Liebherr 110309 7084282 - 01 Fitting the unit doors, For 600 mm-wide recess

Page 8

Putting into operation

u Vertically align the appliance by means of the adjustable- height feet Fig. 8 (25), using the accompanying open-ended spanner Fig. 8 (26).

w The appliance is now correctly positioned in depth. The dis- tance from the front edge of the side wall of the unit to the appliance body is 42 mmall the way round. (Allow for door stop components, such as knobs and sealing lips.)

Note

Incorrect installation will lead to malfunction!

If the distance is not kept, the door may not close. This may lead to icing, to condensate forming and to malfunction.

u Be sure to keep to the clearance of 42 mm all the way round. (Allow for door stop components, such as knobs and sealing lips.)

Tightly screw the appliance into place in the recess: u At the top and bottom of

both doors with Spax screws Fig. 17 (28) passed through the hinge plates.

On the handle side at the top:

Fig. 17

 

u Loosen

the

screws

 

 

Fig. 18 (55) a little.

 

u Tightly

screw

the top

 

 

mounting

bracket

 

 

Fig. 18 (50) to the unit wall

 

 

using

Spax

screw

 

 

Fig. 18 (29) ø4x19.

 

u Break off the projecting

 

 

end

of the

cover

Fig. 18

 

Fig. 18 (53).

 

u Tighten the screws Fig. 18 (55).

 

u Put on the cover Fig. 18 (53).

 

On the handle side at the bottom:

 

u Loosen

the

screws

 

 

Fig. 19 (51) a little.

 

u Tightly screw the bottom

 

 

mounting

bracket

 

 

Fig. 19 (50) to the unit wall

 

 

using

Spax

screw

 

 

Fig. 19 (29) ø4x19.

 

u Break off the projecting end

 

 

of the cover Fig. 19 (53). It

 

 

is no longer required.

 

u Tighten

the

screws

 

 

Fig. 19 (51).

 

Fig. 19

u

Put the cover Fig.19 (54) on

the bottom mounting brack- et Fig. 19 (50).

u Close the appliance door.

4.3.2 Fitting the unit doors

Fig. 20 The fitting aids Fig.20 (30) are required for both doors. There- fore fit the unit doors one after the other.

uCheck 8 mm-presetting. (Distance between appliance door and lower edge of crosspiece)

uSlide up the assembly aids Fig.20 (30) to the height of the unit door. Lower stop edge ▲of the assembly aid = upper edge of the unit door to be fitted.

uUnscrew the cross- piece Fig. 21 (31) by undoing the locknuts Fig. 21 (32).

uAttach the cross- piece Fig. 21 (31) to- gether with the as-

sembly aids Fig. 21 (30) to the in- side of the unit door.

Fig. 21

For 600 mm-wide recess:

u Concentrically align the crosspiece Fig. 21 (31): Mark a short centre line on the unit door and put the tip of the arrow on the crosspiece over it.

w Distances to the outer edge are equal at the left and right.

For particle board doors:

u Tightly screw the crosspiece Fig. 21 (31) into place using at least 6 screws Fig. 21 (41).

For frame and panel doors:

u Tightly screw the crosspiece Fig. 21 (31) into place using 4 screws Fig. 21 (41) at the edge.

u Raise and remove the assembly aids Fig. 21 (30), turn them and slide them into the adjacent openings.

Fig. 22 u Attach the unit door to the adjusting bolts Fig. 22 (33) and loosely screw the locknuts Fig. 22 (32) onto the adjusting

bolts.

u Close the door.

u Check the gap between the door and the surrounding unit doors.

u To laterally align the unit door: Move the unit door in the X direction.

u Align unit door in height and lateral inclination: Adjust the ad- justing bolts Fig. 22 (33) using a screwdriver.

w The unit door is flush and in alignment with the surrounding unit fronts.

u Tighten the lock nuts Fig. 22 (32). Ensure that both metal

edges are flush (sym- bol //):

u Drill pilot holes in the door of the unit (possi- bly make preliminary hole with a bradawl).

Fig. 23 u Screw the appliance door to the unit door with screws Fig. 23 (41) passed through the mounting brackets

Fig. 23 (34).

8

Image 8
Contents Operating and installation instructions Appliance at a glance ContentsAppliance at a glance Description of appliance and equip- ment Net@Home General safety informationGeneral safety information Putting into operation Controls and displaysControls and displays Installation Putting into operationWater connection To change the hingesSicbn Installing the appliance All appliancesFor 16 mm-thick unit walls = Slide in and align the applianceFitting the unit doors For 600 mm-wide recessFor particle board doors For frame and panel doorsFor large unit doors Installing the applianceTransporting the appliance Control ControlRefrigerator compartment Door alarmTemperature alarm BioFresh compartment Setting the humidity in the HydroSafe Freezer compartmentDrawers Thawing foodSetting the temperature in the freezer com- partment SuperFrostShelves VarioSpaceMaintenance MaintenanceManual defrosting Cold storage accumulatorsCleaning the appliance Cleaning the IceMakerCustomer service Defrosting with NoFrostMalfunction MalfunctionSwitching off the appliance Taking the appliance out of serviceDecommissioning Decommissioning