Each Compartment has capacity for:
• Five, 12˝ x 20˝ x1⁄˝2 deep Cafeteria Pans.
WATER QUALITY
REQUIREMENTS
The quality of water varies greatly from region to region. Steam equipment generators must be drained daily and chemically descaled periodically to ensure proper operation. To minimize service problems caused by the accumulation of minerals and chemicals in water review the following quality guidelines with a local water treatment specialist. Inlet water that is beyond these specified guidelines should be treated to achieve these acceptable limits. Total Dissolved Solids less than 60 ppm, Alkalinity less than 20 ppm, Silica less than 13 ppm, pH factor greater than 7.5, Chlorine less than 30 ppm.
ABDEC
|
| GAS |
|
| ELECTRIC | C COLD WATER |
| CLEARANCE | D DRAINAGE |
| |
| 1 ⁄4˝ IPS line size,⁄4˝ (13mm) connection | 35 psi minimum |
|
|
| 1 ⁄2˝ dia. |
| ||||
|
| RIGHT = 3˝ operating, |
| ||||||||
| 1 | 3 |
|
|
|
|
| Right - 3”, Left - 3”, |
| 1 |
|
|
|
|
|
|
|
|
| Rear |
|
|
|
| NATURAL | PROPANE | BTU | 2 Blowers & Controls | 60 psi maximum |
| 12˝ if adjoining wall or |
| Do not connect other |
| |
|
|
|
|
|
|
|
| (12” on control side if adjoining |
|
|
|
| Piping 3⁄4˝ N.P.T. | Piping3⁄4˝ N.P.T. |
|
|
|
|
|
| |||
| 72,000 each | 150 watts each |
|
| wall or equipmentLEFT =is over3˝ 30” |
| units to this drain |
| |||
| Supply pressure | Supply pressure | Generator, |
| One (E) 1/4" dia. |
| high for service access) |
|
|
| |
|
|
| REAR = 3˝ |
|
|
| |||||
| 4.50˝ W.C. Min. | 11.00˝ W.C. Min. | 144,000 total |
| NPT for Generator |
| Allow 6˝ space min. |
| Drain must be vented |
| |
|
|
|
|
|
|
|
| Contact factory |
|
|
|
| 14.00˝ W.C. Max. | 14.00˝ W.C. Max. |
|
|
|
|
| for variances to |
|
|
|
|
|
|
|
|
| from rear and sides |
|
|
| ||
|
|
|
|
|
| One (D) 1/4" dia |
| clearances. |
| Do not use PVC pipe |
|
|
|
|
|
|
|
| when located near |
|
| ||
| Manufacturer must be notified if unit will |
|
|
| NPT for Condenser |
| combustible walls |
|
|
| |
| be used above 2,000 feet |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NOTES:
Cleveland Range reserves right of design improvement or modification, as warranted.
Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes.
Cleveland Range equipment is built to comply with applicable standards for manufacturers. Included among those approval agencies are UL/NSF#4 and CSA (AGA, CGA).
(NOT TO SCALE) SECT. IV PAGE 14 0402
Litho in U.S.A.