Maintenance
BEFORE SERVICING – Always disconnect electrical power at the main disconnect when servicing or replacing any electrical component
This includes (but not limited to) Fans, Heaters,
Thermostats, and Lights.
REPLACING FLUORESCENT LAMPS
Fluorescent lamps are furnished with a shatterproof pro- tective coating. The same type of lamp with protective coating must be used if replaced.
This lamp has been treated to resist breakage and must be replaced with a similarly treated lamp in order to maintain
compliance with NSF Standards. | NSF CODE 4.28.1 |
Contact HUSSMANN Chino for replacement | |
x 2131 |
COPPER COILS
The copper coils used in Hussmann merchandisers may be repaired in the field. Materials are available from local refrigeration wholesalers.
Hussmann recommends using #15
TIPS & TROUBLESHOOTING
Before calling for service, check the following:
1.Check electrical power supply to the equipment for connection.
2.Check fixture loading. Overstocking case will affect its proper operation.
3.If frost is collecting on fixture and/or product, check that Humidity Control is working properly, and that no outside doors or windows are
Please
EVAPORATOR FANS
The evaporator fans are located at the center front of these merchandisers directly beneath the display pans. Should fans or blades need servicing, always replace fan blades with the raised embossed side of the blade TOWARD THE MOTOR.
FOR PROMPT SERVICE
When contacting the factory,
be sure to have the Case Model and Serial Number handy. This information is on a plate located on the case itself.
Electrical and Refrigeration Specifications
Model | Refrigeration |
|
| Average |
| Disch. Air | T~Stat | Coil Type | Fan Blade |
| Defrosts | Electrical Load (Amps) @ ~115 VAC |
| Condensing Unit Data |
| ||||
& | Btu / Hr. |
| Temperatures (°F) |
| Speed | Settings | Size (in) & | Evap. | Motors | per day | Evap.Fans Case | Case | Defrost | Glass | Set (PSI) | Size | Voltage | Ampacity | |
Length | (Ft.) | (Total) | Evap. | Prod. | Disch. | (CFM) | (°F) | pitch ( ° ) | Fans | Qty | Length Qty | Fans Warmer | Lights | Heater | Heater | Out | In | (HP) | (VAC) |
SCSS-M Medium Temperature
4' | 650 | 2,600 | 20° | 40° | 30° | 200 | Optional Forced Air | 4" Axial | 2 | 30 | 2 | 0.28 | 0.35 | 0.54 |
|
| 30 | 50 | 1/2 | 115 | 13.6 |
5' | 650 | 3,250 | 20° | 40° | 30° | 200 | Optional Forced Air | 4" Axial | 2 | 30 | 2 | 0.28 | 0.43 | 0.54 |
|
| 30 | 50 | 3/4 | 115 | 18.5 |
6' | 650 | 3,900 | 20° | 40° | 30° | 200 | Optional Forced Air | 4" Axial | 3 | 30 | 2 | 0.42 | 0.52 | 0.54 |
|
| 30 | 50 | 3/4 | 115 | 18.5 |
8' | 650 | 5,200 | 20° | 40° | 30° | 200 | Optional Forced Air | 4" Axial | 4 | 30 | 2 | 0.56 | 0.70 | 0.54 |
|
| 30 | 50 | 1 | 208~230 11.8 | |
Low Temperature |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
4' | 800 | 3,200 | 200 | Optional Forced Air | 4" Axial | 2 | 20 | 1 | 0.28 | 0.35 | 0.54 | 5.77 | 0.42 | 30 | 50 | 208 | 14.7 | ||||
5' | 800 | 4,000 | 200 | Optional Forced Air | 4" Axial | 2 | 20 | 1 | 0.28 | 0.43 | 0.54 | 9.62 | 0.52 | 30 | 50 | 208 | 14.7 | ||||
6' | 800 | 4,800 | 200 | Optional Forced Air | 4" Axial | 3 | 20 | 1 | 0.42 | 0.52 | 0.54 | 9.62 | 0.63 | 30 | 50 | 208 | 14.7 | ||||
8' | 800 | 6,400 | 200 | Optional Forced Air | 4" Axial | 4 | 20 | 1 | 0.56 | 0.70 | 0.54 | 10.82 | 0.63 | 30 | 50 | 2 | 208 | 12.8 | |||
| Slim Line - Medium Temperature |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
4' | 540 | 2,160 | 20° | 40° | 30° | 200 | Optional Forced Air | 4" Axial | 2 | 30 | 2 | 0.28 | 0.35 | 0.54 |
|
| 30 | 50 | 1/2 | 115 | 13.6 |
5' | 540 | 2,700 | 20° | 40° | 30° | 200 | Optional Forced Air | 4" Axial | 2 | 30 | 2 | 0.28 | 0.43 | 0.54 |
|
| 30 | 50 | 3/4 | 115 | 18.5 |
6' | 540 | 3,240 | 20° | 40° | 30° | 200 | Optional Forced Air | 4" Axial | 3 | 30 | 2 | 0.42 | 0.52 | 0.54 |
|
| 30 | 50 | 3/4 | 115 | 18.5 |
8' | 540 | 4,320 | 20° | 40° | 30° | 200 | Optional Forced Air | 4" Axial | 4 | 30 | 2 | 0.56 | 0.70 | 0.54 |
|
| 30 | 50 | 1 | 208 ~ 23011.8 | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
4' | 625 | 2,500 | 200 | Optional Forced Air | 4" Axial | 2 | 20 | 1 | 0.28 | 0.35 | 0.54 | 5.77 | 0.42 | 30 | 50 | 208 | 14.7 | ||||
5' | 625 | 3,125 | 200 | Optional Forced Air | 4" Axial | 2 | 20 | 1 | 0.28 | 0.43 | 0.54 | 9.62 | 0.52 | 30 | 50 | 208 | 14.7 | ||||
6' | 625 | 3,750 | 200 | Optional Forced Air | 4" Axial | 3 | 20 | 1 | 0.42 | 0.52 | 0.54 | 9.62 | 0.63 | 30 | 50 | 208 | 14.7 | ||||
8' | 625 | 5,000 | 200 | Optional Forced Air | 4" Axial | 4 | 20 | 1 | 0.56 | 0.70 | 0.54 | 10.82 | 0.63 | 30 | 50 | 2 | 208 | 12.8 |
14