Liebherr 7084284-03 installation instructions Controls and displays, Putting into operation

Page 4

Controls and displays

3 Controls and displays

3.1 Operating and control elements

Fig. 2

(8) Child-proofing symbol

(1)

Alarm button

(2)

SuperFrost button

(9) Down setting button,

(3)

On/Off button, freezer

refrigerator compartment

(10) Up setting button, refriger-

(4)

compartment

ator compartment

Down setting button,

(11) On/Off button, refrigerator

(5)

freezer compartment

compartment

Up setting button,

(12) SuperCool button

(6)

freezer compartment

(13) Fan button*

Freezer compartment

(7)

temperature display

 

Refrigerator compart-

 

 

ment temperature

 

 

display

 

3.2 Temperature display

The following are displayed in normal operation:

-the warmest freezing temperature

-the average cooling temperature

The freezer compartment temperature display flashes:

-the temperature setting is being changed

-after switch-on the temperature is not yet cold enough

-the temperature has risen several degrees

Dashes flash in the display:

-the freezer temperature is above 0 °C.

The following displays indicate malfunction. Possible causes and corrective action (see Malfunction).

-nA

-F0 to F5

4 Putting into operation

4.1 Transporting the appliance

CAUTION

Risk of injury and danger of damage as a result of incorrect transport!

u Transport the appliance in a packed condition. u Transport the appliance upright.

u Do not transport the appliance without assistance.

4.2 Installing the appliance

In the event that the appliance is damaged, contact the supplier immediately before connecting to the mains.

The floor at the site must be flat and level.

Do not install the appliance in a location where it is exposed to direct radiation of the sun, next to a cooker, heater and similar. Do not install the appliance without assistance.

Standard EN 378 specifies that the room in which you install your appliance must have a volume of 1 m2 per 8 g of R 600a refrigerant used in the appliance. If the room in which the appli- ance is installed is too small, a flammable gas-air mixture may form in the event of a leakage in the refrigeration circuit. The quantity of refrigerant used in your appliance is indicated on the type plate on the inside of the appliance.

Fit the appliance in stable kitchen units only. The following ventilation gaps must be observed:

q The depth of the ventilation channel at the rear of the unit must be at least 38 mm.

q There must be a ventilation space of at least 200 cm2 in the plinth and at the top of the unit.

q Basically the principle applies: the larger the ventilation space, the more energy-saving the appliance is in operation.

WARNING

Risk of fire due to short circuit!

If the mains cable/connector of the appliance or of another appliance touch the rear of the appliance, the mains cable/ connector may be damaged by the appliance vibrations, leading to a short circuit.

u Stand the appliance so that it is not touched by connectors or main cables.

u Do not plug the appliance or any others into sockets located near the rear of the appliance.

WARNING

Fire hazard due to dampness!

If live parts or the mains lead become damp this may cause short circuits.

u The appliance is designed for use in enclosed areas. Do not operate the appliance outdoors or in areas where it is exposed to splash water or damp conditions.

u Only use the appliance when it is installed.

WARNING

Fire hazard due to refrigerant!

The refrigerant R 600a is environmentally friendly but flam- mable. Escaping refrigerant may ignite.

u Do not damage the piping of the refrigeration circuit.

WARNING

Fire hazard and danger of damage!

u Do not place appliances emitting heat e.g. microwaves, toasters etc. on the appliance!

u Detach the connecting cable from the rear of the appliance, removing the cable holder at the same time because other- wise there will be vibratory noise!

After installation:

u Remove the protective film from the decorative trims and drawer fronts.

u Remove all transit supports.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Operating and installation instructions Appliance at a glance ContentsAppliance at a glance General safety information General safety informationConformity Saving energyControls and displays Controls and displaysPutting into operation Putting into operation Changing the door hingesTo detach the soft stop mechanism To change the hingesInstallation Water connectionInstalling the appliance All appliancesFitting the unit doors For 600 mm-wide recess For particle board doorsFor frame and panel doors For large unit doorsControl ControlTemperature alarm Door alarmRefrigerator compartment Freezer compartment Setting the temperature in the freezer compartment SuperFrostDrawers ShelvesMaintenance MaintenanceManual defrosting IceMakerCleaning the appliance Cleaning the IceMakerDefrosting with NoFrost Replacing the interior lightMalfunction Customer serviceMalfunction Switching off the appliance Taking the appliance out of serviceDecommissioning DecommissioningDisposing of the appliance

7084284-03 specifications

The Liebherr 7084284-03 is a high-quality component designed for use in various applications, particularly in the construction and material handling sectors. Known for its reliability and efficiency, this part reflects Liebherr's commitment to robust engineering and innovation.

One of the core features of the Liebherr 7084284-03 is its durability, constructed from premium materials that withstand the rigors of demanding environments. This makes it ideal for heavy-duty applications, whether used in cranes, excavators, or other machinery. The resilience of this component ensures a longer service life, reducing downtime and maintenance costs.

In terms of technology, the Liebherr 7084284-03 integrates advanced mechanical systems designed to enhance operational efficiency. It employs cutting-edge design techniques that optimize performance while minimizing wear and tear. This precision engineering contributes to the smooth operation of machinery, ensuring that tasks are completed efficiently and safely.

The component is also designed with ease of installation and maintenance in mind. Its user-friendly design allows for quick replacements or repairs, which is critical in environments where time is of the essence. Maintenance becomes straightforward, allowing operators to focus more on productivity rather than on equipment issues.

Another notable characteristic of the Liebherr 7084284-03 is its compatibility with a wide range of machinery. This versatility means that it can be integrated seamlessly into existing setups, providing a cost-effective solution for those looking to enhance their equipment's capabilities without extensive modifications.

Moreover, the component is engineered to operate under various environmental conditions, including extreme temperatures and humidity levels. Its performance is tested rigorously to ensure it meets industry standards, giving operators the confidence that it will perform reliably under any conditions.

Overall, the Liebherr 7084284-03 embodies the high standards of quality and innovation that Liebherr is known for. With its impressive features, advanced technologies, and robust characteristics, it stands out as a component that enhances the reliability and efficiency of machinery in the construction and material handling industry. As businesses seek to improve their operational capabilities, components like the Liebherr 7084284-03 are invaluable assets.
Top Page Image Contents