Rev.0008
HUSSMANN CHINO PRODUCT CONTROL
The serial number and shipping date of all equipment has been recorded in Hussmann’s files for warranty and re- placement part purposes. All correspondence pertaining to warranty or parts ordering must include the serial num- ber of each piece of equipment involved, in order to pro- vide the customer with the correct parts.
The Hussmann warranty is printed on the back
of this guide.
Cut & Plan Views
Product temperature should always be maintained at a constant and proper temperature. This means that from the time the product is received, through storage, prepa- ration and display, the temperature of the product must be controlled to maximize life of the product.
UNCRATING THE STAND
Place the fixture as close to its permanent position as possible. Remove the top of the crate. Detach the walls from each other and remove from the skid. Unbolt the case from the skid. The fixture can now be lifted off the crate skid. Lift only at base of stand!
EXTERIOR LOADING
| Light |
| Ref. Dome |
| (Optional) |
End |
|
Panel | Coil |
8" | |
12" |
|
19 1/2" | Condensing |
| Unit |
| S.C. |
| Elec. |
" | Access |
| |
*12 | " |
| *5 |
12" | 30" | 8 1/4" |
|
|
|
48"
13"
97/8"
*36"
Adj. Wire
Racks
These models have not been structurally designed to sup- port excessive external loading. Do not walk on their tops; This could cause serious personal injury and dam- age to the fixture.
AVOID REMOVING CONCRETE
All cases were leveled and joined prior to shipment to ensure closest possible fit when cases are joined in the field. To avoid removing concrete flooring, begin
lineup at highest point of store floor.
LEVELING
IMPORTANT! It is imperative that the case
|
|
|
|
|
|
|
|
| RGSSFP (S.C) |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| shown with Optional Refrigerated Rear Storage |
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| In- | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
8" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
| CONDENSING |
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
| 16" | ||||||||
|
|
|
|
|
|
|
| UNIT |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
| DRAIN & ELEC. |
| REFRIG. |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| MECHANICAL |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| MECHANICAL |
|
|
| 48" | |||||||
|
|
|
|
|
|
|
|
| none |
|
| ||||||||
|
|
|
|
|
|
|
| STUB UP AREA |
| STUB UP AREA |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| 18" X 18" |
|
|
|
|
|
|
|
|
|
| |
16" |
|
|
|
|
|
|
| CASE FRONT |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1" | 8" |
|
|
|
| 1" |
|
| |||||||||||
|
|
| 8" |
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Plan View
LOCATION
The refrigerated merchandisers have been designed for use only in air conditioned stores where temperature and humidity are maintained at or below 75° F and 55% rela- tive humidity.DO NOT allow air conditioning, electric fans, open doors or windows (etc.) to create air currents around the merchandiser, as this will impair its correct operation.
be leveled from front to back and side to side prior to joining. A level case is necessary to insure proper operation.
JOINT TRIM
After the case has been leveled and joined, and refrigera- tion, electrical, and waste piping work completed, install the splashguards. Fasten along the top edge, or center, with #10 X 3/8" sheet metal screws.
DO NOT SEAL JOINT TRIM TO FLOOR!
Plumbing
WASTE OUTLET AND P-TRAP
The waste outlet is located off the center of the case on one side allowing drip piping to be run lengthwise under the fixture.
A
NOTE:
3