Liebherr 7084284-03 Defrosting with NoFrost, Cleaning the appliance, Cleaning the IceMaker

Page 15

Maintenance

u Pay attention that the defrost water does not run into the kitchen unit.

u If necessary, pick up defrost water several times, using a sponge or cloth.

u Clean the appliance (see 6.3) and rub dry.

6.2 Defrosting with NoFrost*

The NoFrost system automatically defrosts the appliance.

Refrigerator compartment:

The defrost water evaporates due to the compressor heat. Drops of water on the rear wall are perfectly normal.

u Regularly clean the drain opening to allow the water to flow away (see 6.3) .

Freezer compartment:

The moisture condenses on the evaporator, is periodically defrosted and evaporates.

u The appliance does not have to be manually defrosted.

6.3 Cleaning the appliance

CAUTION

Risk of injury and damage as a result of hot steam! Hot steam may damage the surfaces and cause burns. u Do not use any steam cleaners!

NOTICE

Incorrect cleaning damages the appliance!

u Do not use cleaning agents in concentrated form.

u Do not use any scouring or abrasive sponges or steel wool. u Please do not use any aggressive, scouring, sand-,

chloride-, chemical- or acid-based cleaning agents. u Do not use chemical solvents.

u Do not damage or remove the type plate on the inside of the appliance. It is important for the customer service.

u Do not pull off, bend or damage cables or other compo- nents.

u Do not allow any cleaning water to enter the drain channel, ventilation grille or electrical parts.

u Please use soft cleaning cloths and a universal pH-neutral cleaning agent.

u Please use cleaning and care products suitable for contact with foodstuffs in the appliance interior.

u Empty appliance.

u Pull out the power plug.

u Clean plastic outer and inner surfaces with lukewarm water and a little washing-up liquid.

u Clean drain hole: Remove deposits with a narrow instrument, e.g. a cotton bud.

u Clean items of equipment by hand with lukewarm water and a little washing-up liquid.

u Remove the support rails for the half glass shelves for cleaning.

u To dismantle the shelves: remove trims and side parts.

*

u To dismantle door racks: Pull off protective film from the decorative trims.*

u Dismantle door racks as illus- trated.*

*

After cleaning:

u Wipe dry the appliance and items of equipment. u Connect the appliance and switch it on again. u Switch on SuperFrost (see 5.6.4) .

When the temperature is sufficiently cold: u Put the food back inside.

6.4 Cleaning the IceMaker*

Fig. 30

The IceMaker has to be switched on.

u Pull out the drawer and remove the ice cubes.

u Clean the drawer with warm water and mild washing-up liquid.

u When the drawer is pulled out, hold down the On/Off button (about 10 seconds).

w After about 1 s the LED goes out, the IceMaker is switched off.

w After about 10 s the LED flashes for about 60 s. u Slide in the drawer while the LED is flashing.

w The ice-cube tray of the IceMaker turns to a skew position. u Remove the drawer.

u Clean the ice cube tray with warm water. If necessary, use mild washing-up liquid. Then rinse.

Switch the IceMaker on again.

u Press the ON/OFF button until the LED shines, then slide in the drawer.

w The IceMaker starts producing ice cubes. If washing-up liquid was used:

u throw away the first three loads of ice cubes to get rid of any remaining washing-up liquid.

6.5 Replacing the interior light*

Bulb data q max. 25 W

q Bulb fitting: E14

q Current type and voltage must conform with the data on the type plate

uSwitch off the appliance.

uPull out the mains plug or switch off/unscrew the fuse.

uTake hold of the lamp cover at the top and bottom Fig. 31 (1).

uDisengage the lamp cover at the back and detach it Fig. 31 (2).

uReplace the bulb Fig. 31 (3).

Apply slight pressure when turning the bulb to overcome the friction of the seal. Pay attention that the seal is seated properly in the lamp socket.

Fig. 31

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operating and installation instructions Contents Appliance at a glanceAppliance at a glance Saving energy General safety informationGeneral safety information ConformityControls and displays Controls and displaysPutting into operation To change the hinges Putting into operationChanging the door hinges To detach the soft stop mechanismWater connection InstallationAll appliances Installing the applianceFitting the unit doors For large unit doors For 600 mm-wide recessFor particle board doors For frame and panel doorsControl ControlDoor alarm Temperature alarmRefrigerator compartment Freezer compartment Shelves Setting the temperature in the freezer compartmentSuperFrost DrawersIceMaker MaintenanceMaintenance Manual defrostingReplacing the interior light Cleaning the applianceCleaning the IceMaker Defrosting with NoFrostCustomer service MalfunctionMalfunction Decommissioning Switching off the applianceTaking the appliance out of service DecommissioningDisposing of the appliance

7084284-03 specifications

The Liebherr 7084284-03 is a high-quality component designed for use in various applications, particularly in the construction and material handling sectors. Known for its reliability and efficiency, this part reflects Liebherr's commitment to robust engineering and innovation.

One of the core features of the Liebherr 7084284-03 is its durability, constructed from premium materials that withstand the rigors of demanding environments. This makes it ideal for heavy-duty applications, whether used in cranes, excavators, or other machinery. The resilience of this component ensures a longer service life, reducing downtime and maintenance costs.

In terms of technology, the Liebherr 7084284-03 integrates advanced mechanical systems designed to enhance operational efficiency. It employs cutting-edge design techniques that optimize performance while minimizing wear and tear. This precision engineering contributes to the smooth operation of machinery, ensuring that tasks are completed efficiently and safely.

The component is also designed with ease of installation and maintenance in mind. Its user-friendly design allows for quick replacements or repairs, which is critical in environments where time is of the essence. Maintenance becomes straightforward, allowing operators to focus more on productivity rather than on equipment issues.

Another notable characteristic of the Liebherr 7084284-03 is its compatibility with a wide range of machinery. This versatility means that it can be integrated seamlessly into existing setups, providing a cost-effective solution for those looking to enhance their equipment's capabilities without extensive modifications.

Moreover, the component is engineered to operate under various environmental conditions, including extreme temperatures and humidity levels. Its performance is tested rigorously to ensure it meets industry standards, giving operators the confidence that it will perform reliably under any conditions.

Overall, the Liebherr 7084284-03 embodies the high standards of quality and innovation that Liebherr is known for. With its impressive features, advanced technologies, and robust characteristics, it stands out as a component that enhances the reliability and efficiency of machinery in the construction and material handling industry. As businesses seek to improve their operational capabilities, components like the Liebherr 7084284-03 are invaluable assets.
Top Page Image Contents