Control
uDetach the connecting cable from the rear of the appliance, removing the cable holder at the same time because other- wise there will be vibratory noise!
After installation:
u Remove the protective film from the decorative trims and drawer fronts.
u Remove all transit supports.
u Dispose of packaging material (see 4.6) .
NOTICE
Risk of damage due to condensate!
If your appliance is not a
u do not install the appliance directly alongside a further refrig- erator/freezer.
u Always see to good ventilation at the installation site.
4.6 Disposing of packaging
WARNING
Danger of suffocation due to packing material and plastic film! u Do not allow children to play with packing material.
The packaging is made of recyclable materials:
-corrugated board/cardboard
-EPS moulded parts
-polythene bags and sheets
-polypropylene straps
uTake the packaging material to an official collecting point.
4.7 Connecting the appliance
NOTICE
Risk of damage to the electronic control system!
u Do not use
WARNING
Fire and overheating hazard!
u Do not use extension cables or multiple socket outlets.
The type of current (alternating current) and voltage at the instal- lation site have to conform with the data on the type plate (see Appliance at a glance).
Connect the appliance only with a properly installed socket outlet with earthing contact. The socket outlet must be fused with 10 A or higher.
uCheck the electrical connection.
uClean the appliance (see 6.3) .
uPlug in the power plug.
4.8 Switching on the appliance
Note
u To switch on the entire appliance it is necessary only to switch on the freezer compartment.
Put the appliance into operation about 2 hours before first loading food to be frozen.
Do not load food to be frozen before the temperature display reads
4.8.1 Switching on the freezer compartment
u Press On/Off button, freezer compartment Fig. 2 (3).
w The refrigerator compartment temperature display shows the set temperature.
wThe freezer compartment temperature display and the alarm button flash until the temperature is sufficiently cold. If the temperature is above 0 °C, dashes flash. If it is below, the current temperature flashes.
4.8.2Switching on refrigerator and BioFresh compartment
uPress On/Off button, refrigerator compartment Fig. 2 (11). w The interior light is on when the door is open.
w The temperature displays shine. Refrigerator and BioFresh compartment and freezer compartment are switched on.
5 Control
5.1 Saving energy
uAlways pay attention to good ventilation.
uKeep the time the appliance is open to a minimum.
uStore food logically.
uFirst cool warm food to room temperature before storing it .
uDefrost frozen food in the refrigerator.
5.2Brightness of the temperature dis- play
You can adjust the brightness of the temperature display to the light conditions of the room in which the appliance is installed.
5.2.1 Adjusting the brightness
The brightness is adjustable between h1 (no illumination) and h5 (maximum luminosity).
u To activate the setting mode: press the SuperFrost button Fig. 2 (2) for about 5 s.
w The display indicates c.
w The SuperFrost button flashes.
u Using the Up setting button, freezer compartment Fig. 2 (5) or Down setting button, freezer compartment Fig. 2 (4), select h.
u To confirm: briefly press the SuperFrost button Fig. 2 (2).
u To make the display brighter: press Up button, freezer compartment Fig. 2 (5).
u To make the display darker: press Down button, freezer compartment Fig. 2 (4).
u To confirm: press SuperFrost button Fig. 2 (2). w The brightness is adjusted to the new value.
u To deactivate the
u Wait for 5 minutes.
wThe temperature is indicated again in the temperature display.
5.3 Child proofing
The
5.3.1 Setting the child lock
u To activate the setting mode: press SuperFrost button Fig. 2 (2) for about 5 s.
w The display indicates c.
w The button SuperFrost flashes.
u Briefly press the SuperFrost button Fig. 2 (2) to confirm. u To switch on: Using the Up setting button, freezer
compartment Fig. 2 (5) or Down setting button, freezer compartment Fig. 2 (4), select c1.
10