Liebherr 7084284-03 installation instructions Maintenance, Manual defrosting, IceMaker

Page 14

Maintenance

Using cold storage accumulators*

u Freeze and store the cold storage accumu- lators in the ceiling of the freezer compart- ment (appliances without No-Frost module).

With the top drawer removed:

u to insert cold storage accu-

mulators: slide cold storage accumulator into the top back of the freezer compartment ceiling and snap into place at the front.

With the top drawer removed:

u to remove cold storage accumulators: take hold of the cold storage accumu- lator at the side and press it down for removal.

Using cold storage accumulators*

uPlace the cold storage accumula- tors in the top freezer compart- ment to save space.

uPlace the frozen cold storage accumulators on the frozen food in the upper front area of the freezer compartment.

5.6.10 IceMaker*

The IceMaker is in the top drawer of the freezer compartment. The drawer is marked "IceMaker".

Make certain that the following conditions are met:

-The appliance is level.

-The appliance is connected.

-The freezer compartment is switched on.

-The IceMaker is connected to the water supply.

Switching on the IceMaker*

Fig. 29

uPull out the drawer.

uPress the On/Off button Fig. 29 (1) so that the LED Fig. 29 (2) shines.

uPush in the drawer.

Note

u The IceMaker produces ice cubes only if the drawer is fully closed.

Producing ice cubes*

The production capacity depends on the freezer temperature. The lower the temperature, the more ice cubes can be produced in a specific period.

The ice cubes drop from the IceMaker into the drawer. When a certain filling level has been reached, no further ice cubes are produced. The IceMaker does not fill the drawer right up to the brim.

If large quantities of ice cubes are needed, the complete IceMaker drawer can be exchanged for the adjacent drawer. When the drawer is closed, the IceMaker automatically re- commences production.

Once the IceMaker has been switched on for the first time, it may take up to 24 hours until the first ice cubes are produced.

Note

When the appliance is used for the first time and if it has been out of use for a long time, particles may collect in the IceMaker and/or water conduit.

u Therefore do not use or consume the ice cubes made in the first 24 hours.

Switching off the IceMaker*

If no ice cubes are needed, the IceMaker can be switched off independently of the freezer compartment.

When the IceMaker is switched off, the IceMaker drawer can also be used for freezing and storing food.

u Press the On/Off button for about 1 second until the LED goes out.

u Clean the IceMaker.

w This ensures that no water or ice remains in the IceMaker.

6 Maintenance

6.1 Manual defrosting*

The refrigerator compartment is defrosted automatically. The defrost water evaporates as a result of the heat of the compressor. Drops of water on the rear wall are perfectly normal.

u Regularly clean the drain opening to allow the water to flow away (see 6.3) .

A layer of frost or ice can build up in the freezer compartment after a long period of operation.

The layer of frost or ice builds up faster if the appliance is opened often or if the food is warm when placed inside. However, a thick layer of ice will increase the appliance‘s energy consumption. You should therefore defrost the appli- ance regularly.

CAUTION

Risk of injury and damage as a result of hot steam!

u Do not use electric heaters or steam cleaners, naked flames or defrosting sprays for defrosting.

u Do not remove ice using sharp instruments.

u Switch on SuperFrost one day before defrosting.

w The frozen goods are provided with a "cold reserve". u Switch off the appliance.

w The temperature display goes out.

w If the temperature display does not go out, the child lock function (see 5.2) is active.

u Pull out the power plug or switch off the fuse.

u Place cold storage accumulators on top of the frozen food. u If possible, put the frozen goods in the freezer drawer,

wrapped in newspaper or a blanket, and store in a cool place.

u Place a pan with hot, not boiling water on a middle shelf.

-or-

u Half-fill the two lower drawers with lukewarm water and put them in the appliance.

w Defrosting is speeded up.

w Defrost water is collected in the drawers.

u Leave the door of the appliance open while defrosting. u Remove detached pieces of ice.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operating and installation instructions Appliance at a glance ContentsAppliance at a glance Conformity General safety informationGeneral safety information Saving energyPutting into operation Controls and displaysControls and displays To detach the soft stop mechanism Putting into operationChanging the door hinges To change the hingesInstallation Water connectionInstalling the appliance All appliancesFitting the unit doors For frame and panel doors For 600 mm-wide recessFor particle board doors For large unit doorsControl ControlRefrigerator compartment Door alarmTemperature alarm Freezer compartment Drawers Setting the temperature in the freezer compartmentSuperFrost ShelvesManual defrosting MaintenanceMaintenance IceMakerDefrosting with NoFrost Cleaning the applianceCleaning the IceMaker Replacing the interior lightMalfunction Customer serviceMalfunction Decommissioning Switching off the applianceTaking the appliance out of service DecommissioningDisposing of the appliance

7084284-03 specifications

The Liebherr 7084284-03 is a high-quality component designed for use in various applications, particularly in the construction and material handling sectors. Known for its reliability and efficiency, this part reflects Liebherr's commitment to robust engineering and innovation.

One of the core features of the Liebherr 7084284-03 is its durability, constructed from premium materials that withstand the rigors of demanding environments. This makes it ideal for heavy-duty applications, whether used in cranes, excavators, or other machinery. The resilience of this component ensures a longer service life, reducing downtime and maintenance costs.

In terms of technology, the Liebherr 7084284-03 integrates advanced mechanical systems designed to enhance operational efficiency. It employs cutting-edge design techniques that optimize performance while minimizing wear and tear. This precision engineering contributes to the smooth operation of machinery, ensuring that tasks are completed efficiently and safely.

The component is also designed with ease of installation and maintenance in mind. Its user-friendly design allows for quick replacements or repairs, which is critical in environments where time is of the essence. Maintenance becomes straightforward, allowing operators to focus more on productivity rather than on equipment issues.

Another notable characteristic of the Liebherr 7084284-03 is its compatibility with a wide range of machinery. This versatility means that it can be integrated seamlessly into existing setups, providing a cost-effective solution for those looking to enhance their equipment's capabilities without extensive modifications.

Moreover, the component is engineered to operate under various environmental conditions, including extreme temperatures and humidity levels. Its performance is tested rigorously to ensure it meets industry standards, giving operators the confidence that it will perform reliably under any conditions.

Overall, the Liebherr 7084284-03 embodies the high standards of quality and innovation that Liebherr is known for. With its impressive features, advanced technologies, and robust characteristics, it stands out as a component that enhances the reliability and efficiency of machinery in the construction and material handling industry. As businesses seek to improve their operational capabilities, components like the Liebherr 7084284-03 are invaluable assets.
Top Page Image Contents