MerkmaleC K E N V E R T I E F T E S EinsatzbereicheSicherung Anschluss DES IEC-NETZKABELSSecondary INPUTS, Channel 2 und POWER/CLIP-LEDConcentric VOLUME, Channel 2 und Fliegen des PR 10P T R I E B S a N L E I T U N GSenden von Signalen an den PR 10P Besondere Hinweise für die DauerinstallationVersorgung des PR10P mit Wechselstrom Einsatz des PR 10P mit einem SubwooferEinstellen des Mic/Line-Schalters Mischen von Signalen über die LautstärkereglerEinstellen des Lautstärkereglers Keine Ausgangsleistung FehlersucheBrummen oder Summen Verzerrter oder verschwommener SoundSonnenlicht bzw. Hitze Pflege und WartungReinigung Pflege der OberflächeBauliche und technische Spezifikationen Spezifikationen Descripción CaracterísticasN E L T R a S E R O AplicacionesFusible Conexión Para Cable DE Corriente IECN E L F R O N T a L Volando EL PR 10P S T R U C C I O N E S D E O P E R a C I Ó NGetting AC Power To The PR10P Troubleshooting Distorted or Fuzzy Sound Check for Secure Hardware Especificaciones Caractéristiques Interrupteur ON-OFF N N E a U a R R I E R EConnecteur IEC N N E a U a V a N T Concentric Volume Controle DE Volume DES Canaux 2Primary Input Entree Canal Secondary Inputs Entree Canaux 2Suspendre la PR 10P N U E L D ’ U T I L I S a T I O NPage Trouver L’ORIGINE DE Problemes Courants Page Page Specifications DU Page Product Category Peavey Electronics Corporation Limited Warranty80304966