Liebherr 20707 Fitting the unit doors, For a 23-5/8 600 mm wide recess, For chipboard doors

Installation

u Slightly		loosen			the
screws Fig. 20 (55).
u Secure		the			top
mounting			bracket
Fig. 20 (50) to the unit
wall	with		a	ø4x19
chipboard				screw
Fig. 20 (29).						Fig. 20
u Break off the protruding
end	of	the			cover
Fig. 20 (53).
u Tighten the screws Fig. 20 (55) .
u Place the cover Fig. 20 (53) in position.
On the handle side at the bottom:
u Slightly		loosen			the
screws Fig. 21 (51).
u Secure		the			bottom
mounting				bracket
Fig. 21 (50) to the unit wall
with a ø4x19 chipboard
screw Fig. 21 (29) .
u Break off the protruding
end	of	the			cover
Fig. 21 (53).					screws
u Tighten		the				Fig. 21
Fig. 21 (51)		.			cover
u Place		the
Fig.21 (54) into position on
the	bottom		mounting
bracket Fig. 21 (50).

u Slide the equalizer trim Fig.12 (20) toward the handle side as far as it will go.

u Close the appliance door.

6.2 Fitting the unit doors

Fig. 22

The fitting aids Fig. 22 (30) are required for both doors.

You must therefore fit the unit doors one after the other.

u Verify the 5/16 '' (8 mm) presetting. (Distance between appliance door and lower edge of crosspiece)

u Raise the fitting aids Fig. 22 (30) to the unit door height. Bottom stop edge ▲ of fitting aid = top edge of unit door to be fitted.

u Unscrew				the
crosspiece				by
Fig. 23		(31)
undoing				the
locknuts Fig.23 (32).
u Hang				the
crosspiece			on the
Fig. 23 (31)
inside	of	the		unit
door	using			the				Fig. 23
fitting				aids
Fig. 23 (30).
For a 23-5/8 '' (600 mm) wide recess:
u To center the crosspiece Fig. 23 (31): Mark a short center
line on the unit door and place the tip of the arrow on the
crosspiece over it.
w Distances to the outer edges are the same to the right
and to the left.
For a 24 '' (609.6 mm) wide recess:
u To align the crosspiece Fig. 23 (31): Mark a short center
line on the unit door and place the tip of the arrow on the
crosspiece			over it.		Now	shift	the	crosspiece
Fig. 23 (31)3/16 in. (5.5 mm) towards the hinge side.
For chipboard doors:
u Fasten the crosspiece Fig. 23 (31) with at least 6 screws
Fig. 23 (41).
For frame and panel doors:						23 (31)	with	4 screws
u Fasten	the		crosspiece		Fig.
Fig. 23 (41) at the edge.

u Lift up the fitting aids Fig. 23 (30), turn them around, and insert them into the adjacent openings.

Fig. 24 u Attach the unit door on the adjusting bolts Fig. 24 (33) and

loosely screw the locknuts Fig. 24 (32) onto the adjusting bolts.

u Close the door.

u Check the gap between the door and the surrounding unit doors.

u To laterally align the unit door: Move the unit door in the X direction.

u To align the unit door in height and in lateral inclination: Adjust the adjusting bolts Fig. 24 (33) with a screwdriver. w The unit door is flush and in alignment with the

surrounding unit fronts.

u Tighten the locknuts Fig. 24 (32).

11